how do you mud a corner bead

Paper-faced metal corner bead

1. Coat the drywall corner with a thick-layer taping mud, covering the length of the corner.
2. Line the corner bead up with the corner’s center and press it firmly into the mud.
3. Using a corner roller tool, roll across the center of the corner bead to secure it to the wall and squeeze out excess mud.
4. Wipe away excess mud. ...

Full Answer

How to attach corner beads to Durock?

How to Attach Corner Beads to Durock

1. Measure the height of the wall where the corner bead will be installed. Record the measurement. ...
2. Cut along the line with a pair of tin snips. Snips cut just like scissors. ...
3. Line up the first cement board screw along the top of the corner bead. ...
4. Drill until the head of the screw is flush with the corner bead. ...

More items...

How to attach corner bead to drywall?

How to Install Paper-Faced Corner Bead

1. Cut the drywall paper beading with tin snips. If you need to cut pieces to length, simply hold the wall beading in place, mark the cut, and cut ...
2. Mud the corner. Spread a thick layer of all-purpose joint compound on both sides of the corner and smooth it off with a putty knife.
3. Mist the wall beading. ...
4. Position the drywall paper bead. ...
5. Embed the tape. ...

More items...

How to Spackle corner bead?

Start with spackling the nail and screw holes, then move on to the long horizontal joints, then the outside corners, and then finish with the inside corners. Make sure you allow enough time to dry in between coats. If the spackle is grey, it is still drying. Once it turns white, it is completely dry.

How to mud and tape drywall corners?

• Apply mud with the utility knife to both sides of an inside corner. Place a creased strip of paper drywall tape in the corner over the compound.
• Pull the utility knife along the tape, embedding it into the mud and pushing out air bubbles. ...
• Place strips of preformed tape on the outside corners and edges. ...
• Allow the mudded and taped areas to dry overnight. ...

What is the best way to mud corners?

1:312:29How to Mud and Tape Drywall Corners | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the trick is to make sure i feather this edge right down to zero. So i'm pushing really hard onMoreAnd the trick is to make sure i feather this edge right down to zero. So i'm pushing really hard on this side of the knife that will feather the joint compound. Right into the corner. Bring it right.

How do you mud a bead?

1:357:01The EASIEST way to coat CORNER BEAD! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay first thing you need to do is feather your edge so feathering your edge is done by bending theMoreOkay first thing you need to do is feather your edge so feathering your edge is done by bending the blade like this so i'm pushing really hard on the blade.

How do you mud inside a corner?

3:007:10HOW TO TAPE DRYWALL (INSIDE CORNERS) - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere. You want to make sure it's getting in all the gaps. Okay now I'm flattening it all outMoreHere. You want to make sure it's getting in all the gaps. Okay now I'm flattening it all out consistently. I do the same thing here one two flatten it all out consistently.

Should drywall corner bead be taped?

There is no need to put any tape on the corner bead (though you can tape the edge of metal corner bead to reduce corner cracking). In addition, there are usually no seams or gaps along the corner bead edge (if there are gaps, use joint tape).

Do you mud over corner bead?

The first coat of drywall mud should be applied to corner bead after the drywall taping has been done. The second coat can be done either after the seams have been taped and coated or after the seams have been final coated.

How do you finish corner bead without coat?

0:482:39NO-COAT® Product Spotlight Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply all purpose joint or taping compound to the drywall. Apply evenly to ensure adequate coverage.MoreApply all purpose joint or taping compound to the drywall. Apply evenly to ensure adequate coverage. For an easier and faster method use the certainty double barrel hopper to fill the corner bead.

How many times do you mud corners?

If your wall has distinct crevices, cracks, or textured areas, or if your brand of drywall mud isn't offering enough coverage, you may have to do a couple of additional coats of compound. However, in general, you'll need one coat to fill in the seams and three more coats after taping.

Do you use corner bead on inside corners?

You'll need beads for all outside corners, some inside corners, and occasionally to cover the edge of a panel. Beads for inside corners; Special tapes for inside corners provide excellent and long-lasting results. The one on top has a flexible center.

How do you finish inside corners on drywall?

