Full Answer
How do you make an octagon table top?
You’ll cut off the corners to create an octagon. Nose and cove molding: You’ll miter the ends of 8 pieces at a 22½-degree angle. ½-inch plywood table: 1 @ 48 by 48 inches. You’ll cut off the corners to create an octagon. 1x2 outer-edge trim: You’ll miter the ends of 8 pieces at a 22½-degree angle.
How do I build a poker table?
If you’re going to build a poker table though, you should have an open and well-ventilated area to work and at least a basic understanding of how to operate power tools. Measure corners on a 4 by 4 feet (1.2 by 1.2 m) sheet of plywood. Use a straight edge ruler to measure 14 inches (36 cm) from the corner of your plywood along the side.
What size do you cut plywood tables to make Octagon?
½-inch plywood table: 1 @ 48 by 48 inches. You’ll cut off the corners to create an octagon. 1x2 outer-edge trim: You’ll miter the ends of 8 pieces at a 22½-degree angle. 1x2 inner edge trim: You’ll miter the ends of 8 pieces at a 22½-degree angle.
How do you make an octagon pedestal with plywood?
Using a brad nailer and wood glue, assemble the pieces into an octagonal round base. I shot the nails at the very top and bottom of the pieces because we will use trim to cover these areas up. Now lets cut the bottom of the pedestal. Use the remaining oak plywood to cut an octagon shape 30" in width.
How do you make a octagon poker table?
1:0221:46How to build a poker table (for 8 players) over a weekend ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd seven eighths on each corner. So I made this stick. And make a mark. From both directions onMoreAnd seven eighths on each corner. So I made this stick. And make a mark. From both directions on each corner. Then. I take this straight edge align those two marks. And draw a line on the back side.
What are the dimensions of a octagon poker table?
For folding table models of octagon poker tables, they will usually come in dimensions of 48 by 48 by 30 inches or about 122 by 122 by 76 centimeters for 4 players. In comparison, tabletop poker tables will come bigger and be 50 inches or 127 centimeters wide.
How do you make a homemade poker table?
How to Build a Poker Table in 18 StepsStep 1: Mark the Plywood Game Table. ... Step 2: Cut the Plywood Game Table and Lid. ... Step 3: Miter the Edge Pieces. ... Step 4: Install the Outer Edge. ... Step 5: Cut and Install the Coaster Blocks. ... Step 6: Install the Inner Edge. ... Step 7: Attach the Apron. ... Step 8: Mark the Playing Surface.More items...
What is the best shape for a poker table?
The best poker table shape for you. Poker tables come in two common shapes - oval and round. You'll occasionally see an octagon or a modified oval shape but the standard oval and round are going to be the popular choice and more widely available.
How do you measure an octagon table?
How to Measure Tablecloth Size for Octagon TablesMeasure your table from the farthest point between two flat edges to the point directly opposite it. This is the diameter of your table.Measure the drop – how far down you want the tablecloth to hang. ... Add the diameter of the table to the final number of the drop.
How much does it cost to build a poker table?
The cost of a poker table is determined by the materials used in its construction and the table's overall quality. The cost of roll-up poker mats and foldable table-toppers ranges from $15 to $125. The cost of a collapsible poker table with legs ranges from $175 to $300. Permanent tables cost between $750 and $5,000.
What are the holes in poker tables for?
Each player is dealt two hole cards face down at the start of the hand. Throughout the course of the hand five community cards will be dealt face up in the center of the table. The hole cards are used in conjunction with the community cards to construct a five card hand. Making hands in Hold'em is very flexible.
How do you turn a table into a poker table?
0:103:18Turning mom's kitchen table into a SECRET poker table! - BrojectsYouTubeStart of suggested clipEnd of suggested clipThey spent something to win it's almost purpose-built to be turned into a poker. Table. For an extraMoreThey spent something to win it's almost purpose-built to be turned into a poker. Table. For an extra feature of this table we want to do a perimeter surround made of wood it has cup holders built-in.
What is poker etiquette?
Poker etiquette refers to how players should behave themselves while at the poker table. It involves an unwritten set of guidelines to follow that helps promote good sportsmanship, the speed of play, and a healthy atmosphere for the game.
What is the ideal size for a home poker table?
A standard round or octagonal table with a 54-inch diameter will comfortably seat four to five players, but for larger groups you should choose a 60-inch-diameter model or a Texas hold 'em table, which is oval and up to 108 inches (9 feet) long.
