Wire Wrapped & Beaded Earrings
- Step 1: Cut and Curl Wires After donning your safety glasses, use a pair of flat-nosed pliers to gently straighten a section of your heavier wire from the spool. ...
- Step 2: String Beads and Begin Wrap Use pliers and your fingers to shape the wires into teardrop shape. ...
- Step 3: Incorporate Beads ...
- Step 4: Finish Up With Jump Rings ...
- Step 5: You Did It!
How to make beaded earrings with wire?
Wire Wrapped & Beaded Earrings
- Cut and Curl Wires. After donning your safety glasses, use a pair of flat-nosed pliers to gently straighten a section of your heavier wire from the spool.
- String Beads and Begin Wrap. Use pliers and your fingers to shape the wires into teardrop shape. ...
- Incorporate Beads. ...
- Finish Up With Jump Rings. ...
- You Did It!
How to crochet jewelry with wire and beads?
Method 2 Method 2 of 3: Simple Ring Download Article
- Choose a 26-gauge beading wire in the finish you prefer. Go with 26-gauge beading wire since it's nice and malleable.
- Unwind several inches of wire and create a slip knot. Leave the wire on the spool as you work! ...
- Create 3 basic chain stitches to start the ring. ...
- Single crochet into each chain. ...
How to make bead ear threaders earrings?
- Hold the hoop wrong side up. ...
- Work 1 sc (single crochet), slide one bead up against the sc, and chain 1.
- Repeat step 2 all around the whole hoop.
- After the last chain 1, do 1 slip stitch around the hoop.
- Cut the thread loop and, using the chenille needle, thread the end under a few crochet stitches.
How to string beads with beading wire?
Selecting Beading Wire
- Decide on several strands. ...
- Decide which diameter fits through your bead holes. ...
- Consider whether pound test strength is an important factor in your project. ...
- Bead stringing wire is mostly meant to be secured using crimp beads or tubes. ...
How to make a bead with wire?
How to wrap wire around pin?
How to wrap a pin tail?
About this website
How do you make wire wrapped beads?
1:119:36Beaded Chain Link Wire Wrap Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's kind of hard to tell it's easier just to make your first one and then see how it works outMoreIt's kind of hard to tell it's easier just to make your first one and then see how it works out because you need the space here for the bead.
How do you make wire earrings?
5:127:46How to Make Wire Earrings | Jewelry 101 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBack towards yourself and then pull the wire down. And around the plier into my circle. Now you canMoreBack towards yourself and then pull the wire down. And around the plier into my circle. Now you can see that circle is right on top of the bead.
What do I need to make wire wrapped jewelry?
Basic Wire Wrapping SuppliesRuler.Wire Cutters.Permanent Marker.Jewelry Making Pliers: Round, bent nose and chain (use these to tuck in wire ends and shape your wire)Gauge (measures the inside of holes for beads and the width of the wire for gauging)Needle Nose Flat File (for filing the wire ends)More items...•
How do you wrap earrings?
1:039:02Quick Wire Wrapped Earrings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put a Center on what will be the front of the earring. Then we take one of the sides right theMoreAnd put a Center on what will be the front of the earring. Then we take one of the sides right the way around the back into the front again and do the same with the other.
What kind of wire is best for wire wrapping jewelry?
24-gauge wire is fine enough to fit through most gemstone beads, and is durable enough to make good wire-wrapped loops. 22 gauge jewelry wire is a good general-purpose wire gauge.
How do you twist earrings to make wire?
1:543:48How to Do a Basic Wire Twist - YouTubeYouTubeStart of suggested clipEnd of suggested clipI go around the first complete succession around sets you up for the next two to three and you wantMoreI go around the first complete succession around sets you up for the next two to three and you want to make sure that it finds its home which is the 90 degree angle.
How do you make wire jewelry step by step?
3 Steps to Making Wire Wrapped JewelryStep 1: Create the Base of the Pendant. Cut the wire. ... Step 2: Wrap and Twist the Protruding Wires. In step 1, the goal was to create a base with a number of protruding wires. ... Step 3: Wrap the Stone. Wrap, twist, and bend the wires around the stone to keep it in place.
How do you start a wire wrap?
0:1310:22How to Start Wire Wrapping : Essential Tools Explained - YouTubeYouTubeStart of suggested clipEnd of suggested clipStarting tools you'll need to get into wire wraps joy making on this tutorial will focusMoreStarting tools you'll need to get into wire wraps joy making on this tutorial will focus specifically. On making jewelry out of wire. Rather than other techniques such as beatings.
How do you make wire wraps?
1:1914:47Quick Beginner Wire Warp Basic Pendant Undrilled Stone Cab ...YouTubeStart of suggested clipEnd of suggested clipAnd once you wrap it. And once you can actually just twist. Hold on one second I'll just pinch thisMoreAnd once you wrap it. And once you can actually just twist. Hold on one second I'll just pinch this first okay pinch it it kind of holds together better. So you can just kind of turn.
How do you make shrink wrap earrings?
