how do you make a wooden clock

How to make a wood clock

Full Answer

How to make a DIY wood clock?

Materials needed to make a wood clock

• Thin Scrap plywood (I used 7/32″ plywood underlayment) – you can use 1/4″ plywood too.
• Scrap 1/4″ MDF or plywood
• Wood stains in a few colors. ...
• Clock mechanism kit (look for shaft length based on the thickness of your plywood)
• Jigsaw or scroll saw or band saw
• Power drill
• Table saw or a BladeRunner X2 (which is what i used)
• White paint pen
• A strong glue

How to make a wall clock out of wood?

How to make a wood clock

1. Cut base. Draw a circle on the MDF/plywood in the size you like. ...
2. Prepare Strips. Rip the pieces of thin plywood/underlayment into 2″ wide strips. ...
3. Attach strips. Layout the strips on top of the MDF circle and adjust until you like the design. ...
4. Cut off strips. ...
5. Add clock numbers. ...
6. Add wall clock kit. ...

How to resin a wooden clock?

How to Make a Resin and Wood Clock

1. Preparing the Wood. Since the reclaimed barn wood that I have still has the old paint on it, I needed to do some work to it before jumping ...
2. Painting. The way I decided to use resin to modernize the barn wood was by adding a space nebula to the board.
3. Making the Galaxy. ...
4. Preparing for Assembly. ...
5. Final Assembly. ...
6. Conclusion. ...

How to make your own wall clock?

1. Assemble DIY Wooden Clock Dial. Cut four 1×10 boards a little longer than you want your clock diameter. ...
2. Finish the DIY clock with paint or stain. Sand the wood round and finish as desired. ...
3. Add Roman Numerals to the DIY Clock. I used this technique for applying the numbers to the clock. ...
4. Route out hole for clock movement. ...
5. Add clock hands. ...

How to drill a hole in a clock motor?

How to carve out wood?

How long to spin the minute hand?

Where to place a motor on wood?

Can you hang a clock on the wall?

See 2 more

About this website

How do you make a wooden clock step by step?

How to make a wood clockStep 1 – Cut base. Cutting your own base is optional. ... Step 2 – Prepare Strips. Rip the pieces of thin plywood/underlayment into 2″ wide strips. ... Step 3 – Attach strips. ... Step 4 – Trim the strips. ... Step 5 – Add clock numbers. ... Step 6 – Add wall clock kit.

What type of wood is best for a clock?

Black walnut is an incredibly important tree commercially as the wood is a deep brown color and easily worked which makes it excellent for the manufacture of clocks.

How do you make a wooden wall clock at home?

Step 1: Assemble DIY Wooden Clock Dial. Cut four 1×10 boards a little longer than you want your clock diameter. ... Step 2: Finish the DIY clock with paint or stain. Sand the wood round and finish as desired. ... Step 3: Add Roman Numerals to the DIY Clock. ... Step 4: Route out hole for clock movement. ... Step 5: Add clock hands.

How can I make my own clock?

How to Make a ClockSelect and prepare your base. You can turn almost anything into a clock base, as long as you can drill a hole in it. ... Choose your clock mechanism. ... Drill a hole in the base. ... Add your decorations. ... Assemble and hang your clock.

What is the best material for a clock?

Wood is one of the most common materials used for making clocks.

What wood are grandfather clocks made out of?

There is a wide variety of materials from which grandfather clocks are made. Many grandfather clocks are constructed using hardwoods and veneers while finishes are formulated to gently enhance the natural beauty of select woods. The finishing material is commonly made from wood such as beech, cherry, mahogany and oak.

What materials are used to make clocks?

Clocks are typically composed of multiple types of materials such as wood, metal, paint, plastic, etc., which have unique behaviors and environmental interactions, making treatment options complex.

How do you make a desk clock?