How much space do you need for a poker table?
Place the poker table and chairs in an area of at least 8 square feet for a 42 inch table and up to 12 square feet for a 54 inch version. Lighting needs to be overhead and bright enough to clearly see cards.
How much room do you need around a poker table?
Space Needed For A Poker Table. Ideally, you want at least 3 feet (1 meter) of clearance around a poker table to allow for adequate seating and movement around the room.
How much space do you need for a poker table?
Place the poker table and chairs in an area of at least 8 square feet for a 42 inch table and up to 12 square feet for a 54 inch version. Lighting needs to be overhead and bright enough to clearly see cards.
How long is a 10 player poker table?
44″ x 96″A table size recommendations are as follows: -42″ x 84″ for 8 – 9 players. -44″ x 96″ for 10 – 11 players. -48″ diameter round for 4 - 5 players.
How much room do you need around a poker table?
Space Needed For A Poker Table. Ideally, you want at least 3 feet (1 meter) of clearance around a poker table to allow for adequate seating and movement around the room.
What is the size of a card table?
Square card-table tops are generally 34 by 34 inches, rectangular ones are typically 48 by 92 inches, and most oval ones have long diameters measuring 48 inches. A standard size of a square card table is 36 inches.
How to use speed cloth on poker table?
Place your speed cloth playing-side down on a flat surface. Spray each section of the speed cloth’s underside with your adhesive. Lift your playing surface up , and gently lower it, playing-side down, on top of the speed cloth. Speed cloth is the green material used on poker tables.
How to cut corners of a table top?
Use a circular saw to cut the corners of your table top. Lay your plywood flat on a work bench or flat surface and secure it with clamps. Line the guiding line of your circular saw up with each pencil mark and pull the saw’s trigger. Let the saw carry itself through your line and don’t push while the saw is firing.
Can you recycle an octagon?
You’re going to recycle the octagon that you cut out as the center piece for the legs, so don’t throw that piece out.
Can you make a poker table?
By constructing a homemade poker table, you will ensure that it fits comfortably in your home and meets your specific needs. If you’re going to build a poker table though, you should have an open and well-ventilated area to work and at least a basic understanding of how to operate power tools.
How to make an octagon table?
Using a circular saw, cut the lines to lop off the corners of the table and create an octagon. Lay the ½-inch plywood for the lid on your work surface with its best side facing down. Place the table on top of the lid; position it so that the uncut sides face the lid corners. Draw the outline of the table on the lid.
How to make a game table out of plywood?
On the underside of the table, measure and mark the sides 14 inches from each corner. Using a straightedge, draw a line to connect the two marks at each corner.
How to make a coaster block table?
Lay a length of 1x2 flat on the table inside the ring of coaster blocks so that the edge of the 1x2 sits against the top edge of a coaster block. Mark the distance between the angled ends of two coasters. Miter the ends of the 1x2 at opp osing 22½-degree angles. Lay the piece in place, and mark the remaining pieces until all the pieces of the inner ring are sized. Apply glue to the underside and ends of each piece, set them in place, and nail through the underside of the table to secure them. To help position the nail gun underneath the table, cut a scrap piece of 1x 2 to the distance the inner ring sits from the edge of the table and nail it to a second perpendicular block to create a T-shaped spacer. Hook the T on the edge of the table with the stem underneath, and position the nail gun at the end of the stem.
How to attach a collar to a table?
Apply glue to the top edge of the collar, and place it on the underside of the table, realigned with your previous marks. Allow the glue to dry until it holds the collar in place—or toenail a few nails around its edge to hold it—and flip the table over. Using a countersink bit, prepare the pilot holes and drive 2-inch screws through the plywood and into the top edges of the collar.
How to make a 1x2 table?
Lay a length of 1x2 flat on the playing table flush with its edge. Mark the length of the side on the edge of the 1x2. Miter the piece at opposing 22½-degree angles so that the long edge matches the length of the table's side. Clamp the piece in place on the table. Mark and miter the remaining pieces. To keep the 1x2 pieces organized, number each side of the table and the underside of the corresponding piece.
How to mark a coaster with a combination square?
Miter one end of each ½x6 coaster at a 22½-degree angle. Use a combination square to mark the center point by drawing lines at a 45-degree angle from the corners of the straight-cut end of each piece.
What is poker night?