2:4411:01DIY How to Make Your Own Earrings | Shrink Plastic Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure your oven is set to 350. Because you're gonna want to make sure you leave this in the ovenMoreMake sure your oven is set to 350. Because you're gonna want to make sure you leave this in the oven. Long enough so that way it does the the shrinking process and flattens out as it's in the heat.
How do you wrap wire around jewelry?
6:017:38Basic Basket Wrap Tutorial for Wire-Wrapped Jewelry and PendantsYouTubeStart of suggested clipEnd of suggested clipRight here. And wrap this away from us and back towards us coming up under the round nose plier orMoreRight here. And wrap this away from us and back towards us coming up under the round nose plier or bail making pliers. And then just twist this around. Itself. Until you get your desired fullness.
How do you make bead earrings?
0:052:38How to Make Beaded Fringe Earrings | Jewelry Making | MichaelsYouTubeStart of suggested clipEnd of suggested clipAnd today we're going to make beaded fringe earrings with a bead woven. Top. So to make theseMoreAnd today we're going to make beaded fringe earrings with a bead woven. Top. So to make these earrings you're going to need beads pliers scissors beading thread ear wires wire guards a beading needle.
How do you make wire jewelry step by step?
3 Steps to Making Wire Wrapped JewelryStep 1: Create the Base of the Pendant. Cut the wire. ... Step 2: Wrap and Twist the Protruding Wires. In step 1, the goal was to create a base with a number of protruding wires. ... Step 3: Wrap the Stone. Wrap, twist, and bend the wires around the stone to keep it in place.
How do you make simple wire hoop earrings?
1:2011:53Making Simple Wire Hoops | Jewelry 101 - YouTubeYouTubeStart of suggested clipEnd of suggested clipI am going to use my ring mandrel to shape this pick this wire into a hoop the reason I like to useMoreI am going to use my ring mandrel to shape this pick this wire into a hoop the reason I like to use a ring mandrel is because they're marked with different sizes.
How do you make metal wire earrings?
1:4413:26How to Form Shapes Out of Wire | Jewelry 101 - YouTubeYouTubeStart of suggested clipEnd of suggested clipA perfect circle I could try but it's not gonna be very pretty. So it's great to use something likeMoreA perfect circle I could try but it's not gonna be very pretty. So it's great to use something like this to form your shape and also these are fun because they're graduated.
How do you make homemade earrings step by step?
0:002:13How to Make Your Own Earrings | Crafting Quick Tips | MichaelsYouTubeStart of suggested clipEnd of suggested clipOnce you slide the bead on the head pin. You want to make sure that you have about a quarter of anMoreOnce you slide the bead on the head pin. You want to make sure that you have about a quarter of an inch of wire left so this one we're going to trim down just a hair using wire cutters.
How to straighten a wire for earrings?
After donning your safety glasses, use a pair of flat-nosed pliers to gently straighten a section of your heavier wire from the spool. As an alternative method of straightening your wire, place it on a bench block and rap on it gently with a rawhide mallet. Line up the straight wire with a small ruler and use your flush snips to cut two 4 inch (10cm) pieces of wire. The length of these wire determines the overall size of the earrings, so feel free to experiment but make sure the two wires match.
How to wrap a wire around a wire?
Slide one bead down its wire until it reaches the larger wire loop. Hold the bead in place at the inside of the loop with one hand , and wrap the wire around the larger wire twice, repositioning the slack to dodge the other end of the wire as necessary. I like to do this wrapping with my fingers, but you may find pliers to be helpful or more comfortable.
What pliers do you need to make wire jewelry?
A dedicated set of jewelry pliers is essential for making jewelry with wire. Make sure you have two sets of smooth-jawed needle nose pliers, a set of round nose, and a set of flush snips.
How many times should I wrap a teardrop?
Lay the unkinked wire end across the teardrop shape (near an end loop as shown) and wrap it five or six times with the help of some pliers. I like to wrap clockwise, but you may prefer counterclockwise. It's important that you wrap the same direction throughout, so stick with whichever wrapping direction you pick.
How many beads are needed for earring?
For each earring, you'll need a 4 inch (10cm) piece of your larger gauge wire, about an arm's length of the wrapping wire, seven beads, three jump rings, and one ear wire. The wire used here is silver plated, which is affordable enough to encourage experimentation. However, due to many people's skin sensitivities, sterling silver ear wires are recommended.
How to close jump rings?
Open a third jump ring and use it to hook both of your previous jump rings. Also slide on an ear wire, and carefully use two pairs of pliers to close the last jump ring.
How to close a gap in a wire?
If the wire doesn't quite reach to meet itself, reposition your grasp and apply gentle twisting pressure to close the gap.
What to put on hoop earrings?
With a little bit of practice, your earrings will rival ones sold in upscale boutiques. Round crystal beads are another great choice to add to hoop earrings.
What stitch is used on earrings?
The top portion of the earrings is a standard brick stitch with a decrease to make the familiar triangle shape. Using a larger bead for this portion will also cut your bead stitching time.
