Using Household Items
- 1 Connect LEGO pieces together to make a useful stand. ...
- 2 Bend up the bottom portion of a coat hanger to hold your iPad. ...
- 3 Angle a metal bookend to keep your iPad upright. ...
- 4 Tie 6 pencils together with rubber bands to use as a tripod. ...
- 5 Use a cutting board as an iPad stand when you’re in the kitchen. ...
How do I make a DIY tablet stand?
Build a handsome DIY tablet stand with scraps of cabinet-grade plywood. Start with a 6"-wide, 11"-long chunk (with a thickness, ideally, of 5/8"). Then cut a 3/8"-wide slot at 25 degrees, about an inch or so in from a 6"-wide edge. Using a sander, carve out a divot for the home button, then chamfer the edges for a finished look.
How do you hang an iPad on a coat hanger?
Bend up the bottom portion of a coat hanger to hold your iPad. Take some pliers and work the bottom metal wiring of a hanger out of its traditional shape. Adjust the wide triangle of wire into a long oval, leaving the hook portion unbent. Finally use the pliers to curve up the bottom section of the hanger up by 1 to 1.5 inches (2.5 to 3.8 cm). [2]
How do you bend a wire to install a tablet?
Mark the wire at 1/4" from the smooth end. Hold the wire with the two pliers. One on either side of the mark and bend it 90 degrees. Lay the tablet on the support plate and put the bent end of the wire on top of the tablet next to the right hand hole at the top of the support plate.
How do you make a tablet stand out of packing tape?
The round footprint of a packing tape roll is wide enough to keep your tablet upright, but for stability, the key here is to put the groove (for the tablet's base) off to one side of the centerline. Build a handsome DIY tablet stand with scraps of cabinet-grade plywood.
How do you make a makeshift tablet stand?
If you have a couple of wine corks on hand, this is a fun DIY tablet stand to make. Here's how to do it: Drive a drywall screw through each cork, then tie cotton rope to the tip and head of each screw. The rope should be just long enough to hold the tablet steady as the corks meet the table top.
How do you make a hanger stand?
0:072:09Coat-hanger book stand | DIY book stand | super simple - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you first want to get a coat hanger and some pliers. Now I just want to bend the coat hanger withMoreSo you first want to get a coat hanger and some pliers. Now I just want to bend the coat hanger with your hand just like this. Now just go to the ends. And get some pliers.
How do you stand up a tablet?
0:001:11How to Make a Tablet or Phone Stand - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis. Open it up place it on the table and there we have our simple tablet. Stand. You can make oneMoreThis. Open it up place it on the table and there we have our simple tablet. Stand. You can make one for your phone out of a plastic loyalty. Card. It can hold your device either way up.
How do you make a phone stand with a hanger?
0:472:56diy wire coat hanger phone stand project build - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo measure about a half an inch and bend it to the right. You want to measure the length of yourMoreSo measure about a half an inch and bend it to the right. You want to measure the length of your phone. So it sits comfortably in the holder. From my phone it's about three and a half inches.
How do you make a stand?
How to make your standGet the “lay of the land”Link to the common goal.Back it up with data.Create a compelling narrative.Don't make it personal.Don't take things personally.Show respect.
How do you use a tablet holder?
Put your tablet against the flat surface of the tablet stand. Place the small bungee cords into the holes on the tablet stand to securely hold the corners of your tablet in place. Adjust the height and angle of the tablet holder, using the adjustable arms to keep your tablet exactly where you need it.
How do you make a homemade tripod for IPAD?
0:352:48How to make a cheap ipad tripod mount - YouTubeYouTubeStart of suggested clipEnd of suggested clipI just used some rubber bands really low-tech there some rubber bands just. Just. I wasn't going toMoreI just used some rubber bands really low-tech there some rubber bands just. Just. I wasn't going to scratch the iPad.
What can I use to prop up my phone?
0:171:43DIY smartphone stands - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first one you will need a paper clip. And a pair of pliers. Start. By straightening out theMoreThe first one you will need a paper clip. And a pair of pliers. Start. By straightening out the paper clip. And place your finger in the center of the band. And then bend the band.
How do you make a mobile wall stand at home?
0:093:50How to make mobile holder/ mobile charging hanging/wall ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipMonopod tim.MoreMonopod tim.