Gather Tools and Supplies. For this project, you will need: ... Cut and Crease the Drywall Tape. ... Coat the Corners with Drywall Compound. ... Place the Tape in the Corner. ... Apply Additional Drywall Compound to One Side of the Corner. ... Apply Drywall Compound to the Other Side. ... Sand and Smooth.

Do you put mesh tape on corner bead?

Mechanically attach metal corner bead to the drywall or framing with staples or nails. Next put sticky mesh tape over the metal to drywall transition on each side, then fill will all purpose joint compound, let dry, then put lightweight joint compound over that.

Do you tape corners or joints first?

The order of taping is the same: Do screw indentations and beveled joints first, inside and outside corners next, and butt joints last.

Do you overlap drywall tape in corners?

DON'T overlap drywall tape. Applying a single layer of paper tape will help minimize any chance of ending up with a bulge in the finished wall.

What joints do you mud first?

The “first coat” consists of applying the mud-saturated tape to all of the joints and corner beads and filling screw or nail holes for the first time. Begin with the butt joints first, then the horizontal tapered joints, then the angles and finally, the corner beads.

How do you apply mud?

2:339:09Drywall mudding 101 - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou don't want to squeeze all the mud out from behind but you want to squeeze it out so it goes downMoreYou don't want to squeeze all the mud out from behind but you want to squeeze it out so it goes down. And i'll show you why you want to get it down some make sure you got my mud behind.

How do you mud a hole?

1:103:35DIY fill holes in Sheetrock - how to use mud joint compound - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt so when I applied the mud the mud will actually fill a hole. And it's easier to cover that holeMoreIt so when I applied the mud the mud will actually fill a hole. And it's easier to cover that hole and blend it in with the rest of the wall. Next we're going to take a glop of mud or joint compound.

How long does mudding take to dry?

24 hoursAt the far end, drywall mud, also known as joint compound, needs to dry for 24 hours between each coat and before sanding, priming, and painting. The 24 hour drying time recommendation can be applied to nearly all factors.

Step 1 - Mix the drywall mud

All purpose drywall compound or Lightweight all purpose drywall compound can be used to coat corner bead. Mud used to coat corner bead is some of the thicker mud you will use. Only a small amount of water is added to thin it slightly.

Step 2 - Apply mud from top toward the center

Using an eight or ten inch drywall knife, spread drywall compound evenly on the drywall near the corner bead. The knife should run against the bead as a guide. Don’t allow the knife to pull away from the bead. The mud should be evenly dispersed across and under the knife.

Step 3 - Apply mud from bottom up

Spread drywall mud from the bottom of the bead pulling up and into the mud applied in the previous step. Subsequent applications of drywall mud should be pulled into mud already on the wall rather than pulling away from mud on the wall. Therefore, mud should be applied to the bead from the center toward the two ends.

Step 4 - Feather the edge of the mud toward the drywall

Using heavy pressure on one side of the knife, clean the outside edge of mud applied on the wall. Notice in the picture how one finger is placed to the left of the handle on the drywall knife. This aids in placing pressure where needed. You may want to click on the picture for a larger image.

Step 5 - Smooth mud from bead to drywall

Once drywall mud is applied evenly along the length of the corner bead and the edge has been feathered smooth with the surrounding drywall, run the knife along the entire length of the corner bead using even pressure. The right side of the knife should run along the corner bead as a guide while the left side should run along the drywall.

Step 6 - Allow to dry and apply second coat

Once the mud has dried, repeat the process above using a larger drywall knife. If you used an eight inch knife on the first coat, use a ten inch on the second coat. If you used a ten inch knife on the first coat, use a twelve inch knife on the second coat. At times a third very thin coat is needed to cover any residual imperfections.

Conclusion

After drywall corner bead has been installed, it can be coated after taping is finished. The first coat should be applied before you apply a second coat to the seams. The second coat of mud can be applied anytime after you first coat the seams and butts. All Purpose or Lightweight All Purpose joint compound is best.

Paper-faced corner bead makes taping outside corners a snap

Outside drywall corners have traditionally been protected with nail-on metal corners, but paper-faced corner bead is simpler and resists cracks and chips better. All you need to install it are taping knives and a spray bottle filled with water.

Overview: Corner Wall Beading

Traditional metal corner drywall bead is tedious and time-consuming to install, and if you don’t cover metal corner with tape, it’s likely to develop cracks along the edges. Luckily there’s an alternative that’s simpler to install that metal corner and won’t crack.

