On smaller width stretch belts that are driven by the camshaft, like on some Ford and Mazda V6 water pump applications, you can use zip ties to install the belt. Simply zip tie the belt to the camshaft pulley and turn the engine until the belt is seated, then cut the tie. This method can also be used to keep some belts in place during installation. After the belt is installed, always confirm the belt is in the grooves and re-check that there are no alignment problems.
Full Answer
What tools do you use to install a belt?
If that's not an option or something, you can either look at stretch belt installation tools or do like I do & usually just end up using a standard screwdriver or small prybar to 'guide' the belt on to the pulley as I rotate the belt & pulley around. I use a wrecker bar, like a 48 inch long crowbar.
How do you install a water pump belt?
On smaller width stretch belts that are driven by the camshaft, like on some Ford and Mazda V6 water pump applications, you can use zip ties to install the belt. Simply zip tie the belt to the camshaft pulley and turn the engine until the belt is seated, then cut the tie. This method can also be used to keep some belts in place during installation.
What is a stretch belt on a lawn tractor?
Stretch belts are designed to stretch over one of the pulleys during installation, usually the crank or the largest pulley. Never use a screwdriver or other sharp object to install the belt because if the belt is cut or the surface or grooves of the pulleys are damaged, the belt will eventually fail.
What do you need to make an easy stretch belt?
All you need is a bit of soft, 1- inch woven elastic and a center release buckle and basic sewing supplies. How to an Easy Stretch Belt (in 5 minutes!)
How do you put a belt on a stretch belt tool?
0:201:44Lisle 59370 Stretch Belt Remover/Installer - Lisle CorporationYouTubeStart of suggested clipEnd of suggested clipPosition the tool so that the wedge-shaped removed side of the tool fits between the belt and pulleyMorePosition the tool so that the wedge-shaped removed side of the tool fits between the belt and pulley use a hand ratchet to turn the crankshaft in the direction that will rotate the pulley.
How do you install a stretch belt on an air conditioner?
1:102:34How to install AC stretch belt GM/Chevy 5.3 | 6.0 | 6.2 2009-2021YouTubeStart of suggested clipEnd of suggested clipYou're going to need a 24 millimeter you're going to put that belt around the back side of the crankMoreYou're going to need a 24 millimeter you're going to put that belt around the back side of the crank uh of your crankshaft. There. And then you're going to put it on to the right spot on the uh.
How do you get a stretch belt off?
0:091:41Remove and Install Stretch belt || Stretch Belt Hack - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you need is a ratchet with a 22 millimeter socket and a small pry bar. The special tool uses anMoreAll you need is a ratchet with a 22 millimeter socket and a small pry bar. The special tool uses an angled side to guide the belt on or off the pulley.
How do stretch belts work?
Stretchy belts grip the waist better, helping to keep your pants up. The belt flexes with movement, causing no restriction of motion. Flat elastic does not weigh a lot, keeping belts light and supple. With tension adjusted, elastic belts put less pressure on abdomen.
How do you use the Napa stretch belt tool?
0:372:24NAPA Service Tool Stretch Belt Mate™ Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou first position the belt over the accessory drive Cooling's such as the air conditioning powerMoreYou first position the belt over the accessory drive Cooling's such as the air conditioning power steering or alternator. Next place the installation tool over the crankshaft pulley.
How do you install a tight V belt?
0:331:44V-Belt Installation - Grainger Workbench Ep. 13 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen installing your V belt. Make sure to move your motor in by loosening the mounting bolts to helpMoreWhen installing your V belt. Make sure to move your motor in by loosening the mounting bolts to help ensure that you're not placing any unnecessary tension.
Can I reuse a stretch belt?
Some manufacturers like GM or Mazda do not recommend giving a second chance to the belt once it has been taken off. On the other hand, Chrysler and Ford say the belt can be reused if there are no problems found with the belt. Dismounting is pretty easy. Ford recommends using a simple tool, a nylon belt.Streeeetch That Belt - Auto Service Worldhttps://www.autoserviceworld.com › carsmagazine › stree...https://www.autoserviceworld.com › carsmagazine › stree...Search for: Can I reuse a stretch belt?