How do you make a phone stand out of Popsicle sticks?
0:484:11How To Make A Popsicle Stick Cell Phone Stand ( Easel | Picture Holder )YouTubeStart of suggested clipEnd of suggested clipSo for this little phone holder you're gonna need nine popsicle sticks and the first thing you wannaMoreSo for this little phone holder you're gonna need nine popsicle sticks and the first thing you wanna do is make the sides and to do that you're gonna have two kind of like this.
How do I keep my tablet straight?
1:496:47How to Keep Your Tablet Upright: The Best Tablet Stand and HolderYouTubeStart of suggested clipEnd of suggested clipAll right so you can position this at any angle. As you can see super easy it holds really firmMoreAll right so you can position this at any angle. As you can see super easy it holds really firm right here like it's got a firm grip it's got a really nice grip on my iPad. I use it to watch movies.
How do you make a wooden tablet stand?
0:251:38How to Make a Barnwood Tablet Stand - DIY Network - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep 2 make a mark 1 inch from the bottom on the 12 inch board and draw a line 3 and 5/8 inches longMoreStep 2 make a mark 1 inch from the bottom on the 12 inch board and draw a line 3 and 5/8 inches long make another mark at 2 inches and draw another line 3 and 5/8 inches long connect those two lines.
Step 1
Cut the coathanger fairly close to the hook and straighten it as much as you can. Bend it as in the photo, centering the bend in the coathanger as much as possible. Don't worry if it isn't precise, we can cut off any excess so as to even things up later. Make sure the bends are square and that the remaining wire is more or less parallel.
Step 2
Now bend the part you just bent so it is 90 degrees from the rest of the coathanger as shown in the photos. Again, make sure everything is parallel and square.
Step 4
Cut the "tails" leading off from all that bend work you just did so that they are more or less even. Now bend the remainder of the coathanger so as to look like this. You are done. Test it with your tablet and adjust the wires so as to achieve a comfortable viewing angle.
Step 5
The stand works in either horizontal or vertical mode. The second photo is the first one of these I made, designed to hold an iPod for either viewing or photography purposes. I did not think the iPod style was sufficiently strong to hold a larger, heavier tablet, hence the extra bends.
10 DIY Samples to Make Your Own Tablet Stand
There is no perfect solution in conveniently handling your tablet other than having a tablet stand. Besides the comfort, having the tablet far away from your eyes than you used to helps keep your vision safe from its radiation. However, if you still don’t have one, you may try to make your tablet stand with this DIY guide we prepared for you.
Lamicall Tablet Stands
Lamicall is one of the leading brands when it comes to high-quality gadget accessories. It is now the top brand on the Amazon platform and has helped millions of people get that convenience they deserve when handling their devices. Its network has reached more than 80 countries, thus, proves its good standing in the industry.
How to attach wire to tablet?
Put all the wire pieces in the support plate and test fit the tablet. it will be a little tricky with the wire not glued in yet. You are looking for the wire guides to hold the tablet securely but not scratch or drag on the tablet. You can adjust the wire with the pliers until you have a fit that you like. Glue the wires into the holes with super glue. Use tape to hold everything in place as it is drying.
How to make a tablet neck?
First cut the plastic/wood for the tablet support plate to the width of the tablet and 2/3 of its height. Drill a 7/16" hole in the support plate. Center it between the left and right sides and about 2/3 of the height of the plate. The hole should be at the center of the back of the tablet when the bottom edge of the tablet and the support plate are lined up. Tap the hole for 1/4" pipe threads. If you don't have a tap you could just drill the hole over-sized and glue the neck in.
1. Prepare The Materials Needed
A coat-hanger is the same as the ones from the dry cleaners, the metal one.
2. Unknot The CoatHanger
With pliers, hold the hooked end to the portion where the two ends of the wire are wrapped. Rotate the coat hanger in one correct direction to unknot the twist. Some “spring” might possibly be left in the wire, so release it slowly and carefully. And now you may straighten the wire.
3. Create Few Bends
First, try to make a little “U” shape that bends on both ends that have not got curve parts using the pliers; this is one of the endpoints the string will be connected.
4. The Shoulder Area
Put a small bend in the wire used below the phone holder bit just; therefore, it is at a more reasonable and good angle.
