How to Make a Whirligig
- Get a paper plate, a pair of scissors, a hole puncher, some string or yarn, and some coloring stuffs (crayons, color pencils, paints).
- Color the paper plate.
- Use the scissors and cut the paper plate in a spiral pattern. ...
- Use the hole puncher and punch a hole in the center of the paper plate.
- Tie a string in the punched hole and you’re done!
How to make a whirligig?
The first step in how to make a whirligig is to cut out dadoes in centers of propeller arms (D), then temporarily put the arms together and mark diagonal cuts where blades are attached. Blades must all tilt the same direction. Set arms in a 45-degree notch cut into a 2x6 and make cross-cuts every 1/4 inch, using 2x6 as a depth guide.
How do you make a whirlygig out of cardboard?
Glue one piece onto your recycled cardboard scrap, cut around it with the scissors, and then glue the second pattern onto the reverse. Poke two small holes in the whirlygig with the kitchen skewer and thread the string through, tying in a knot once done. That’s all! Now just twirl and whirl.
What kind of paper do you use to make a whirligig?
Kids can also run around with them and watch as the whirligig twists wildly with wind velocity! When they kids are tuckered out from running, hang the whirligigs outside and watch them dance in the sweet little fall breezes. Thick Paper – I recommend a medium weight card stock. Lightweight paper will stretch too much and deform.
How do you make a circle with paper strips?
Start by rubbing glue from a glue stick all over one of the circles. Arrange one end of the paper strips evenly around the circle. Keep adding glue as they overlap around the circle. Cover the top with another circle to secure them in place.
How does a paper whirligig work?
The uncoiling of twists in the string applies torque, or rotational force, to the paper disc, causing the disc to spin. The disc builds up speed as the string unwinds, and you'll hear a “whirring” sound as it cuts through the air.
How do you make a whirligig cardboard?
Glue one piece onto your recycled cardboard scrap, cut around it with the scissors, and then glue the second pattern onto the reverse. Poke two small holes in the whirlygig with the kitchen skewer and thread the string through, tying in a knot once done. That's all! Now just twirl and whirl.
What is the whirligig made of?
Also known as buzzers, these whirligig toys were once made with nothing but clay, bone and hide. In the 1920s, they were made with a button or coin and a piece of string. So the whirligig began as a hand toy, but by the mid 1850s, whirligigs were more and more an art form.
What was originally called a whirligig?
Haven and Charles Hettrich in patented the first yo-yo in 1866 (U.S. Patent 59,745 ), under the name whirligig. The toy that is now known as the Yo-Yo originally was known as the whirligig in the United States.
How do you make a wind spinner?
0:004:03Make a wind spinner. Easy and fun DIY project. - YouTubeYouTubeStart of suggested clipEnd of suggested clipShape. So I'm going to run a piece of quarter inch all thread all the way. Through. I'm going toMoreShape. So I'm going to run a piece of quarter inch all thread all the way. Through. I'm going to lock this all together temporarily. With a nut on each side to hold it together while I paint.
How do I make a cardboard spinner?
0:002:15Homemade cardboard game spinner - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn a sheet of paper glue your circles down on to the card board using the glue stick.MoreOn a sheet of paper glue your circles down on to the card board using the glue stick.
What's another name for a whirligig?
In this page you can discover 7 synonyms, antonyms, idiomatic expressions, and related words for whirligig, like: carousel, teetotum, carrousel, merry-go-round, roundabout, top and spinning-top.
What does a whirligig symbolize?
Whirligigs further represent the far-reaching consequences of action by serving as catalysts for significant realizations for people Brent has never met and will in all likelihood never meet.
What is the purpose of whirligigs?
In short, it's a weathervane that has a windmill on one part to assist it in better catching the wind. Even though whirligigs are designed to show wind direction, they have become more related to their use as children's toys and in yard ornamentation.
What does a whirligig look like?
Whirligig beetles look like a blur as they gyrate endlessly around each other on the water. These beetles are oval, streamlined and usually blackish, sometimes bronzy or metallic. The forelegs are long and slender; the middle and hind legs are short, flattened, and fold tightly under the body.
Who invented the whirligig?
James L. Haven and Charles Hettrich in patented the first yo-yo in 1866 (U.S. Patent 59,745 ), under the name whirligig. The toy that is now known as the Yo-Yo originally was known as the whirligig in the United States.
Who made whirligigs?
