Here’s our quick guide to installing a door kick plate:
- Hold the kick plate in the position of where you are going to install it. This will be at the bottom of the door. ...
- Fasten the plate in place with some tape or anything else that will do the job.
- Mark on the door where you are going to be screwing. ...
- Remove the plate from the door.
How to properly kick in a door?
Pull the door towards you slowly to begin closing the door.
- If you are inside of the room you are closing the door to, then this will require a pushing motion instead of a pulling motion.
- Some doors are weighted to partially or fully close by themselves. ...
- Old, wooden doors that are lightweight may require you to quickly pull the door shut in one sweeping motion to keep the hinges from creaking. ...
How to install kick plates on steel doors?
How to Install a Door Kick Plate Screen
- Place the kick plate against the bottom of the door, centering it approximately two inches up from the bottom edge.
- Mark the location of the four corner screw holes with a pencil. Set the kick plate aside.
- Drill a 3/4-inch deep hole through each marked location on the door. ...
How to clean brass kick plate on door?
How to clean a brass kick plate?
- Wipe off as much dry dirt from the kick plate as possible using a old rag. ...
- Mix several tablespoons of salt into a 1-pint spray bottle filled with white vinegar. ...
- Spray the salty vinegar over the brass and allow it to sit for 10 minutes or so.
How to attach kick plate?
Steps
- Prepare the kickboards for cutting. Measure the lengths your kickboards need to cover under your cabinets and mark them up with a combination square.
- Cut the kickboard to size. Put some cardboard under the kickboard and clamp it to the sawhorses. ...
- Mark out the drilling points for the kickboard. ...
- Install the kickboard. ...
What is a door kick plate?
How to make a hole in a door?
How to drill a hole in a steel door?
Can you install a kick plate on a door?
Can you put kick plates on steel doors?
Can you install magnetic kick plates on steel doors?
See 3 more
About this website
Can you glue a kick plate to a door?
You can also apply some liquid nails to the back of the kick plate for a more permanent fixing. This option comes with the factory-applied adhesive tape on the reverse of the plate; the self- adhesive tape firmly holds the kick plate in place on the door while the fixing screws are installed.
How do you attach a kick plate to a door?
0:211:33How Install a Door Kick Plate and Measure for Correct ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll first apply loops of the painters tape to the back of your custom kick plate. This will allowMoreYou'll first apply loops of the painters tape to the back of your custom kick plate. This will allow you to position the kick plate perfectly. For the final installation.
What side of a door does a kick plate go on?
push sideA kick plate is installed at the bottom of the door on the push side and ranges in height from 8” to 16”. This style of protection plate is the most common form of commercial door protection.
Where should a door kick plate be placed?
0:493:42How To Install A Door Kick Plate - YouTubeYouTubeStart of suggested clipEnd of suggested clipAn inch down from the bottom of the embossed panel. And two inches in from either side that way whenMoreAn inch down from the bottom of the embossed panel. And two inches in from either side that way when I install it's going to look very decorative. And certainly add to the door.
How much does it cost to install a kick plate?
Adding a kick plate to a storm door will cost about $20 to $50. Costs vary greatly by region (and even by zip code).
How high should a kick plate be on a door?
The kick plate should be installed 1" above the bottom edge of the door and approximately 2" less in width than the door.
Do kick plates go on both sides?
You can install kick plates on both sides of the door if you wish, and enjoy the custom look and protection whether inside or outside.
What is the difference between a kick plate and a mop plate?
The ONLY difference between Mop Plates, Kick Plates, and Armor Plates is the HEIGHT. Don't forget we have a standard quantity discount of 10% for quantities of 20 or more. Please contact us for quantities above 50.
What is the purpose of a kick plate on a door?
A kick plate is a metal, wood, or plastic guard used to protect the bottom of the door when the door is kicked open. Kick plates are a simple DIY project and are offered in several finishes. Kick plates are installed with screws or two-sided tape. There is also a magnetic option.
Are kick plates still in style?
Kick plates are common on the doors of commercial businesses but they are increasingly being used on residential doors as well.
What is the standard toe kick height and depth?
Toe Kick. Below the base cabinet, there is a recessed area known as the toe kick. It typically measures 3 inches in height and the depth is approximately 3.5 – 4 inches.
How does a kick plate work?
The Kick Plate is a flush-mounted, hydraulic plate set flush to the road. Its surface is designed to induce loss of rear wheel traction, putting the car into a skid or spin. You will be taught the correct technique to 'catch' the slide and bring the car under control, (but maybe not the first time).
What is the bottom plate of a door called?
The piece at the bottom of a door is called a sill. Door sills help prevent air and water from getting in your home. A door stile is a vertical section on the outside edge of a door panel. They help to frame your door panel.
