You can find out how much carpet you need for your staircase as follows:
- Figure out how many stairs are there on your staircase and write down the number on a piece of paper.
- Take a separate count of the number of winders because they’re sized differently.
- Measure one stair by running the tape over the tread and riser. Also, make sure that you measure the width of the stair at the widest points.
How to measure stairs?
When measuring a landing area for carpet, it’s important to note that measurements will need to include the top step?
How to measure a standard room?
How much to add to a carpet?
How to measure a hallway?
How to measure a mid landing?
When measuring your room for carpet, is it important to include alcoves, doorways and recesses in?
See 4 more
About this website
How do I measure how much carpet I need for stairs?
HOW TO MEASURE FOR STAIRSMeasure tread (1) + riser (2) The tread is the part you step on. ... Count the number of steps! Multiply your first number by the number of steps you have to cover: e.g. 20cm + 20cm = 40cm x 12 steps = 4.8m (This is your LENGTH)Measure the width (3)
How much carpet do I need for 12 stairs UK?
Based on a straight set of stairs with 12 steps you'd roughly need 6m x 90cm (19.7' x 3').
How much carpet do I need for 14 Steps UK?
Multiply 648 by 14, which is the total number of stairs. The answer is 9072 square inches. The square inches equate to 63 square feet of carpet size.
How do I work out the square Metres of stairs for carpet?
0:482:19Designer Carpet Measuring Videos 2 - How To Measure Stairs - YouTubeYouTubeStart of suggested clipEnd of suggested clipTimes 14 gives us a total length of 6.0. 2 meters carpets can be fitted in strips. So you won't needMoreTimes 14 gives us a total length of 6.0. 2 meters carpets can be fitted in strips. So you won't need that full length. Instead you can use this process the width of the stairs is 68 centimeters
How much does it cost to carpet 13 stairs?
Carpet installation costLocationAverage cost to install1,000 sq. ft. house*$1,100 – $4,5001,500 sq. ft. house*$1,600 – $6,7002,000 sq. ft. house*$2,100 – $9,000Flight of 13 stairs$150 – $6008 more rows•Aug 18, 2021
How much does it cost to carpet 14 stairs?
Count how many steps your flight of stairs has. Say, 14 steps. Calculate your needed carpet length by substituting these measurements in this formula: length = riser rise × number of steps + tread run × (number of steps - 1) . That is length = 10 inches × 14 + 12 inches × (14 - 1) = 296 inches .
How much carpet do I need for 13 stairs in meters?
For example, if you have a staircase with 13 steps and 1.2 metres by 1.2 metres landing, you will need to calculate the total square metre coverage of the stairs and add this to the total square metre coverage of the landing to get your total - you would be looking at 10 square metres of carpet.
How much does it cost to carpet a standard staircase?
For a typical set of 12 box stairs, you'll multiply the 36” width by the 18” tread and riser, then multiply by 12 stairs. The total is 7776 square inches of carpet, which equates to 54 square feet. Simple enough, right?
How many meters is a standard staircase?
To stay within Building Regulations, a domestic staircase needs a rise of between 190mm and 220mm. Standard risers are around 200mm, so aim for this. The average rise is 2,600mm, which divides easily into 13 200mm risers, or steps.
How do you calculate stairs in meters?
Divide the overall change in level (overall rise) by 150mm.450mm / 150mm = 3. This tells us that with a riser of 150mm we will need 3 risers/steps. ... 450mm / 2 = 225mm. ... Twice the Rise plus the Going (2R + G) should be between 550mm and 700mm. ... 2 x 150mm + 275mm = 575mm.
How do you measure stairs UK?
Your going needs to be measured horizontally (not diagonally). Your stairwell could also restrict your head height, bear in mind that you need to have at least 2 metres of headroom throughout the staircase, measured along the diagonal pitch line (from nosing to nosing).
How do you calculate area of stairs?
2:074:38Calculating area of stairs - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe equation or the formula that we put in is equal some open brackets be 8 + B 9 and then close theMoreThe equation or the formula that we put in is equal some open brackets be 8 + B 9 and then close the brackets to calculate the area of this step. That's length times the width.
How much carpet do I need for 12 stairs?
For a typical set of 12 box stairs, you'll multiply the 36” width by the 18” tread and riser, then multiply by 12 stairs. The total is 7776 square inches of carpet, which equates to 54 square feet.
How much carpet do I need for 11 stairs?
Multiply the square footage of 1 step—the number you just calculated—by the total number of steps. This is the total area, or square footage, for the stairs you plan to carpet. Say that you'll be carpeting 12 stairs. In our example, you'd need a total of 96 square feet (8.9 m2) of carpeting to cover your stairs.
How many square Metres are my stairs?
To do this, measure the width and length of your room using a tape measure. Then multiply the width by the length to get the area in square feet. So 12 x 12 is 144 square feet. Then multiply your figure by 0.09290304 to calculate the square metre.
How long of a runner do I need for 13 stairs?
Multiply the number of steps by the total inches per stair. Then divide by 12 to get the total linear feet necessary for your straight stairs. We recommend adding one extra foot of runner length to your total, just to be safe.