Step 1: Cut the drywall paper beading with tin snips

If you need to cut pieces to length, simply hold the wall beading in place, mark the cut, and cut the bead with tin snips. Where pieces run to the floor, cut them about 1/2 in. short. The baseboard will cover the gap.

Step 2: Mud the corner

Spread a thick layer of all-purpose joint compound on both sides of the corner and smooth it off with a putty knife. Avoid lightweight joint compound because it doesn’t adhere as well to the corner bead. Strive for an even, consistent layer of joint compound about 1/8 in. thick. Don’t leave any thin or dry spots.

Step 3: Mist the wall beading

Wetting the paper covering on the corner bead helps create a better bond and better adhesion and cuts down on wrinkles. Do this by spritzing the corner wall beading before you stick it to the wall. You don’t have to soak the corner bead; just dampen it a bit.

Step 4: Position the drywall paper bead

Press the dampened corner bead into the joint compound with your fingers. Run your fingers up and down while pressing evenly on both sides to embed and center the corner bead.

Step 5: Embed the tape

After positioning the wall beading, wipe and smooth off excess joint compound with a 5- or 6-in. putty knife. Press the edge of the tape with the knife blade to ensure a tight bond with the drywall.

BENEFITS OF SPRAY-AND-STAPLE METHOD

The tried-and-true technique for outfitting your corners with toughened vinyl, just because this method is conventional doesn’t mean it’s not highly effective. Spray-and-staple standard corner beads are a mainstay of drywall finishing for a good reason — they’re highly effective, stand the test of time and don’t have much of a learning curve.

INSTALLING STANDARD VINYL CORNER BEAD WITH SPRAY AND STAPLES

The spray-and-staple technique uses a spray adhesive — such as the high-tack, pressure-sensitive Trim-Tex 847 discussed above — to attach the bead before stapling it in place. Spray continuously from a distance of 6 to 10 inches, being sure to keep the spray moving to avoid buildup on the drywall or bead surface.

BENEFITS OF MUD SET

Mud Set Beads are drywall corner beads made from high-impact, rigid vinyl, featuring Trim-Tex's patented Mud Lock Technology.

INSTALLING MUD SET BEADS

To install these Mud Set Beads, run them through a 4-in-1 Mud Hopper, or use a knife or compound applicator tube to apply the mud onto the corner directly. The hopper installs Mud Set 90 Degree Bead, Mud Set Bullnose and Splayed Beads with ease to help minimize jobsite delays.

INSTALLING FAST EDGE CORNER BEADS

Since it also features Mud Lock Technology, the process for installing Fast Edge is quite similar to that of Mud Set Beads — no staples or sprays required.

Choosing Joint Compound

For a durable finish use setting-type joint compound, also called mud, for the first coat over the metal. Ready-mixed compound can be used for the second and finish coats but it's too soft and prone to shrinking when used in a thick application like that required to cover metal corner bead.

Cut the Bead to Length

Measure the length with a tape measure and cut a piece of bead for each outside corner. Use a pair of tin snips or scissors to cut in from each side of the metal and then bend it in the middle to break it apart.

Attach the Bead with Drywall Screws

Hold the bead against the corner while pressing hard on the peak with your palm to flatten it tightly to both walls. Start near the top and drive a 1 5|8 or 2 inch drywall screw through one of the small holes in the metal and into the wall frame.

Cover the Corner with Joint Compound

Use a 6 inch drywall joint knife to apply a thick coat of setting-type joint compound in crossing strokes along both walls, from one end to the other. Use a very thick coat that covers all the metal and spreads well onto the the drywall.

Smooth Out the Mud

Float the other wall in the same way. Clean the mud off the joint knife frequently as you work to avoid buildup. When you finish, go back to the start and run the clean blade along the whole length of each wall again, in one smooth stroke to leave a level surface.

Apply a Second Coat of Mud

When the mud is completely hard, use a larger joint knife to apply a second coat using ready-mixed compound. First scrape over the hardened mud with the blade to knock off any rough spots and then apply a thick coat of compound onto both wall surfaces. Use crossing strokes to cover the corner completely and overlap the wall edges of the first coat.