Measuring, Ordering and Installing a Kickplate | TheKickPlateStore
TheKickPlateStore Instructions on How To Measure For A Kick Plate, Mop Plate or Armor Plate | The Kick Plate Store
What is a door kick plate?
Whether you're looking to provide robust protection from damage or make an architectural statement, there's a door kick plate manufactured to fit your needs. Although the most common kick plates are the flashy brass variety adorning wooden entry doors, the extra protection will help a steel door look better and last longer as well.
How to make a hole in a door?
Hold a center punch firmly against the door at one of the hole marks. Hit the punch with a hammer to create a depression at the hole location. Repeat the process for each of the holes.
How to drill a hole in a steel door?
Place the tip of the drill bit in the indentation left by the center punch. Squeeze the drill trigger lightly at first so the bit doesn't skate on the steel as you start the hole, then slowly increase drilling speed. Stop drilling once you have completely penetrated the steel skin of the door.
Can you install a kick plate on a door?
Installing a kick plate is easier with the door removed and placed flat on the floor, but mark the position of the plate on the closed door first so you know it will clear the jambs, threshold and any weatherstripping.
Can you put kick plates on steel doors?
They are available in many different materials and sizes. With the right tools and technique, it's no harder to install kick plates on steel doors than on those made of wood.
Can you install magnetic kick plates on steel doors?
If theft won't be a problem, there are magnetic kick plates that install on a steel door without drilling holes.
How to secure a kick plate to a door?
Hold the kick plate back up against the door and start securing it. Put in top and bottom screws first and then make your way outwards with the screws. This should ensure it lays flat against the door without any warping.
What is a Door Kick Plate?
Door kick plates are a sheet of material attached to the bottom of your door to protect it from damage.
How tall is a kick plate?
They’re roughly 25-40cm tall and incredibly easy to install. If your door doesn’t open in the direction that you would expect it to, or it is a swinging door, you may benefit from installing kick plates on both sides of the door. Hold the kick plate in the position of where you are going to install it.
How far from the edge of a door should a kick plate be?
Hold the kick plate in the position of where you are going to install it. This will be at the bottom of the door. Allow 2.5cm of clearance from the edge of the door.
Where are door kick plates used?
Door kick plates are more commonly used in public and commercial buildings than on homes but that’s not to say they aren’t something that should be considered.
How to make depressions on door?
Using a hammer and a centre punch, or anything else that will do the job (a screwdriver might be effective for example), create depressions at each of your markings on your door. Using a sharp drill bit, take the tip of the drill to your markings.
Where are kick plates installed?
Kick plates are installed at the bottom of the door. You need to decide which doors are going to benefit the most from this. This is normally why they’re found on external doors of warehouses, shops, public buildings etc. They’re roughly 25-40cm tall and incredibly easy to install. If your door doesn’t open in the direction ...
How to size a door kick plate?
How to Size a Door Kickplate. When you open an exterior door with your hands full, you probably push the door inward with your foot. Kick plates are flat metal panels you attach to the bottom section of exterior doors to protect the finish from dirt and damage from the toe of your shoe.
How high should a kick plate be on a door?
If your door has fewer than 8 1/2 inches between the bottom and the decoration, select a 6-inch kick plate. If it has fewer than 6 1/2 inches, custom order a kick plate to fit in the space. If your door has no decorative paneling or insets, the height of the kick plate is up to you.
What happens if you leave a kick plate on the side of a door?
If the kick plate covers the entire width, the door won't close properly, and leaving these inches bare on the sides gives the door space to fit behind the weatherstripping. They also allow the color of the door to peak through at the edges, which is the traditional look for doors with kick plates.
What is a kick plate?
Kick plates are flat metal panels you attach to the bottom section of exterior doors to protect the finish from dirt and damage from the toe of your shoe. Although you can cut most kick plates down to fit your door, it's quicker and easier to measure the door before you order the plate so you get the right size.
How to measure for a kick plate?
Measure the height from the bottom of the door to the bottom of the first decorative panel or inset on the door. Subtract 1 inch from the total to allow 1/2 inch of clearance on the top and bottom of the kick plate. Standard kick plates are either 6 or 8 inches tall. If your door has fewer than 8 1/2 inches between the bottom and the decoration, select a 6-inch kick plate. If it has fewer than 6 1/2 inches, custom order a kick plate to fit in the space.
How high are kick plates?
Standard height of kick plates available in the market are between 10 and 16 inches↗ high. Currently metal, vinyl, and plastic kick plates are available in the market. Most homeowners choose metal kick plates because they look nicer and are more durable than their cheaper counterparts.
What to do if your door warranty has expired?