5. The Finishing UpPortion
Putting some extra strings across the wire is good for the reason to stop it from falling down when putting the phone into it. It is more useful to place a small twirl at the neck or shoulder area. Bend or curve it out right after the bend using the needle nose pliers, then bend it back right after the curve to follow the original direction.
6. Now Run SomeTest If It Works Out
Once a piece of metal string is pressing your chest, and this really annoys you, The best thing to do is attach a piece of paperboard to stretch the load. And also, it can be somewhat tricky getting a good balance on it because it has the possibility to ‘flop over’ to the right or left direction.
How to make a tablet stand?
Build a handsome DIY tablet stand with scraps of cabinet-grade plywood. Start with a 6"-wide, 11"-long chunk (with a thickness, ideally, of 5/8"). Then cut a 3/8"-wide slot at 25 degrees, about an inch or so in from a 6"-wide edge. Using a sander, carve out a divot for the home button, then chamfer the edges for a finished look.
What is a lightweight stand made of?
Perfect for scenarios in which a flat surface is unavailable, this lightweight stand (which you can break down and transport) is made of PVC pipes and fittings —easy and inexpensive materials to work with.
What is a Technic building set?
Grab your youngster’s LEGO collection and hopefully among its many colorful blocks, you’ll find pieces from a Technic building set—the sort used to build little cars with rack-and-pinion steering. These kits include bars and pins that firmly hold LEGO pieces together, enabling you to construct a sturdy and definitely fun-looking DIY tablet stand. As a practical and whimsical finishing touch, incorporate rubber wheels to protect your tablet from scuffing.
Can you cook with a tablet?
Cooking in the kitchen with a tablet is a potential disaster. Cinnamon dust can cover every speaker hole on the device; splattered sauce can muck up the screen. Elevate the tablet out of harm's way—while keeping the display at eye level—by simply bending an inexpensive wire coat hanger with linesman pliers—$0 and ingenious!
Can you make a stand out of cardboard?
You can also create a stand with cardboard. Repurpose a FedEx box or, alternatively, use the one your tablet came in (avoid flimsier material like cereal boxes). The beauty of this design is the way it folds in half.
How to hold iPad on coat hanger?
Bend up the bottom portion of a coat hanger to hold your iPad. Take some pliers and work the bottom metal wiring of a hanger out of its traditional shape. Adjust the wide triangle of wire into a long oval, leaving the hook portion unbent. Finally use the pliers to curve up the bottom section of the hanger up by 1 to 1.5 inches (2.5 to 3.8 cm).
How to make a stand out of cardboard?
Lay down a flat piece of cardboard to use for your stand. Flatten out some cardboard and lay it on a smooth surface. If you don’t have any cardboard on hand, see if you can find any shoeboxes or delivery boxes lying around your home. If possible, layer a second sheet of cardboard beneath the initial piece to serve as a cutting board.
How to draw iPad screen?
Trace your iPad twice on the flattened cardboard. Lay your tablet screen-side-down onto the cardboard. Using a marker or pen, trace around the edge of the iPad to provide an exact drawing of your tablet’s dimensions. Do 2 separate tracings on this cardboard, both identical in size and shape.
How to get a camera on an iPad?
Hold a piece of cardboard up to your iPad and find the camera. Sketch a small rectangle on the cardboard to represent the camera’s approximate location. After you’ve set aside your tablet, lay the marked cardboard sheet flat, and cut away this small section of cardboard with your cutting tool.
How to keep iPad upright?
Angle a metal bookend to keep your iPad upright. Take the upright, arced portion of a metal bookend and push it backwards. Bend this bookend to the angle that you plan on using to view your tablet. To prevent the iPad from slipping when you lean it against the metal, stick 2 binder clips on the bottom, horizontal portion of the bookend.
How to make a Lego stand?
1. Connect LEGO pieces together to make a useful stand. Take a variety of rectangular LEGO bricks and stack them on top of one another. Try to use a large, flat rectangular LEGO as the base of the stand, then stack more bricks in 2 upright towers in the center of this rectangle.
How to cut cardboard for iPad?
Measure about 0.5 in (1.3 cm) above the top edge of your iPad tracing. Use the box cutter or X-Acto knife to slice out this extra strip of cardboard. To make your measurements more exact, trying marking the strip’s dimensions in permanent marker before cutting.