0:046:19How To Make a Walnut Desk Clock (ep15) - YouTubeYouTubeStart of suggested clipEnd of suggested clipI took some eight quarter walnut and started truing up two surfaces. My original plan was to haveMoreI took some eight quarter walnut and started truing up two surfaces. My original plan was to have the top back of the clock have matching grain patterns. You'll see later why that didn't work out.

How do you install a wall clock?

Hang your clock on the adhesive hook. Line up the back of your clock with the hook. Slip the mounting part of the clock over the hook. If your clock is tilted or slanted, adjust it on the hook so it is even. If your clock doesn't hang evenly, the ticking mechanism could get off balance and tell the wrong time.

How do you make a clock with a moveable hand?

0:122:3811 - How to make a Paper Clock - Arts and Crafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat we need for today's activity is one paper plate two strips of black construction. Paper splitMoreWhat we need for today's activity is one paper plate two strips of black construction. Paper split pins a pair of scissors. Red acrylic paint glue a paint brush a black marker a paper punch.

How do you make a round clock?

0:2317:37Making a DIY Round Wall Clock - YouTubeYouTubeStart of suggested clipEnd of suggested clipLet's go to work to make this clock I've selected to use a 5/8 inch thick rough cedar board and IMoreLet's go to work to make this clock I've selected to use a 5/8 inch thick rough cedar board and I just need to cut about four or five pieces of it I've set up a stop block here on my chop saw so that

How do you make a clock at home for kids?

1:505:32Telling Time For Children - Learning the Clock - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight now the hour hand is between the 11 and the 12.. So is this 11 o'clock or 12 o'clock. It isMoreRight now the hour hand is between the 11 and the 12.. So is this 11 o'clock or 12 o'clock. It is still 11 o'clock it will not be 12 o'clock until the hour hand points right at the 12..

How can I make a digital clock at home?

Building Your Own Digital Clock12-volt AC transformer (Jameco part #115602)Bridge rectifier (Jameco part #103018)7805 5-volt regulator (TO-220 case) (Jameco part #51262)Two 470-microfarad electrolytic capacitors (Jameco part #93817)5.1-volt zener diode (Jameco part #36097)1-K-ohm resistor (Jameco part #29663)

How do you make a paper clock?

How to Make the Paper ClockStep 1: Adhere number stickers around the plate, using a clock as a guide for proper placement.Step 2: Trace the two (2) clock hands onto decorative paper; cut out. Punch a hole near the bottom of each clock hand.Step 3: Use a sharp pencil to punch a hole in the center of the plate.

How do you make a simple cardboard clock?

Clock design instructions: Flip the plates upside down on the cardboard and trace them with pencil onto the cardboard. Then, cut the circles out. Glue colored construction paper onto the front to make the face of the clock. Use a ruler and start by marking 12, 3, 6, and 9 on the small circle.

How do you make clock in little alchemy?

Combinationstime + electricity.time + wheel.time + tool.

30 DIY Wood Clock Plans and Ideas You Can Build - Epic Saw Guy

You will fall in love with its design at first sight. It’s eye-catching with a unique and outstanding structure. Prepare nine square blocks of size 4×4 inches, about 1.3 inches in thickness.

How to Make a Wooden Clock from Scratch - Wooden Earth

Have you ever thought about building your own wooden clock? Apparently people do it. Absolutely awesome process, very tedious and we got a little article here to show you exactly what this process looks like. This clock that we're building could be a gift for your daughter and this is something you can pass on to her when she eventually moves on and starts her own life. The design of this ...

Where is the clock mechanism on a circular board?from justmeasuringup.com

I had purchased a clock mechanism to insert into the circular board. It’s a square device that sits in the back of the clock, protruding through the center where the hands are attached to on the other side.

What does each line represent on a clock?from justmeasuringup.com

Each line represented an hour on the clock dial. I made all these lines on the back side of the clock, and used them as references later when placing the clock numbers.

How to carve out wood?from instructables.com

Using a chisel and a hammer, carve out the wood within the outline.

