How do I program the water days on my sprinkler system?
Twist the dial so that it is in the “Water Days” position. This will switch the display on the controller to days of the week. Use the left and right arrows to cycle through the days. To program properly, the days should be shown as follows: A water droplet icon indicates a day that you want your sprinklers to run.
How does the Hunter smart irrigation controller work?
The Hunter system offers a unique advantage, thanks to its innovative Smart Irrigation controller features. You can easily control and automate your sprinklers through the control system for automatic turn-on and shut-off, as well as scheduled watering times. This is based on the Hunter Run Time Calculator. What is the Hunter Run Time Calculator?
How do I adjust the current time on my Hunter sprinkler system?
To adjust the current time on your Hunter sprinkler system controller, turn the dial to “Current Time/Day. ” This will cause the displayed numbers to start flashing. Then, use the plus and minus buttons on the device to change the numbers accordingly.
What do I need to set up my lawn program?
To set up each program, you would need START TIMES, RUNTIMES, and WATER DAYS for each of them. You have a 4 Station Pro-C controller. Your lawn stations are valves #1 and #2.
How do I program a hunter irrigation system?
Watch our quick video above, or continue reading to learn how to program your Hunter X-Core Sprinkler System.Step 1: Set The Current Time. ... Step 2: Set the Start Times. ... Step 3: Set the Run Time. ... Step 4: Set the Watering Days. ... Step 5: Test Coverage. ... Step 6: Finished!
How do you program a hunter node for sprinklers?
10:1811:24NODE: Programming the NODE irrigation controller - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply hold down the right arrow to enter the manual mode. Once there you can use the right arrow toMoreSimply hold down the right arrow to enter the manual mode. Once there you can use the right arrow to advance through the various stations that you want to turn on. When landing on the desired.
How do I set the start time on my hunter sprinkler system?
0:163:30HUNTER PRO C Controller (How to set program start times) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what we'll do is go ahead and turn your dial. Twice down to set program start times now up hereMoreSo what we'll do is go ahead and turn your dial. Twice down to set program start times now up here you'll notice it says start time one and then off is flashing.
How do I reset my hunter node?
0:050:40How To Reset A Hunter Node - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp press a key press any key a quick way to hard reset the controller is to hold down the negative.MoreUp press a key press any key a quick way to hard reset the controller is to hold down the negative. The right arrow and the program keys at the same.
How do I set the time on a Hunter node?
To program the Node battery operated irrigation controller you must first set the date and time. To set the time and date on the node press the center button, simply scroll through the choices using the left and right arrow buttons and adjust the displayed item using the plus and minus buttons.
Why does my hunter sprinkler system run twice?
A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time.
How do you program a hunter x2 controller?
0:3911:35X2 Irrigation Controller, Programming at the Facepack - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the right arrow to advance to the month and change it using plus or minus. Buttons. You pressMorePress the right arrow to advance to the month and change it using plus or minus. Buttons. You press the right arrow.
How do I change programs in Hunter Pro C?
Length:Start with the dial in the RUN position.Press and hold the button. Turn the dial to the WATER DAYS position.Release the button.Use the and button to change program modes.
How do you set a hunter node sprinkler timer?
To create a program on your Node battery operated sprinkler controller press the center button to access the start time programming option. Adjust your run times using the plus and minus buttons to set the minutes for each station. Use the right arrow to advance station number.
How do you program a battery operated sprinkler timer?
0:005:40Programming Orbit Battery Operated Underground Timer (57860)YouTubeStart of suggested clipEnd of suggested clipSo the start time is when we want the program to start obviously. And that each start time is goingMoreSo the start time is when we want the program to start obviously. And that each start time is going to run through every station for the allotted amount of time.
Why don't my sprinklers turn off?
If your irrigation system does not turn off, you need to isolate the problem. This starts by checking the main water line and the controller. If those are working, then you need to locate the valves and check to see whether they are dirty, the diaphragm is torn, or the solenoid is broken.
How to change the time on Hunter sprinkler system?