What to use instead of brick stitch earrings?
This twist on classic brick stitch earrings makes it more contemporary and much faster to make. Substitute the beaded tassels with cut pieces of chain and your earrings will shine while they swing and be just a little faster to make.
What are peyote beads?
Peyote tube beads are a great way to use leftover beads and the skies the limit when it comes to patterns . You'll be amazed at how many different patterns you can come up with for these little beads.
Can you make jewelry with spare time?
One of the best things is you can make components anytime you have some spare time and connect them later to make finished jewelry. Elaborate results that are easily achieved with little portions of beading time.
Can you make earrings with off loom beads?
Not only can this list help you out with a last-minute gift, but it's also a great go-to when you want to learn or practice a new beadwork or jewelry making technique.
Step 1: Prepare your jewelry wire
For this wire wrapped earrings tutorial, we’d recommend taking your 0.8mm wire and cutting it to a length of approximately 24mm.
Step 2: Thread your bead and start wrapping!
Thread your silver wire through the hole in your chosen bead, making sure that you leave some extra wire (approx. 50mm) poking out of the top of your bead to attach your ear hook later.
Step 4: Cut and neaten your jewelry wire
Once you’re happy with the position and look of the three loops that are wrapped around the base of the top piece of wire, you can snip the excess wire off with your wire cutters.
Step 5: Create a small loop at the base of the wire
Just above those three loops you’ve created, you can now make a small loop.
Step 6: Add your earrings findings
Now you’ve made the main part of your wire wrapped earrings with these 6 Easy Steps To Make Wire Wrapped Earrings; you can finish the design with a jump ring and an earring hook of your choice.
Step 1: twist the basic wire pattern of the hoop earrings
1st, cut off a long piece of 1.5mm gold aluminum wire, then twist the wire for four circles (as shown in the picture); 2nd, slide a 4mm white glass pearl bead onto the copper wire, then fix one end of the wire onto the aluminum wire pattern; 3rd, add another three pearl beads onto the wire, then wrap the wire onto the aluminum wire pattern and cut off the extra wire (as shown in the picture)..
Step 2: add more beads onto the wire pattern
1st, cut off another piece of 1.5mm aluminum wire, then twist the wire for loops at two ends; 2nd, attach this small wire pattern inside the bigger wire pattern and fix them with 0.5mm copper jewelry wire; 3rd, slide two 6mm rose quartz beads onto the jewelry wire and wrap the wire around the aluminum wire pattern, then cut off the extra wire.
Step 3: finish the wire and beads hoop earrings
1st, hang a gemstone pendant onto the bottom of the wire pattern; 2nd, slide three 6mm orangered jade beads onto the jewelry wire, then wrap the wire and fix the pattern together to finish the hoop earring making.
How to make a beaded earring?
1st, slide a 10mm glass pearl bead and a brass bead cap onto a brass headpin ;#N#2nd, attach this beaded dangle onto the bottom loop of the wire pattern by twisting the wires together;#N#3rd, make another same earring with the same steps.
How to make a rhinestone necklace?
1st, cut off a long piece of 0.3mm copper jewelry and slide five 6mm white glass beads onto the wire;#N#2nd, cross the two ends of the wire through the fifth glass bead;#N#3rd, slide a gold 6x6x5mm acrylic rhinestone montee bead onto the wire and put it onto the center of the beaded pattern then fix them together.
How to make a crystal head pin?
1. Slide a small bead cap, a crystal rondelle, a large bead cap, and a silver bead onto a head pin. 2. Grip the headpin wire just above the beads with the round-nose pliers. Bend the wire over the pliers 90 degrees. Reposition the pliers, gripping the wire at the 90-degree bend. Grab the end of the wire with your fingers and wrap it around ...
How to make a loop with pliers?
Grab the end of the wire with your fingers and wrap it around the pliers to make a partial loop, using the pliers like a mandrel. Shift the pliers again and continue wrapping the wire around the pliers to form a loop.
How to make a loop with a round nose plier?
3. Grasp the loop flat in the jaws of the chain-nose pliers. Without moving the pliers, grab the end of the wire with your fingers and wrap it twice around the neck of the headpin .
How to make a bead with wire?
Once you’ve wrapped the top portion of the bead, snip your wire so that you have about four inches of wire left. Make a small loop at the end of that tail and use your chain nose pliers to coil the wire inward, toward the bead. Keep your coil nice and tight.
How to wrap wire around pin?
Trim that with your wire cutters, so that all the wire is flush against the pin. Next, begin wrapping your 24-gauge wire around the pin more or less where your wrapped pin work ends. Keep wrapping as the pin transitions to the bead. Wrap the wire away from your body, keeping the wire close against the previous wrap and snug to the bead.
How to wrap a pin tail?
Hold the eye of the pin firmly with your chain nose pliers, and begin to wrap the tail away from you. It should look something like what you see here (different bead pictured). You should be able to go two or three times around. You’ll have a small bit of wire sticking out when you are at the end of wrapping your tail.