If your warranty has expired then go ahead and add the kick plate, if it hasn’t then you may want to hold off on adding that kick plate. Some manufacturers are very particular about the details of the warranty and you may want to follow the terms in case you need to file a claim for another reason later.
Can you buy kick plates separately?
You can purchase kick plates preinstalled on your door or you can purchase them separately to install at a later time. If you decide to add kick plates later, make sure to check the warranty on the door.
Do I need a kick plate on my front door?
No. Kick plates are not necessary but they are a great feature to protect the surface of the door. It will not only protect the finish of your door from scuff marks and scratches but it gives the door an additional little design touch, just make sure to choose one that complements the design of your door. Kick plates are common on the doors of commercial businesses but they are increasingly being used on residential doors as well.
What is a door kick plate?
What’s A Door Kick Plate? Kick plates are an addition to the bottom of your door that help reduce the amount of damage and stress that your door takes over time. They’re installed on the push side of the door. The term kick plate comes from the fact that when people’s hands are occupied they often kick the bottom of the door to open it. ...
Why are door kick plates important?
Commonly used on business and other commercial buildings, door kick plates are a small detail that go a long way in protecting your door’s life. Businesses often use them because people come in and out with packages and can easily kick the door open without damaging it. Without a kick plate, that door will wear out ...
Why are kick plates needed?
Why Kick Plates Are Necessary. The obvious reason why door kick plates are installed is to cover the bottom of the door to guard against damage. You’re more likely to see kick plates on commercial buildings and business buildings such as restaurants. The higher volume of traffic that businesses see with people coming in ...
Why do people kick plates?
Kick plates on residential homes have become increasingly popular as people’s lifestyles are becoming more fast-paced and demanding more efficiency. If you have your hands full of groceries, books, luggage or even children, your instinct is usually just to kick the door open.
Can you replace a door without a kick plate?
However, if you notice that your door has suffered much damage after years without a kick plate, it might be time for a replacement. After noticing all the damage your door has been through, getting a new one is an investment worth while. Entry doors from Feldco offer the best in strength, beauty and energy efficiency.
Can you replace a fiberglass entry door with a steel one?
A surefire way to make your home stand out and look beautiful is to replace your old entry door with a steel or fiberglass one. Unlike wood doors, steel and fiberglass entry doors will never rot, warp or expand.
Do door kick plates really work?
You’ll probably notice that it happens more than you thought. Not only do door kick plates offer the added protection, they add to the beauty of your door. Having a nice solid brass or steel component can really make your front door pop and increase your home’s curb appeal.
Where should the kickplate be placed on a door?
It should be centered in the area at the bottom of your door. Once you are satisfied that the kickplate is positioned properly, attach the kickplate at each corner with a screw. This will stabilize the kickplate while you install the rest of the screws. Remove the protective film.
How high should a kickplate be?
The height and placement of your kickplate depends on personal preference. We offer a standard kickplate height of 6” or 8”. There are so many different styles of doors.
How wide is a standard door?
A standard exterior door is 36’ wide. We recommend leaving a border, or reveal, around your kickplate. Our standard kickplate is 34” wide and is the perfect fit for a standard door. But many newer homes are being built to accommodate wheelchairs and other mobility devices, so be sure to measure your door carefully.
Can you attach a kickplate to a saw horse?
Whenever possible, remove the door and place it across some saw horses, or on your workbench or even on the floor. You can attach your new kickplate to your door while it is still in place, but it’s easier on your back and knees if you can remove the door and place it at a more convenient height while working on it.
What is a door kick plate?
Whether you're looking to provide robust protection from damage or make an architectural statement, there's a door kick plate manufactured to fit your needs. Although the most common kick plates are the flashy brass variety adorning wooden entry doors, the extra protection will help a steel door look better and last longer as well.
How to make a hole in a door?
Hold a center punch firmly against the door at one of the hole marks. Hit the punch with a hammer to create a depression at the hole location. Repeat the process for each of the holes.
How to drill a hole in a steel door?
Place the tip of the drill bit in the indentation left by the center punch. Squeeze the drill trigger lightly at first so the bit doesn't skate on the steel as you start the hole, then slowly increase drilling speed. Stop drilling once you have completely penetrated the steel skin of the door.
Can you install a kick plate on a door?
Installing a kick plate is easier with the door removed and placed flat on the floor, but mark the position of the plate on the closed door first so you know it will clear the jambs, threshold and any weatherstripping.
Can you put kick plates on steel doors?
They are available in many different materials and sizes. With the right tools and technique, it's no harder to install kick plates on steel doors than on those made of wood.
Can you install magnetic kick plates on steel doors?
If theft won't be a problem, there are magnetic kick plates that install on a steel door without drilling holes.