Poker night is the perfect time to catch up with friends and show off a good hand. To provide a handsome game table that's sure to make the guys take your bet—or bluff—more seriously, follow our free card table plans to build a table complete with a felt playing surface, insets for poker chips, and coasters. When the game is over, just fit the lid onto the surface to turn it into a dining table for the rest of the week.
Step 1: Pedestal Part 1
Lets make the pedestal of the table. First make sure you are wearing protective eyewear when building this project. Rip 8 pieces of Oak plywood to 29" X 7.5" X .75. Once you have all 8 pieces ripped to size, cut the sides to 22.5 degree angles. Using a brad nailer and wood glue, assemble the pieces into an octagonal round base. I shot the nails at the very top and bottom of the pieces because we will use trim to cover these areas up. Let the glue dry for 24 hours.
Step 2: Pedestal Part 2
Now lets cut the bottom of the pedestal. Use the remaining oak plywood to cut an octagon shape 30" in width. I did this using Surfcam and a CNC Router, but you can do this also with a little drawing and then cut with a jigsaw. Do this by drawing a 30" line vertically on the wood.
Step 3: Chip Trays
Cut the 8 - 1" thick pieces of oak to 20" X 6" Then cut 22.5 degrees off the ends so all 8 pieces will fit together 360 degrees. You can make the chip tray any way you like as long as the overall dimensions match. If you want the drink holder on the left instead of the right, or maybe you don't want a drink holder.
Step 4: Wood Transition
I added a wooden piece to transition from an octagon shape to a circle. I wanted the playing surface to be round, so this piece was perfect for the transition. Place the assembled chip trays on top of the 1/2" Oak Playwood. Using a pencil trace along the inside of the chip trays for your octagon shape.
Step 5: Assembly
Next you need to cut a base plate for the table. I used 3/4" MDF.
Step 6: Attach Table to Pedestal
Lay your table on top of the pedestal (may need an extra hand with this) Line the 3/8" hole of the table to the 3/8" hole to the pedestal.
Step 7: Playing Table and Stain
Once the table is tight on the pedestal you can use felt to wrap the circular playing table from step 4. When you wrap the circular playing table be sure it is tight and make sure there are no creases. I used velveteen and stapled it to the underside of the playing table. Use wood filler to fill any and all gaps in the table then sand the entire table with a 100-grit sandpaper ( be careful when sanding the plywood, you do not want to sand off the oak finish) After you rough sand the table use 400 grit sandpaper and sand a smooth finish to the wood.
Step 1: Materials, Cost and Tools
The first thing I bought was a Harley-Davidson 675 Folding Poker Table Top off Amazon for $106 with free shipping using my Prime account.
Step 2: Measuring and Cutting the Base Table
For this you will need the 50"x50" MDF board. This will be smaller than the 52" poker table top and will create a nice looking lip in the end. In my pictures you will see mine in two pieces. Since my car does not have a huge trunk I needed to cut it to fit it in. If you can avoid this do so. The first thing we have to do is measure out our octagon.
Step 3: Creating the Skirt
At this point I could of added have some legs and it would be a decent poker table. However I wanted to add a little more stiffness to the table and make it look more professional. So I decided to create a skirt going around the bottom edge of the table. This step I think is the hardest part. The cuts need to be precise and should not be rushed.
Step 4: Painting
The hard part is done and it's onto the easy part...painting. Lay down enough paper on the floor to cover the table and then some. Grab your matte black spray paint and start on one side. When spraying go from one end to the other end of the end enough times to just cover the side evenly. DO NOT over spray or you will get drips.
Step 5: Attaching Legs
I found some great legs on sale that have a base plant that attaches to the table and the legs screw into the base plates. This is a nice feature since I can un-screw the legs with ease and store the table when not in use. You will need to add a leg at every other corner on the bottom of your table.
Step 6: Adding Trimming to the Table Edge
Your table is almost ready and needs a few finishing touches. In this step you will cover up the edge of the table top. For this you will need your 8'x3/4" Black Corner Stripping, scissors and staple gun. First thing you want to do is mark where your screws are with a pencil, see picture below with notes.
Step 7: Prepping, Fitting and Attaching the Poker Table Top
Your table is ready for prepping,fitting and attaching your table top. If you went the same route as me and purchased a Harley-Davidson 675 Folding Poker Table Top you will notice on the back side there are 2 large Velcro straps and two hinges. You will need to remove the hinges and the Velcro straps that hold the table top together.