How much carpet do I need for a stairs? — MoneySavingExpert Forum
I don't know if this is a silly question but is there a standard amount of carpet you need for a staircase? It is a 13 step staircase and that's all I really know and I am trying to work out how much carpet I will need.
Carpet: Measuring & Fitting – Online Carpets
a. We advise you to use a pipe and cable detector to locate their positions and mark them on the floor so you can avoid them. b. Grippers should be fitted around the edges of your room except for the threshold of your door, you will require a door bar for this area.
How to measure stairs?
Measuring Stairs. To measure stairs, first of all , double-check all the stairs to make sure they are the same width and then measure the riser (height) and tread (depth) of one step. – This is the length vertically up and over the step. Multiply that measurement by the number of stairs that you have (providing they are all the same type of shape).
When measuring a landing area for carpet, it’s important to note that measurements will need to include the top step?
When measuring a landing area for carpet, it’s important to note that measurements will need to include the top step of the stairs as well as the landing. The inclusion of the top step is so that the landing carpet flows over the top step and seamlessly into the stairs once fitted .
How to measure a standard room?
If your room is rectangular or square, measuring it is straightforward; You will need to measure the length and width of the room at the widest point (including going into doorway areas) and multiply the two measurements to calculate the size of the floor surface.
How much to add to a carpet?
Always add 10 centimetres to your total length and width measurements. This will allow for any deviations in the wall, and the cutting of your carpet when it is fitted. Be careful as a lot of rooms are not square, so even allowing 10cm might not be enough.
How to measure a hallway?
In the absence of awkward L shaped, T shaped or inverted halls, we suggest you measure a hallway as you would a standard room, by recording the width and length and taking into account any alcoves or recesses.
How to measure a mid landing?
Measuring a Mid-Landing. You should measure a mid-landing as you would a normal landing area. Your mid-landing carpet must fit over the top step (benneath)in one piece; so you’ll need to measure the mid-landing width and length as well as the height and width of the top step. Always add 10 centimetres to your total length and width measurements.
When measuring your room for carpet, is it important to include alcoves, doorways and recesses in?
When it comes to measuring your room for carpet, it is crucial to include alcoves, doorways and recesses in the calculation. Sometimes people overlook one or all of these, which leads to mistakes about how much carpet is needed.
What direction do you put carpet on stairs?
Direction of the Pile. The carpet on stairs must run in the same direction on every stair, and the direction of the pile must go with the flow of traffic -- from top to bottom, not from side to side. This means that, in order to work with the size of a roll of carpet, not all of the stairs are installed in one piece.
How many stairs are there in a carpet set?
Commonly, a staircase leading from the main floor to the second floor of a house will have 13 stairs, ...
How wide is a grand staircase?
Measure the stair to determine the width -- in grand staircases, it could be quite wide. You will require a piece of carpet that is the width of the stair plus a few extra inches to wrap around the outer edge of the tread, by 18".
How many stairs are there in a 12x18 carpet?
For a typical set of 12 box stairs measuring 3' wide, using a carpet that is 12' wide, you would require 12' x 4'6" (in a 12' width of carpet, you get 4 box stairs -- 12' divided by 3' -- so every 12' x 18" gives you 4 stairs).
What is a stair that has one open side with railing posts on it called?
A stair that has one open side with railing posts on it is known as a cap stair.
Where is the bullnose stair?
A bullnose stair is often found at the bottom of a staircase. It is wider than the rest of the stairs and is rounded on one or both sides. The tread and riser combined have the same measurements as a box stair (18"). Measure the stair to determine the width -- in grand staircases, it could be quite wide. You will require a piece of carpet that is ...
What is a box stair?
A box stair is straight, has no railing posts, and is closed in on all sides.
1. Preparing the Stairs
You need accurate measurements of the floor area you’re covering with your new carpet. To get that, you must measure the bare stairs themselves.
2. Measuring a Tread
The first step to finding out exactly how much carpet you need for your stairs involves measuring each tread. The tread is the flat horizontal part of each step, which you stand on when using the stairs. Use a tape measure, take an accurate measurement of the width and depth of the tread.
3. Measuring a Riser
Your next step is to measure a riser on your staircase. The riser is the vertical part of each step. You need to measure the height and width of the riser.
4. Measuring Landings
If your staircase has a small landing part-way up, your carpet will need to cover this too. Take accurate measurements of the width and depth of the landing. Note these figures on your piece of paper and also include the same rounded up measurements as before. Multiply the width of the landing by the depth to find its total area.
5. Calculating Area
You now have all the measurements you need to calculate the total area which your stair carpet needs to cover. First, you need to add your measurement for the depth of a tread to that of the height of a riser. Then, multiply that figure by the width of the tread and riser (which should be the same). You’ve now got the total area of one step.
6. Repeat Steps 2 to 5
You’ll now want to work through steps two to five in their entirety for a second time. Once you have, check all of your recorded measurements (exact and rounded) against your first set. You want each and every measurement to match. This is the only foolproof way to discover if you made a mistake anywhere along the way.
