Step by Step: THE WRAPPED LOOP
- 1. Straighten and Polish Your Wire Use a set of nylon or plastic lined pliers to straighten obvious bends. ...
- 2. Measure and Cut Your Wire Once your wire is polished and straight, estimate (or use your ruler) to measure a 3 inch length of wire. ...
- 3. Make the 1st Bend With your fingers, hold your wire vertically (up and down). ...
How to make a wire wrapped loop with a wire cutter?
Wrap the wire around the round nose plier to form a small circle (Picture 2). Holding the circle using the chain nose plier, wrap the additional wire by hand at the bottom of the circle (picture 3 and picture 4). After wrapping two or three times, cut the additional wire using a wire cutter (picture 5). Now your wire wrapped loop is completed.
How do you wrap a chain wire?
Pick up the chain nose pliers in your dominant hand and grab the end of the wire with the tip of the pliers. With a firm hold on the round nose pliers in your non-dominant hand, snugly pull the wrapping wire around the shaft 2 or 3 times. These loops should wrap right next to each other.
How do you wrap a pendant with a loop?
OPTIONAL: Open the loop slightly and slide on the loop of your pendant or charm; close the loop. Grip across the loop with a pair of chain-nose pliers. Grasp the tip of the wire with chain-nose pliers and wrap it around the straight length of wire above the pendant, making approximately three tightly-wound wraps.
How do you bend a wire wrapped bead?
(If making a wire wrapped loop with a bead already in place, position the chain nose pliers next to the bead, making the bend 1/8-inch from the bead.) With your thumb, bend the wire over the jaw of the plier, forming a right angle, or a 90-degree bend. Switch to your round nose pliers.
How to make a bead with wire?
How to bend wire with a round nose plier?
How to make a bead with a chain nose plier?
How to tuck wire into wrapping?
What to do if playback doesn't begin?
How do you make a simple loop with a wire?
1:563:09How To Make A Simple Loop For Wirework Jewelry - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to take the end of the wire. And bend it at 90 degrees against our bead like that. We'reMoreWe're going to take the end of the wire. And bend it at 90 degrees against our bead like that. We're gonna measure 1 centimeter. Get that just right use our wire cutters.
How do you bend a loop in a wire?
8:5616:24Basic Wire Bending - Part Six: Curves and Loops - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou place the wire back in the pliers. And begin to form the loop by placing the wire up in theMoreYou place the wire back in the pliers. And begin to form the loop by placing the wire up in the larger round portion of the round beak of the plier. Start the first Bend.
How do you make a double wrap wire loop?
0:284:10Secrets to a Double Wrapped Loop - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd about two inches down from one end begin a wrap loop just bend your wire at a 90 degree angleMoreAnd about two inches down from one end begin a wrap loop just bend your wire at a 90 degree angle rotate your pliers bring the wire up and around the loop of the barrel to form a loop.
How do you make a wire eye loop?
1:535:34How to Make an Eye Pin from Wire - YouTubeYouTubeStart of suggested clipEnd of suggested clipGrab your lengths of wire. And you want to grab a length of wire that's about an inch longer thanMoreGrab your lengths of wire. And you want to grab a length of wire that's about an inch longer than what you actually want your eye pin to be and about an inch or so from the end grab the wire and bend.
How do you bend wire smoothly?
4:4520:52Wire Working Basics: How to create beautiful shapes from wire. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo angle your file and just spin the wire over it to make it nice and smooth you can also use.MoreSo angle your file and just spin the wire over it to make it nice and smooth you can also use.
How do you make a loop?
0:081:48How to Make a Simple Loop - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo create a simple loop thread a few beads onto a head pin. Take your round nose pliers and placeMoreTo create a simple loop thread a few beads onto a head pin. Take your round nose pliers and place them right above that last bead you just strung bend your wire to a 90-degree angle.
What do you need to make a wire loop game?
Step 1: MaterialsMetal wire.9 volt battery.LED or light bulb.Buzzer (optional)Wood base.Alligator clip wires.Wire stripper.
How do you make a wrap loop on a head pin?
0:402:21How to Wire Wrap a Head Pin Loop - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith your free hand wrap the head pin around the jaw of the plier pulling it slightly to one. Side.MoreWith your free hand wrap the head pin around the jaw of the plier pulling it slightly to one. Side. Now holding the beaded wire rotate the pliers half way back toward the top forming the loop.
