how do you open a dryer door

• Gather Your Tools. It helps to have all your tools ahead of time. Fortunately, this process is very simple and shouldn’t require more than the basic screwdrivers.
• Open and Examine Your Dryer Door. Screwdrivers at the ready, open your dryer door. Take a close look at how the hinges are connected and how the door latch connects.
• Remove the Hinges and Door. Confident in the design, take your Phillips head screwdriver and remove the screws attaching the hinges to the dryer.
• Remove the Hinges. Spread your towel out on the floor or your work surface and place the dryer door ontop of it, hinges facing up.
Flip Your Front Panel Around. Here’s the part you may not have determined: How does the handle flip? ...
Attach the Hinges to the Opposite Side. Now reinstall the hinges. Align them with the new screw holes opposite the door handle. ...
Switch the Door Latch and Matching Cover. The final step is to switch the door latch hardware. ...
Attach the Door to the Opposite Side. Look to the hinge mounts you’re about to use – opposite of the previous hinge location on the dryer.
Test Your Success. Now it’s time to step back and admire your work. Open and close the door. See if it is well aligned and if it sticks closed.

Full Answer

How do you open a whirlpool dryer door?

The inner and outer panels that comprise the dryer door should come apart. Flip the outer panel, the front panel containing the handle, so that the handle points in the other direction. You may notice that the hinge screw-holes went with it in the flip, and are matched on the inner panel.

Can you switch the direction of your dryer door?

– How to Switch the Direction of Your Dryer Door The direction that your laundry machine doors open seems trivial – right up until it isn’t. Nothing is more frustrating than a dryer door that opens the wrong direction, against the washer, or into the path. There are many reasons why you might have a preference for which way your dryer opens.

How do you remove the handle from a dryer door?

Look around the outer edge of your dryer door and find the perimeter screws. Remove these screws and set them aside nearby. The inner and outer panels that comprise the dryer door should come apart. Flip the outer panel, the front panel containing the handle, so that the handle points in the other direction.

What should I do if my dryer door is bent?

If the hinges are bent, you can use a screwdriver to straighten the hinges into place. Be careful not to break the hinges. You’ll need to replace damaged hinges before the dryer will work again. If the door is physically bent or damaged, you can bend it back manually as best as possible.

What to do if dryer swings shut?

If it does swing itself shut (or open), then test the level and balance the length of the screw-out dryer feet. If all tests well, give yourself a pat on the back. Not only have you just tackled a great work of appliance repair – you’ve also fixed a critical flow issue in your laundry room.

How many holes are there in a dryer?

Look to the hinge mounts you’re about to use – opposite of the previous hinge location on the dryer. You will likely find four to eight holes covered in small plastic covers. Remove each cover with your fingernail or the slot screwdriver and put them into the opposite holes.

Where is the moisture sensor on a dryer?

Unplug the moisture sensor wire, located at the bottom right of the side of the dryer drum.

Where is the door sensor wire located?

Unplug the door sensor wire, located on the right side of the inside of the top of the upper panel. To disconnect, lift the tab on the connector and pull the two connectors apart.

Where is the lint trap on a dryer?

The lint trap is either located on the top of the dryer cabinet, or in the dryer door jamb. It is important to clean the lint screen after each load to prevent a fire.

How to keep dryer door closed?

This suggestion popped up more times than you would think. Use two bungee cords wrapped around the dryer to keep the door closed.

How to keep dryer door from popping open?

Attach hook-and-loops with adhesive to the top and bottom corners of the dryer door. This will work like the magnets. Instead of using magnetic attraction, these hooks will fasten when the door is closed and keep it from popping open.

How to remove catch and strike on dryer?

The metal bracket behind the catch is what’s attaching it to the unit. Use needle-nose pliers to remove the catch.

Why does my dryer turn off when it overheats?

If there is a mechanical issue with the dryer, it could be overheating and setting off the thermal switch. This switch automatically turns the dryer off when it begins to overheat.

Why won't my dryer close?

If either the catch or striking mechanisms are broken, the dryer will not close. Don’t worry; this is a relatively simple fix. You can check out our step-by-step guide below for a handy how-to.

How to straighten a door frame?

You can tighten the hinges on the frame to straighten the door. If the hinge s are bent, you can use a screwdriver to straighten the hinges into place.

What to do if latch isn't catching?

If the latch isn’t catching, you may need to replace the strike or catch. Closely examining what happens with these two mechanisms will determine if you need one or both components.