How to make a pivot point on a board?from justmeasuringup.com

Simply tie a string (or wire) to a pencil. Then pin the other end of the string to the center of your board (to be used as a pivot point).

How long to spin the minute hand?from instructables.com

With a finger, spin the minute hand for a full twelve hours to ensure the hour hand points correctly to the number

Where to place a motor on wood?from instructables.com

Placing the tip of the motor on the center of the wood, trace the motor so it gives you the outline of the wood you will eventually need to chisel out.

Can you hang a clock on the wall?from instructables.com

You have now completed your clock. You can hang it up on the wall or whatever you would like to do with it.

How to drill a hole in a clock motor?from instructables.com

Measure diagonally off the four corners to find the location for the center hole. This hole will accommodate the clock motor shaft. Then, drill the hole.

How to carve out wood?from instructables.com

Using a chisel and a hammer, carve out the wood within the outline.

How long to spin the minute hand?from instructables.com

With a finger, spin the minute hand for a full twelve hours to ensure the hour hand points correctly to the number

Where to place a motor on wood?from instructables.com

Placing the tip of the motor on the center of the wood, trace the motor so it gives you the outline of the wood you will eventually need to chisel out.

Can you hang a clock on the wall?from instructables.com

You have now completed your clock. You can hang it up on the wall or whatever you would like to do with it.

Where is the clock mechanism on a circular board?

I had purchased a clock mechanism to insert into the circular board. It’s a square device that sits in the back of the clock, protruding through the center where the hands are attached to on the other side.

What does each line represent on a clock?

Each line represented an hour on the clock dial. I made all these lines on the back side of the clock, and used them as references later when placing the clock numbers.

How to make a pivot point on a board?

Simply tie a string (or wire) to a pencil. Then pin the other end of the string to the center of your board (to be used as a pivot point).

Can you make your own clock?

If you are thinking of making your own clock – or if you have a love for clocks like I do, definitely make your own. You can use anything – it doesn’t even have to be a piece of wood .

DIY Wooden Clock Plans

Have you ever wanted to build your clock from scratch? Our DIY Wooden Clock Plans are possible and easier than you might think. Make a clock for yourself or build one as a gift cherished forever.

How To Build A DIY Modern Live Edge Wall Clock

Woodworking Jedi and Weekday Crafter Jeff Lyden brings you another woodworking project! This week we’re turning a live edge slab found in the scrap bin at our local home improvement store into a modern wall clock. We’ll create the veneer for the face of the clock using a router and automatic vacuum system to keep everything clean.

Large Wooden Wall Clock

How to make a large wall clock. Includes instructions on how to mark the back of the clock board and attach the hands and how to connect the different hardware components, including the movement and hardware required to mount it on the wall. This wall clock features a large wooden face with thick wood slats to create a chunky and rustic feel.

Wood And Metal Wall Clock

At this point, you're probably asking yourself, "Do I really need another clock?" and the answer is yes! You do! And you should make it yourself. Inspired by watches, this metal wall clock is a great way to add industrial flair to any room. The metal case houses the movement; natural metal finish prevents tarnish and rust.

Easy Two-Toned Clock

Creating a modern-looking wooden clock can seem like a daunting task, but this easy design from Woodshop Diaries quickly shows you how it's done. Start with two pieces of wood in different tones, then pair them together with some glue and nails.

Scrap Plywood Wall Clock

You've got scrap plywood pieces lying around from other projects. Why not put them to good use? In this easy-to-follow how-to guide, pretty Handy Girl shows you how to build a wall clock out of scrap plywood. With her simple instructions and accompanying video, you'll have a beautifully handcrafted wall clock in no time.

Butterfly Silhouette Clock

The real beauty of this handmade clock is in the butterfly silhouettes. This could be a teaching moment for the budding artist in your home or the perfect conversation piece to keep people talking about.