How do you make a jewelers loop?
2:493:48How To Make A Wrapped Loop For Jewelry - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the wire around the top jaw to make a partial loop reposition the pliers to the bottom jaw toMorePull the wire around the top jaw to make a partial loop reposition the pliers to the bottom jaw to continue pulling the wire around to make a complete loop.
How big is the loop in eye pin?
The loop size will depend on how much wire you leave past the end of your beads, and around which part of your pliers you bend the loop. A good loop size is usually about 1/3 of the way from the tip of your pliers, with about 8mm of wire.
What gauge wire are eye pins?
18- to 22-gauge wireIn general, head pins and eye pins are made using 18- to 22-gauge wire, typically soft or half hard, depending on how hard you want to work and how they'll be used.
How do you bend a wire without damaging it?
0:3111:18NO TOOLS? NO PROBLEM! // Ring Making Without Tools ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then for the nail clippers you can also clip. It quite easily and the other option is to justMoreAnd then for the nail clippers you can also clip. It quite easily and the other option is to just literally bend it back. And forth. And you can bend it quite easily. So that's the aluminum.
How do you bend wire without marking it?
7:0010:47How to Avoid Leaving Tool Marks in Wire - Tips and Strategies - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse your fingers to bend. The wire like so so you see I've actually achieved the same thing with anMoreUse your fingers to bend. The wire like so so you see I've actually achieved the same thing with an actual smoother band. Just by gripping on the end.
What do electricians use to bend?
13:5722:06How to bend Electrical Conduit Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil that conduit the back side of it is lined up with that line and they're parallel to each otherMoreUntil that conduit the back side of it is lined up with that line and they're parallel to each other and it doesn't have to be perfect but both bends should be the same. So that's the first one.
How do you bend wire at home?
0:5219:40How-to Form, Bend, Manipulate, Shape, Break, Straighten, Lash or ...YouTubeStart of suggested clipEnd of suggested clipI can turn it into something that I need. So in this case I'm going to use a barrel twist. I'm gonnaMoreI can turn it into something that I need. So in this case I'm going to use a barrel twist. I'm gonna use pliers. And I'm going to bend. The wire in this case the tag end around the main.
How to make a bead with wire?
Using either your fingers or another pair of pliers, grip the end of the wire and coil it tightly around the upright piece of wire below your loop, coiling from top to bottom. Keep coiling until your reach the top of your bead. Where the wire coil tail meets the bead, snip off the excess wire end with your wire cutters.
How to bend wire with a round nose plier?
Grab the wire with your round nose pliers just above the bend. Bend the wire up and over the top of your round nose pliers. We like the Xuron Jeweler's Super Fine Round Nose Pliers.
How to make a bead with a chain nose plier?
Place your bead (s) onto a head pin. Right after the bead, grab the head pin with your chain nose pliers and bend the wire at a 90-degree angle above the pliers. This creates a small upright piece of wire between the bead and the bend. One of our favorite chain nose pliers is the Beadsmith Jeweller's Micro Pliers.
How to tuck wire into wrapping?
Use chain nose pliers to tuck the end of the wire into your wrappings.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
What is soft wire used for?
Soft wire is used in very small work (such as wire knitting and for wrapping a larger gauge wire). Half hard wire is the most commonly used wire in jewelry making. It is easily manipulated and holds its shape well. "Hard" wire is rarely used. It is very difficult to bend and is hard on your tools.
What is the diameter of argenteum wire?
It is similar to Sterling but more resistant to tarnish. "Gauge": The diameter of most of the wire used in this tutorial is 22 gauge. The diameter of wire is referred to in terms of a gauge.
What is a crimping plier?
Crimping Pliers: Crimping pliers come in various sizes and are intended for the purpose of squeezing and crimping crimp tubes and beads. For the purpose of making the wrapped loop, they are really good for smoothing out burrs and to tighten down wire ends (described later in this tutorial). More Info About Pliers.
What are the jaws on a wire plier?
Some pliers have longer and wider jaws and more pointed tips than others. In the making of the wrapped loop, these pliers are used to grip and hold wire, to make bends and to burnish.
What is a flat nosed plier?
Flat Nosed Pliers: The jaws of flat nosed pliers are smooth and flat with sharp edges. Their tips are flat and squared off. Some pliers have longer and wider jaws than others. In the making of the wrapped loop, flat nosed pliers are used to make crisp edged bends and to grip and hold the wire.