What belts are removed and installed using special tools to stretch the belt on and off the pulley?
Stretch belts are designed to stretch over one of the pulleys during installation, usually the crank or the largest pulley. Never use a screwdriver or other sharp object to install the belt because if the belt is cut or the surface or grooves of the pulleys are damaged, the belt will eventually fail.Everything You Need To Know About Stretch Beltshttps://www.underhoodservice.com › everything-need-kn...https://www.underhoodservice.com › everything-need-kn...Search for: What belts are removed and installed using special tools to stretch the belt on and off the pulley?
How do you put a stretch belt on a Ford Focus?
0:051:57Installing Stretch belts Ford Focus 2009-2011 Duratec HE 2.0LYouTubeStart of suggested clipEnd of suggested clipPlace the new serpentine stretch belt along the original root making sure the belt ribs alignMorePlace the new serpentine stretch belt along the original root making sure the belt ribs align correctly with the pulleys on the crankshaft. Water pump alternator.Installing Stretch belts Ford Focus 2009-2011 Duratec HE 2.0Lhttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you put a stretch belt on a Ford Focus?
How do you fit a belt?
An easy way to determine belt size is to simply “add 2″ to your off-the-rack trouser size. For example, if you wear a 36” waist trouser, then a 38 belt size will be a safe bet. Most will find this simple formula works best for pants worn at a traditional height–close to the natural waistline.
How do you change a AC compressor belt?
Step 3: Remove & Replace Belt.Loosen (but do not remove) the four bolts (1) holding the motor in place.Shift the motor towards the pump. The belt should be loose and easily removable.Move the motor back to the original position to create proper belt tension.Tighten the motor bolts.Replace the belt. (
How much does it cost to replace AC belt?
It's very cheap to replace a belt. Most cases the replacement cost is between $90 and $200. The cost of the belt will be between $25 and $75 while the labor costs will be between $75 and $120.
What is a stretch belt?
Stretch belts are designed to stretch over one of the pulleys during installation, usually the crank or the largest pulley. Never use a screwdriver or other sharp object to install the belt because if the belt is cut or the surface or grooves of the pulleys are damaged, the belt will eventually fail. Advertisement.
How to install a water pump belt on a Mazda V6?
On smaller width stretch belts that are driven by the camshaft, like on some Ford and Mazda V6 water pump applications, you can use zip ties to install the belt. Simply zip tie the belt to the camshaft pulley and turn the engine until the belt is seated, then cut the tie. This method can also be used to keep some belts in place during installation.
Why is my stretch belt so noisy?
Poor alignment is the number one cause of belt noise and premature wear of stretch belts. If the pulleys have poor alignment, the belt will be worn on the edges and might look frayed. Alignment problems can stem from issues with shaft endplay in an A/C compressor, water pump or power steering pump.
Why does my belt slip?
The primary cause of slipping is material being removed from the belt’s grooves, not belt stretching. Over time, small debris and the interaction with the pulleys will wear the shoulders and valleys of the grooves. When the grooves become too shallow, the pulleys bottom out.
How long do stretch belts last?
Stretch belts can last 100,000 miles or more , but this can vary dramatically depending on the vehicle’s environment and where it is mounted. This is why inspection is recommended — you cannot simply go by mileage recommendations.
What does "less belt" mean?
Less belt means less tension with fewer noise and vibration problems. More stretch belts are hitting the market and may become the belt of choice as accessory drive components are removed from the front of the engine.
When inspecting a stretch belt, always measure the depths of the groove with an inspection tool?
When inspecting a stretch belt, always measure the depths of the groove with an inspection tool because the differences between a worn belt and a good belt can’t be seen or felt. The new materials used to make a stretch belt might crack or separate like older belts before the grooves are worn. Belt gauges are available from manufacturers and distributors, so check their websites or ask your distributor.