Farm machinery repairman, Vollis Simpson, began making gigantic kinetic sculptures at his family farm in Wilson County when he was nearing retirement age. He kept making his “whirligigs”–seven days a week–until about six months before he died at the age of 94 in May of 2013. By that time he was famous.
How do you make a paper pinwheel?
InstructionsDraw Lines. Using a ruler, mark the center of your square paper with a pencil. ... Cut Down the Lines. Use the scissors to cut down the diagonal lines that you just marked on your paper. ... Fold and Pin. Fold every other point into the center dot and put a pushpin through the paper. ... Attach to Straw.
What is a whirligig toy?
The whirligig is a simple toy consisting of a flat disc with two central. holes. When a string is threaded through the holes, twisted and then pulled. taut, the disc spins and hums.The whirligig (buzzer, buzz disc, and whizzer) has been recovered at dig sites all over the world.While we will probably.
How do you make whirligig out of wood?
2:288:30Make an easy wood whirligig - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor the center rod. And I'm making a second offset hole and while I'm at it I'll drill holes for theMoreFor the center rod. And I'm making a second offset hole and while I'm at it I'll drill holes for the guy's legs. And his body where they're going to hinge. Together.
How to make a whirlygig
This post may contain affiliate links. I may receive commissions for purchases made through links in this post at no cost to you.
Get the Whirlygig template
Get the free printable whirlygig template delivered to your inbox by entering your name and email address in the spaces provided.
What type of paper do I use for card stock?
Thick Paper – I recommend a medium weight card stock. Lightweight paper will stretch too much and deform.
Do paper crafts need to be complicated?
The whirligig proves that paper crafts do not need to be complicated to be engaging. If you like paper toys or other paper crafts for kids be sure to check out: Paper Helicopters, Zappy Zoomers, and Tyvek Kites.
Do whirligigs spin?
These whirligigs will start spinning with the slightest disturbance of air near them. Kids can also run around with them and watch as the whirligig twists wildly with wind velocity! When they kids are tuckered out from running, hang the whirligigs outside and watch them dance in the sweet little fall breezes.
What is a Twirligig Paper Spinner Toy?
You have probably heard of a whirligig before. A Whirligig, by definition, is any kind of spinning toy or object. In colonial times, they made whirligig toys out of buttons and string.
How to secure paper strips to a circle?
This time bring the other ends of the paper strips up and attach them to the circle. Once they are all attached with glue, cover again with another circle to secure them.
How many circles to cut for paper strips?
You will also need to cut 4 circles for attaching the paper strips. My circles are a 1 1/2 inches in diameter.
How many strips of paper to make a rainbow?
Cut 8 strips of paper. I cut it from the long side of the paper, 11 inches long. They are just over 1/2 inch in width. I used 8 different colors to make it rainbow and colorful. But you can do it all from one piece of paper, too!
How to keep a spinner toy from moving?
Reach the glue gun in to the under side of that top circle and add some hot glue there , too. This will keep the whole top section from moving as the spinner toy spins.
How to make a whirligig?
The first step in how to make a whirligig is to cut out dadoes in centers of propeller arms (D), then temporarily put the arms together and mark diagonal cuts where blades are attached. Blades must all tilt the same direction. Set arms in a 45-degree notch cut into a 2x6 and make cross-cuts every 1/4 inch, using 2x6 as a depth guide. Break away pieces and clean up saw kerfs with chisel.
What is a whirligig made of?
Family Handyman. Folk art whirligigs fashioned from scraps of wood and metal have been popular for hundreds of years. In fact, George Washington bought some for his grandchildren during his trip back to Mt. Vernon after winning the Revolutionary War. You, too, can build this marching, spinning red-white-and-blue whirligig.
How to make a whirligig weather vane?
Drill a 1/4-inch hole in the platform (Fig. A) for the pivot pin. Putting most of the weight of the whirligig in the back makes it function as a weather vane. Ream the hole out a bit; the 1/4-inch pin should be snug, but the whirligig should still spin easily. Insert the pin two inches into a post and set it up in the yard or on a deck.
How deep do you drill holes in a flag pole?
For color, add beads before and after each spinner. Drill 3/4-inch-deep holes into the platform and the flag-pole, and push in the brass rods.
How to cut propeller arms?
Cutting the propeller arms (D) is the trickiest woodworking of the project. Use a fine-toothed saw to make kerfs for the dadoes where the arms cross and for the four angled faces where the propellers are attached (Photos 1 and 2), then carefully use a chisel to remove the waste.