What is round nose pliers used for?
In the making of the wrapped loop, round nose pliers are used to grasp wire, make curves, round shapes and soft bends.
What kind of pliers do you use for wrapping a loop?
There are many types of pliers. For the purpose of making the wrapped loop, we will use round nosed, flat nosed, and chain nosed pliers. Bent tipped pliers and crimping pliers are useful as well. Round Nosed Pliers: The jaws of round nosed pliers are smooth, rounded and tapered. The tips of the jaws are pointed.
How to improve muscle memory?
Tip 1: When learning to make wire wrapped loops, or any skill for that matter , you can improve your “muscle memory” by repeating the skill many times. How many times do you think you practiced each letter of the alphabet before you perfected your printing and writing skills? That same “practice makes perfect” adage works when learning new skills in wire work.
What do you need to learn to make jewelry?
Judy Says: When first learning to make jewelry, the first thing you need to learn to do well is make a wire wrapped loop. Learning how to make consistent wire wrapped loops will make you more comfortable and confident with working with wire when you go on to the next step/stage in your wire wrapping/weaving journey.
Can you wrap wire around pliers?
Note: You will notice in the tutorial photos that the winding wire was never let go and wire wrapped around the tip of the pliers. This is not the way to make a wire wrapped loop if you want to conserve wire, but it is easier for the beginner. When you get better at it, you will drop the wrap wire and change plier positions to wrap, using less wire.
What do you need to make wire chains?
If you love to make bead and wire chains but don’t happen to have one of those fancy looping pliers handy, don’t fret: you can learn how to effortlessly make perfect wire loops (almost) every time! All you need are a couple of pairs of pliers, a flush cutter, and a little bit of time to practice.
What to use if you don't have a pair of combination pliers?
If you don’t have a pair of combination pliers, you can use a pair of round nose pliers and a pair of chain nose pliers.
What is wire wrapped loop?
Wire wrapped loop is a basic technique that is widely used in jewelry DIY. Make sure you nail this one!
What is a loop in jewelry?
The loop serves as a connection in your jewelry. You can add a bead, a chain, or even another loop to it.
How to wrap a pendant with a chain?
OPTIONAL: Open the loop slightly and slide on the loop of your pendant or charm; close the loop. Grip across the loop with a pair of chain-nose pliers. Grasp the tip of the wire with chain-nose pliers and wrap it around the straight length of wire above the pendant , making approximately three tightly-wound wraps.
How to make a loop on a wire?
Forming the first loop: Hold a pair of round-nose pliers so the jaws are horizontal. Grip the wire with the tips of the pliers, about 1-1/2 inches down from one end of the wire. With your free hand, bend the top of the wire to form a 90 degree angle.
How to make a pliers angled?
Place the pliers into the angled section , vertically, so one barrel is above and one is below the wire. Bring the wire up and over the top barrel of the pliers so it is now facing down at an angle .
How to grip a chain?
Grip across the loop with your chain-nose pliers. (If you've attached this loop to a chain, be careful not to grip the chain at the same time as you grip the wire.)
How to attach a charm to a soldered chain?
Use the double wrapped-loop technique to attach a pendant or charm to a soldered loop on a chain for a secure finish. Link double wrapped loops together to create your own chain then finish with your choice of clasp.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
How to make a bead with wire?
Using either your fingers or another pair of pliers, grip the end of the wire and coil it tightly around the upright piece of wire below your loop, coiling from top to bottom. Keep coiling until your reach the top of your bead. Where the wire coil tail meets the bead, snip off the excess wire end with your wire cutters.
How to bend wire with a round nose plier?
Grab the wire with your round nose pliers just above the bend. Bend the wire up and over the top of your round nose pliers. We like the Xuron Jeweler's Super Fine Round Nose Pliers.
How to make a bead with a chain nose plier?
Place your bead (s) onto a head pin. Right after the bead, grab the head pin with your chain nose pliers and bend the wire at a 90-degree angle above the pliers. This creates a small upright piece of wire between the bead and the bend. One of our favorite chain nose pliers is the Beadsmith Jeweller's Micro Pliers.
How to tuck wire into wrapping?
Use chain nose pliers to tuck the end of the wire into your wrappings.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
