Place the nails 6-1/8” above the butt edge, 1” and 13” from each end ½” from each cutout. Do not insert nails into or above the sealing strip. For shingles in windy areas use 6 nails per shingle. Make sure none of the nails are within 2" of joint of shingle. The nails must penetrate well into the wooden roof deck.
How far do you nail cedar shingles?
Nails should be long enough to penetrate underlying materials in the cedar shingles at least 3/4 inches, or all the way through. Use two fasteners to apply each Certi-label shingle or shake. Apply both nails 3/4 inches from the edge of each shake or shingle, and about 1 1/2 inches above the exposure line.
How do you nail shingles to a roof?
The size and diameter of the nails is critical to your success. Go with corrosion resistant nails if you seek quality results. Generally, as you start shingling the roof, lay a row of shingles beginning from the lower left corner of the roof and nail down the shingles as you go along.
How do you fix a hole in a shingle roof?
The nails must penetrate well into the wooden roof deck. If the nail fails to penetrate the deck properly then remove the nail and repair the hole in the shingle with bituminous mastic and use another nail. Try not to break the shingle surface with the nail head and repair any incorrectly placed nails immediately.
How do you staple wood shingles with Staples?
Staples used on wood shingles or shakes should have crowns between 7/16 and 3/4 inch wide and penetrate the sheathing by 3/4 inch. Drive wood shingle nails flush. Do not drive nail heads or staple crowns below the surface of the shingle. Underdriving or overdriving weakens the shingle attachment.
How many nails are required for Owens Corning shingles?
What are roofing nails made of?
How far away should nails be from shingle?
What is the purpose of shingles and underlayment?
What happens if you adjust your nail gun?
Why are Duration shingles laminated?
What is the best way to install shingles?
See 4 more
About this website
What type of nails do you use for wood shingles?
We recommend stainless steel fasteners, hot-dip galvanized, or aluminum. With time, inappropriate fasteners can leave rust marks on the shingles, especially on natural cedar shingles.
How do you attach wood shingles?
3:287:07And the nail shouldn't be driven too deep. So you want to keep the nail up high like that so itMoreAnd the nail shouldn't be driven too deep. So you want to keep the nail up high like that so it grabs as much of the meat of the wood. Lessening. The chance for it to lift off.
Can you use a nail gun on cedar shingles?
Tools & Fasteners It's possible to install cedar shingles with a hammer, and that provides the most control, but with 900 nails per square, the job will go a lot faster if you use a pneumatic nail gun. The other big advantage to using a nail gun is that you have one hand free to hold the shingle-strip.
How do you secure cedar shingles?
0:122:39One of my favorite woods to work with is cedar. Today we're going to talk about installing cedarMoreOne of my favorite woods to work with is cedar. Today we're going to talk about installing cedar shingles. So the first thing that you want to consider when you're doing cedar siding is what kind of
Is it better to nail or staple shingles?
Both nails and staples have sufficient strength to resist small uplift load on the shingles, as long as the tabs remain sealed. If staples are properly installed, they offer nearly the same wind resistance as nails. The problem with staples is the orientation of the staple crown.
How many nails do I need for wood shingles?
two fastenersUse two fasteners to apply each Certi-label shingle or shake. Apply both nails 3/4 inches from the edge of each shake or shingle, and about 1 1/2 inches above the exposure line.
What do you nail shingles down with?
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, long enough to penetrate through plywood or 3/4" into boards. Use 4 nails per shingle placed 6-1/8" above the butt edge, 1" and 13" in from each end and 1/2" above each cutout.
Should shingles be hand nailed?
What Does the Shingle Manufacturer Say? Roofing manufacturers have determined that hand-nailing shingles and using a nail gun are both valid methods of installing shingles, so it is not a reflection on your roofer's work quality level if they choose one over the other.
Do you have to use roofing nails for shingles?
You cannot use screws for roofing shingles, only roofing nails are approved fasteners. Screws leave small gaps in the material they are driven into, and this may be enough to allow for a leak.
Do you need special nails for cedar?
Hot-dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and can be used to nail Western Red Cedar. Other types of nails are not recommended. They can rust and disintegrate and react adversely with the natural preservative oils present in cedar resulting in stains and streaks.
How many nails do I need for cedar shingles?
twoFasteners, two (2) per shake or shingle, shall be applied approximately 3/4" from the edge and approximately 1 1/2" above the exposure line. Fasteners shall be long enough to penetrate into the sheathing at least 3/4" or all the way through.
How do you nail the last row of shingles?
How to Finish the Top Edge of a Shed RoofFor the final row, cut shingles into strips.Ensure strips are wide enough to cover nails.Install your strips.Apply sealant over exposed nails on the last strip.Use more sealant along the top edges of all shingle strips.
Are shingles glued or nailed?
Shingles are designed to be nailed on a specific location and the nail must be driven to a certain depth.
Do shingles need to be glued down?