How to clean a wooden clock?

Instead of using oil, use a dust rag, fine steel wool, or sand paper to wipe dust and debris .

How to make a clock keep time?

The pendulum and drive weight, along with the escape mechanism, are what actually make your clock keep time. Again, the specifications here will depend on what your instructions say to do. Generally, you will make the drive weight using wood and lead shot. Add the hands and any other decorative elements.

How do the gears of a wooden clock work?

The rough diagram above shows how the gears of a wooden clock interlock and move to keep time. The yellow, red, and dark blue gears aren't connected to each other, rather they interlock with each others' pinions (the green and light blue wheels), which are affixed to the main gear wheels. This changes the speed by which the driving gear moves the next and is determined by the size and teeth number of the pinion.

How many hands does a clock have?

As shown above, roughly, a clock usually has three gears in its gear train, each moving one of the three hands indicating seconds, minutes, and hours.

Why do clocks need power tools?

Because of the precision required in cutting and sanding the teeth of the gears, escapement wheel, and other parts , making even a simple wooden clock demands access to power tools and a woodshop.

What are the parts of a clock gear?

The different gears are explained in detail below. Gear: Clock gears are actually made of four parts: the wheel, the arbor, the pinion, and the pivot. The wheel is the toothed circle that turns, hooking the other wheels with its teeth. The arbor is the axel of the gear.

What keeps a clock going?

Power source: What keeps the clock going? In the case of most homemade clocks, the momentum is created by a swinging weight, or pendulum, which moves the gears as it swings back and forth.

How to make a minute hand?

To make a minute hand, you need a gear ratio of 60 between the Escapement axle and the Minute Hand axle. For an hour hand, you will need a gear ratio of 12 from the Minute hand to the hour hand. The spreadsheet shows the formula and the calculations to get the number of teeth for each gear.

How long does it take for a pendulum to swing?

If you have too heavy of a weight, you will not have enough energy to keep it swinging. For our clock, we want to have a period of 2 seconds. That way, it will take the pendulum 1 second to swing to one side. With each swing the escapement will allow the escape gear to turn one tooth at a time.

How does a pendulum work?

The pendulum swings back and forth moving the escapement lever in and out of the escape gear, causing the gear to stop spinning. This allows the energy of the weight to be spread over a period of time so you are not winding the clock every 2 minutes. Ask Question.

What does the escape gear do on a pendulum clock?

As the pendulum swings back and forth, it rotates the escape lever in and out of the escape gear. This causes the clock gears to stop and start rotating every second.

What is the period of a pendulum?

The period of a pendulum is the time it takes to go from one side to the other and back again. The neat thing about pendulums is that this time, or period, is not dependent on the amount of weight or length of arc, it's dependent on the length of the pendulum.

Can a ratchet be turned counter clockwise?

It fits loosely over the axle of one of the gears, and pushes against the gear with a pin and lever. When the clock needs to be wound, the Ratchet can be turned counter-clockwise without moving the gear.

Can a 5 pound pendulum swing longer than a 2 pound pendulum?

So the pendulum with the 5 pound weight will swing for a longer amount of time, than the 2 pound weight. This is helpful because we want to keep the pendulum swinging. You can, however, have too much weight. As we will see next, the escapement helps give the pendulum a push.

How to drill a hole in a clock motor?

Measure diagonally off the four corners to find the location for the center hole. This hole will accommodate the clock motor shaft. Then, drill the hole.

How to carve out wood?

Using a chisel and a hammer, carve out the wood within the outline.

How long to spin the minute hand?

With a finger, spin the minute hand for a full twelve hours to ensure the hour hand points correctly to the number

Where to place a motor on wood?

Placing the tip of the motor on the center of the wood, trace the motor so it gives you the outline of the wood you will eventually need to chisel out.

Can you hang a clock on the wall?

You have now completed your clock. You can hang it up on the wall or whatever you would like to do with it.