- Get the proper fasteners. If you have the wood wall studs, traditional lag bolts or screws are ideal fasteners. ...
- Place the metal studs. Locating the exact center of the stud is essential. ...
- Find out where you are going to install your TV. You may typically prefer to have your TV side-to-side on the wall at a certain height and spot. ...
- Drilling the holes. We suggest that you need a 1/2′′ opening in the wall for most of the fasteners. ...
- Insert the Snap Toggle. Because the metal studs are vertically mounted, you’ll also want to vertically place your toggle bolt.
- Finally, mount the brackets. You’re nearly there. Simply mount the bracket to your wall now. Any metal washers (which normally come with your TV wall mount) will also be required.
How do I Mount TV to wall without studs?
Step 3: Choose the TV mount
- The fixed wall mount This mount places the TV close to the wall without sticking it out.
- A tilting wall mount It will allow you to tilt your TV screen up or down while fixed to the wall.
- Articulating wall mount
How to Mount TV on the wall without studs?
Part 3 Part 3 of 3: Connecting Your Hardware Download Article
- Screw the vertical brackets from the mount onto the back of your TV. ...
- Secure the brackets to the mount on the wall. Look for the clips or hooks on the bracket that attach to the mount on your wall.
- Plug the TV’s power cord into the upper power extender receptacle. ...
- Use the extension cable to plug the lower receptacle into an existing outlet. ...
How to find studs in wall for TV Mount?
How to Find a Wall Stud with 7 Easy Methods
- Use a Stud Finder. Zstock – stock.adobe.com Using an electronic stud finder is the most reliable way to locate a stud behind drywall and make a classic dad joke ...
- Knock on the Wall with Your Knuckles. No, this is not an amazing joke like the one above. ...
- Locate Your Switches and Outlets. ...
- Investigate Around Your Windows. ...
Which TV wall mounts are the best to buy?
Shopping: The Best TV Wall Mounts for Every Screen Size and Home Theater Setup
- Mounting Dream TV Mount Bracket. BEST FOR 42- TO 70-INCH TVS UP TO 110 LBS. ...
- USX Mount Low Profile Tilting TV Wall Mount. BEST LOW-PROFILE MOUNT FOR TVS UP TO 99 LBS. ...
- Pipishell Full Motion TV Monitor Wall Mount Bracket. ...
- Perlesmith Tilting TV Wall Mount Bracket. ...
- Pipishell Full Motion Dual Swivel TV Wall Mount Bracket. ...
Can you put a TV mount on metal studs?
Most TV mounts in the market are designed to be installed in either wooden studs or concrete, but it's also possible to mount a TV into metal studs. The process is virtually the same, but you will need a few additional tools and equipment.
How do you hang a heavy TV on metal studs?
0:176:00How to Wall Mount a TV to Metal Studs - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlright so there's three main fasteners that you can use to actually mount something a significantMoreAlright so there's three main fasteners that you can use to actually mount something a significant weight to a metal stud. And the first one my preferred method is actually called a drill or toggle.
Can you mount things on metal studs?
In order to hang items that need more support, it is possible to drill through metal studs. Titanium or cobalt drill bits are best suited for boring through metal. Once you've drilled your pilot holes, you'll want to use a toggle bolt to safely secure heavy items to the metal stud.
How do you mount a 65 inch TV to metal studs?
0:298:24How Install a TV MOUNT into a STEEL STUD WALL | Kanto ExplainsYouTubeStart of suggested clipEnd of suggested clipBut today we're going to show you how easy it is to mount your tv into steel studs. For the mostMoreBut today we're going to show you how easy it is to mount your tv into steel studs. For the most part installing a mount into steel studs requires the exact same tools as you would need to install
How much weight can metal studs hold?
The axial load, or load weight limit, for metal studs varies widely. An 8-foot, 3-1/2-inch metal stud, for instance, may support over 2,000 pounds, while a 16-foot stud of the same width will support as little as 400 pounds.
Are metal studs load bearing?
Heavier gauge metal studs are used in load bearing walls and structural applications such as exterior walls. Lighter gauge metal studs are used in non-load bearing applications such as some interior walls, half-walls, and partitions.
What screws do I use for metal studs?
Don't use drywall screws to screw your studs together—they're not designed for that. Pan-head framing screws work best. Concrete screws work great to attach the bottom track to the floor. And be sure you use fine-threaded drywall screws to hang the drywall.
How far apart are metal studs?
Most wall studs are spaced 16 inches apart on center; however, they can also be spaced at 24 inches. That said, spacing isn't always exact. Studs can bow and twist up to 1 inch in either direction as a home settles.
How do you drill through metal studs in drywall?
Find the Edge, Then the Center Use a small drill bit, or even a finish nail inserted into a drill/driver, to drill holes in the drywall on each side of the stud to pinpoint the edges. It may require punching a few holes to accomplish it -- you can patch them later with caulk or even toothpaste.
How wide is a metal stud?
It’s important that you find the EXACT CENTER of the stud. Metal studs aren’t very wide (typically about 1.25″). Since you will be drilling a 1/2″ hole in the stud, that only leaves about 3/8″ of metal on either side of the whole.
How much metal do I need to drill holes in wall mounts?
For most of the fasteners I recommend, you’ll need a 1/2″ hole in the wall. So, you’ll need a 1/2″ metal drill bit to drill those holes. Click here to see a metal drill bit. Make sure you’ve taken care to plan the position of your wall mount. Also be careful and don’t let the dill bit “walk” around while you’re trying to drill through the metal.
Can you mount a TV on a metal stud?
Unlike wood studs where you can simply drive lag bolts or screws straight into the 2×4 studs, metal studs are hallow and have thin walls. There simply isn’t enough material for the threads to grab securely.
Do you need to position toggle bolts vertically?
Since the metal studs are installed vertically, you’ll want to position your toggle bolt vertically as well. Otherwise the toggle bolt will run into the side of the metal stud and the connection will be all funky and not as robust.
How to Find Metal Studs in Your Wall
You can find your metal studs with a stud finder. Most apartment buildings and office spaces have metal studded walls for fire safety. Steel studs are not flammable and they help to slow the spread of fire. They are also resistant to damage from termites, insects, rot, and mold – which makes them popular in a lot of modern buildings.
Tools For Mounting a TV Into Metal Studs
A TV mount that is designed for metal studs is almost identical to the one designed for a wooden stud installation. The difference lies between the hardware that is used to attach the bracket to the wall for proper support.
Step 1: Determining The Height for Your TV
The first step in the installation process is to figure out how high you want your TV to be. We recommend centering the TV at your eye level to ensure a comfortable viewing experience and avoid neck and eye strain.
Step 2: Installing the Hardware to the TV
The next step is to install the frame on the TV. Start by installing the vertical arms to the TV. We used a spacer here because there’s a ridge on the TV and a spacer brings the arm slightly out.
Step 3: Locating The Metal Studs in Your Wall
Use the stud finder to locate the metal studs and use a pencil to mark the areas. In most cases, metal studs are about 16 inches apart, so that should give you a good idea of where to start.
Step 4: Installing The Bracket
Next, we’ll be using the level to ensure that the marks are level. Once you’re sure that the marks are level, stick the template on the wall using painter’s tape.
Step 5: Installing The Toggler Bolts
The Kanto LX600SW TV Mount comes with 4 toggler bolts that are very easy to secure. You can turn the bolt so that it can be extended and inserted through the hole and then once it’s through, it can be turned so that it catches against the back of the stud.