In areas with high winds, or when the shingles are applied to steep slopes (>21:12), or when shingles are applied in cold winter weather, wind safety should be ensured by sealing down each tab of a three-tab shingle with asphalt plastic cement.
Are shingles supposed to be glued down?
Shingles are still held to roof decking with nails, or in some jurisdictions where it is allowed, staples. However, there is also a strip of heat-activated adhesive that runs along the top of each shingle.
Can you staple wood shingles?
The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. For locations outside of the salt water zone - stainless steel staples Type 304 or Type 316 must be used.
roofing nail size - Fine Homebuilding
Save up to. 76% off. the cover price. In-depth articles, up-close. photography, and detailed. illustrations in every issue. Subscribe Now!
What size roofing nails do i need - Roofgenius.com
Roofing nails, roofing nail sizes, sheathing,3d box, 4d box, 5d box, 6d box, What size roofing nails, Composition Shingles, Wood Shakes, Wood Shingles.
How many nails are required for Owens Corning shingles?
A four-nail fastening pattern per shingle is required to take advantage of the maximum wind warranty available on Owens Corning® Duration® shingles. Six nails are required for structures with slopes exceeding 60 degrees or 21 inches per foot. In some areas of the country, building codes may require six nails as well.
What are roofing nails made of?
Nails can be made of: Aluminum. Copper. Sta inless steel, or. Galvanized steel (zin c-coated) Some roofing nail materials are more suitable for certain geographies than others. For instance, if you live in a coastal area where your home is exposed to salt, stainless steel roofing nails may be a good choice.
How far away should nails be from shingle?
Roofing nails are typically placed no closer than 1 inch from the edge of the shingle according to the manufacturer’s specifications.
What is the purpose of shingles and underlayment?
Roofing shingles and underlayment work together to provide your home with protection from the elements, including rain, snow, and wind. But these roofing products can only do their jobs when properly installed.
What happens if you adjust your nail gun?
Nail guns that are improperly adjusted can result in either under penetration or over-penetration of the roofing nails, which then affects the shingle’s performance. It can also cause:
Why are Duration shingles laminated?
Duration® Series shingles are called laminated shingles because there is an underlay piece that is adhered to (or laminated to) an overlay piece. This construction gives the shingles a natural depth and dimension. The place where the two shingle layers come together is called the common bond.
What is the best way to install shingles?
The best practice for installing shingles for maximum protection is through the common bond area. When nailing through the common bond and the SureNail® fabric on Duration® Series shingles, it creates a triple layer of reinforcement (called Triple Layer Protection®), which helps provide increased nail pull-through protection that is important in high winds.
Where and How to nail shingles to a roof?
Properly layered shingles are the key to avoiding water damage and leaking. Quality roofing nails need to be used to fasten the shingles and to install the roofing underlayment for waterproofing. Shingles may be one of the simplest roofing materials but require specialized and exact rules on how to fasten them.
Why do you need to use nails on shingles?
Properly layered shingles are the key to avoiding water damage and leaking. Quality roofing nails need to be used to fasten the shingles and to install the roofing underlayment for waterproofing. Shingles may be one of the simplest roofing materials but require specialized and exact rules on how to fasten them.
Can you break a shingle with a nail?
If the nail fails to penetrate the deck properly then remove the nail and repair the hole in the shingle with bituminous mastic and use another nail. Try not to break the shingle surface with the nail head and repair any incorrectly placed nails immediately.
How many nails are required for Owens Corning shingles?
A four-nail fastening pattern per shingle is required to take advantage of the maximum wind warranty available on Owens Corning® Duration® shingles. Six nails are required for structures with slopes exceeding 60 degrees or 21 inches per foot. In some areas of the country, building codes may require six nails as well.
What are roofing nails made of?
Nails can be made of: Aluminum. Copper. Sta inless steel, or. Galvanized steel (zin c-coated) Some roofing nail materials are more suitable for certain geographies than others. For instance, if you live in a coastal area where your home is exposed to salt, stainless steel roofing nails may be a good choice.
How far away should nails be from shingle?
Roofing nails are typically placed no closer than 1 inch from the edge of the shingle according to the manufacturer’s specifications.
What is the purpose of shingles and underlayment?
Roofing shingles and underlayment work together to provide your home with protection from the elements, including rain, snow, and wind. But these roofing products can only do their jobs when properly installed.
What happens if you adjust your nail gun?
Nail guns that are improperly adjusted can result in either under penetration or over-penetration of the roofing nails, which then affects the shingle’s performance. It can also cause:
Why are Duration shingles laminated?
Duration® Series shingles are called laminated shingles because there is an underlay piece that is adhered to (or laminated to) an overlay piece. This construction gives the shingles a natural depth and dimension. The place where the two shingle layers come together is called the common bond.
What is the best way to install shingles?
The best practice for installing shingles for maximum protection is through the common bond area. When nailing through the common bond and the SureNail® fabric on Duration® Series shingles, it creates a triple layer of reinforcement (called Triple Layer Protection®), which helps provide increased nail pull-through protection that is important in high winds.