7. Get Cutting and Fitting
Once you’re sure of your measurements, you can start cutting your carpet. It’s best to use your rounded-up figures and then add around another 2.5cm for each step.
How to measure carpet for stairs?
In general, you can measure stairs for carpeting by using the equation width x ( (run + rise + nose) x number of stairs) = area . However, calculating how much carpet you need varies based on the stair type, shape, and size, as well as the configuration of your staircase.
How to calculate carpet needed for stairs?
Find the tread and riser measurements, adding them together. Multiply by your number of stairs for the total carpet needed for your stairs. Remember to exclude the top step unless your carpet running continues across the floor.
How is Standard Carpet Sold?
Carpet rolls come in two standard widths: 12 and 15-foot-wide rolls. You may also be able to find uncommon roll sizes, like 13.5-feet-wide. One square foot of carpet is a foot long by a foot wide, so there are nine square feet in a square yard of carpet.
How Much Padding Do I Need?
It protects the bottom of the carpet and prolongs its lifespan. However, you probably won’t install padding in humid regions or rooms like a basement. The padding type also depends on your needs .
How Much Carpet Do You Need to Repair Tears or Pet Damage?
If the carpet on your stairs needs repair, whether from pet damage or tears over time, replace the area. Measure the entire damaged area, avoiding the seams. A 4-inch incision in the middle of a step would require enough carpet to stretch the whole stair or the next available hem, for example.
Why do you put padding on stairs?
Padding allows the carpet to last longer on a staircase. It can also help absorb sound from squeaky stairs. When you install the padding on stairs, keep in mind that the padding is a couple of inches short from the wall to account for tack strips, holding the material in place.
How to count how many stairs to carpet?
Count to see how many stairs you plan to carpet. Multiply the number of stairs by the number from step 2 (the rise and run of your stairs). Round to the nearest foot.
How to measure the depth of a stair?
Turn your tape measure 90 degrees and measure the depth of the stairs. Hold the measuring tape flat against the tread of the stair, put the end of the measuring tape against the base of the next stair up, and stretch it out to the edge of the stair. Read the number at the very edge to get the depth and write it down to refer to later on.
How much to add to a staircase?
Add about 4 in (10 cm) to the length as a safety net. This will give you a little wiggle room for minute errors in your measurements or irregularities in the stairs. Add more than 4 in (10 cm) if you want to be extra-careful or know that your staircase is a bit odd (such as a staircase in a very old house that has warped with time).
What is tread on stairs?
The tread of a stair is the part that you step on when walking up and down the stairs. Think of the depth as how much room for your foot there is from heel to toe on the stair. Again, do this for 2-3 stairs and use the larger number for the depth of the stairs if there are any differences. ...
How to measure the length of a landing?
Use your tape measure to find the length of the landing. Turn your tape measure 90 degrees and measure from the baseboard where the landing meets the wall to the top edge of the stairs that continue down. Write down the length of the landing.
Is the rise a horizontal or vertical measurement?
The rise is a vertical measurement, and the depth is a horizontal measurement. Do this at least 2 times to make sure you are getting the right number for the rise. Use the bigger number if there are any variations. Tip: Some stairs have “nosing” (an edge that sticks out a bit).
How to measure stairs?
Measuring Stairs. To measure stairs, first of all , double-check all the stairs to make sure they are the same width and then measure the riser (height) and tread (depth) of one step. – This is the length vertically up and over the step. Multiply that measurement by the number of stairs that you have (providing they are all the same type of shape).
When measuring a landing area for carpet, it’s important to note that measurements will need to include the top step?
When measuring a landing area for carpet, it’s important to note that measurements will need to include the top step of the stairs as well as the landing. The inclusion of the top step is so that the landing carpet flows over the top step and seamlessly into the stairs once fitted .
How to measure a standard room?
If your room is rectangular or square, measuring it is straightforward; You will need to measure the length and width of the room at the widest point (including going into doorway areas) and multiply the two measurements to calculate the size of the floor surface.
How much to add to a carpet?
Always add 10 centimetres to your total length and width measurements. This will allow for any deviations in the wall, and the cutting of your carpet when it is fitted. Be careful as a lot of rooms are not square, so even allowing 10cm might not be enough.
How to measure a hallway?
In the absence of awkward L shaped, T shaped or inverted halls, we suggest you measure a hallway as you would a standard room, by recording the width and length and taking into account any alcoves or recesses.
How to measure a mid landing?
Measuring a Mid-Landing. You should measure a mid-landing as you would a normal landing area. Your mid-landing carpet must fit over the top step (benneath)in one piece; so you’ll need to measure the mid-landing width and length as well as the height and width of the top step. Always add 10 centimetres to your total length and width measurements.
When measuring your room for carpet, is it important to include alcoves, doorways and recesses in?
When it comes to measuring your room for carpet, it is crucial to include alcoves, doorways and recesses in the calculation. Sometimes people overlook one or all of these, which leads to mistakes about how much carpet is needed.