How to an Easy Stretch Belt (in 5 minutes!)
I’ll admit, other than my hubby, neither the kids nor I hardly ever wear belts. But boy, when you need a belt, you probably need that belt ASAP and a plain black belt in child sizes can be hard to find!
Sewing instructions for a stretch belt
If making a belt for a particular pair of pants, I recommend having your child slip on the pants and measure at the point where the belt will sit . There can be a big difference between hip and waist measurements. (Although, if your elastic super stretchy, you might not need to worry too much.)
What size socket wrench does a KTC A1408 fit?
looks like it fits with a 1/2 in or 3/8 in socket wrench.
How many bolts does a harmonic balancer have?
The harmonic balancer is mounted to the crank with 4 bolts: the tool will catch on the 4 bolts or on a special seat in the front. There's not 1 single bolt. The belt stretcher too will mount the same way so you probably need a "special tool".
How to keep transmission in neutral?
turn the ignition on, put the car in neutral and touch off ignition witout removing the key, the transmision stays in neutral. not the best time to be working in the engine bay. this is a good point.
Does the AC belt have a tensioner?
PS: the whole issue is that the AC belt does not have a tensioner but is stretched over the two pulleys. In order to get to the main belt the AC belt needs to be removed and reinstalled. Click to expand... thanks, i'd be interested in hearing what your buddy has to say for sure. btw that's a nice neighbor to have...
How to measure belt length?
When replacing belts, you should ensure it is the best for the drive. On this premise, measuring its length becomes indispensable. The question is, how do you do it? Well, we have some answers for you as follows: 1 Flat surface: First off, put the spare belt on a table or any flat surface. 2 Tape measure: Get a tape measure and wrap it around the belt in question. Remember, this is a procedure for complete belts. Measuring the length of broken belts should be easy. Just stretch it alongside a tape measure and then get the value of its length from the tape measure readings.
What causes a lawn mower belts to stretch?
You have probably asked lots of questions about lawnmowers, but here is the catch. Did you get the right answers? For example, do lawnmower belts stretch, and what causes it? Based on many studies that further help explain the answer we gave at the beginning of the post, here is what you should know.
Why do mower belts elongate?
Continuous wear due to regular operation can cause them to elongate over time. When it stretches more than it should, it can result in the drive belts lose grip on the pulley system. When that happens, the efficiency of mowers takes a dip. You can adjust the belt tightness in some cases.
Do stretched belts affect pulleys?
Loose grip: First off, as the name suggests, stretched belts lose an effective grip on the pulley system. You can feel it by touching the drive. Their tension is low. Needless to say, stretched belts pose a bigger risk to the engine than any other part of the mower.
Step 1: How to Sneak in a V-Belt
V-Belts are commonly used to drive the accessories on the engine of a car. The common configuration shown has the crankshaft pulley driving the water pump (vital for cooling) and alternator (charges the battery) with V-belt A and the power steering pump and AC compressor driven by the crankshaft pulley and V-Belt B.
Step 2: You Can't Get There From Here
So you have a bad belt and look, you can't get to it because the pulley that you would adjust to slacken belt B (the light one) won't play nice. If you lack the leverage, heat, lubricant and time to move it. A (the dark belt) is too small to loop around all of the pulleys ahead of it, and the motor, mounts and such are behind belt A.
Step 3: The Sneak, Part 1
With the old belt A out of the way, place the new one (you got it right?) as shown on belt B. You will use the starter or some muscle to move one side of belt A around the pulley, but not the other one.
Step 4: The Sneak, in Progress
This shows the sneak in progress, with the belt partially rolled into place. You're almost there, carry on. Be sure not to get both sides of A between B and the pulley. It looks hard on the belts, but they stretch. I've done this a few times, never damaged the belts.
Step 5
Keep turning, now you've snuk!. You should be able to put the new belt A around the alternator and water pump, tension it and drive away. It wouldn't hurt to inspect the belts immediately and check the tension a little ways down the road. Hope this can be of help to somebody.