To adjust the current time on your Hunter sprinkler system controller, turn the dial to “Current Time/Day. ” This will cause the displayed numbers to start flashing.
Who makes Hunter sprinkler controllers?
Hunter Industries manufactures a number of lines of residential and commercial sprinkler system controllers. However, each operate similarly and are relatively easy to understand. We’ll walk you through all the steps to successfully program your Hunter sprinkler system, so that you can enjoy its full benefits.
Why won't my sprinklers open?
This could be caused by a number of reasons. If your sprinkler system’s controller displays the flashing sprinkler icon but your sprinklers are not running, you either have a wiring problem at the valves or your water supply has been shut off. If you have a master valve on your system, then the problem may be due to a master valve that won’t open. Inspect the wire connections at the master valves for any corroded or loose wires, or a faulty solenoid. If your system does not have a master valve, check that your valves have a water supply.
Why is my Hunter sprinkler system not working?
When the display on your Hunter sprinkler system controller shows “Err” this indicates an issue with the installation or an interference with the SmartPort wiring. It may also be the direct result of a faulty device plugged into the SmartPort. Check the wiring to be sure that it is correct and is not bundled. Bundling wires together can cause interference.
What does the water droplet icon mean?
A water droplet icon indicates a day that you want your sprinklers to run. A water droplet icon with a circle around it and a dash through it indicates a day that you do not want your sprinklers to run. These days will depend on the city you live in, as long as the time of the year.
How to determine the time to run sprinklers?
Make sure to factor in your local watering schedule to determine the appropriate time and day to run your sprinklers. With the dial turned to “Start Times,” use the left and right arrow buttons to switch between the first (morning) and second (evening) start times for the sprinkler.
Is Hunter sprinkler system easy to operate?
While the controller on your Hunter sprinkler system may look intimidating, it is rather easy to operate. With a greater understanding of all of the different settings and how to establish them, you can keep your landscaping healthy and maybe even save some money on your water bill!
What is a program in a watering station?
A program is a group of stations that share the same schedule: same days to water and same number of times per watering day. You only need one program (Program A) if you want all your zones to water on the same days and in a sequential order.
How to program a controller?
It only takes three ingredients to complete a program: a start time, run times, and days to water. A program is a group of stations that share the same schedule: same days to water and same number of times per watering day. You only need one program (Program A) if you want all your zones to water on the same days and in a sequential order. If some of your plants or lawn areas have different watering needs, they will need to be put in a separate program (Program B and/or C).
How to set a water day on a tu?
(If you see the “MO” flashing, press the right arrow 9 times until you see the symbol above “MO” flashing) Press the “+” to set Monday as a water day. Press the “-“ button when the symbol is flashing above TU, TU will show as a no-water day (drop with a circle). Press the “+” to set Wednesday as a water day, press the “-“ button to set Thursday as a no-water day, press the “+” to set Friday as a water day, press the “-“ button to set Saturday as a no-water day, press the “-“ button to set Sunday as a no-water day. The symbol will go back to flash above Monday. Program A is now set.
What time do you water lawn stations?
You want the lawn stations to water Monday, Wednesday, and Friday at 4:00 am and again at 6:00 am for 6 minutes per station. Finally, you want the shrub stations to water on Saturdays at 6:00 am for 10 minutes per station.
Why is there no watering in a program?
Because there are no start times, there will be no watering with that program. Example: Program A has four stations (1-4) assigned to it and the program has one start time at 5:30 AM. At 5:30 AM, station 1 will water, followed by station 2, then station 3, and so on until all four stations have watered.
How many start times are needed for watering stations?
All stations operate in numerical order. Only one program start time is required to activate a watering program. If a program has all four start times turned off, then that program is off (all other program details are retained). Because there are no start times, there will be no watering with that program.
How many times can you start a water station?
Each program can start up to 4 times on the set days to water. One start time will activate all stations sequentially in that program. If you want the stations to operate one time in sequential order and then not repeat, set start times 2, 3, and 4 to OFF. Multiple start times in a program can be used for separate morning, afternoon, ...
