Knowledge Builders

how do you put end caps on laminate countertops

by Loy Bosco Published 2 years ago Updated 1 year ago
image

  1. Fitting to Length Check for proper length. Allow desired overhang. End caps should be used on all exposed ends (end cap kits). ...
  2. Cutting Cover the Formica ® brand laminate surface in the area to be sawed with a strip of masking tape and draw a pencil line on the tape ...
  3. Buildup Place your countertop upside down on a flat surface. Choose strips of wood thick enough to allow the countertop surface to match the front build-up. ...
  4. Applying End Caps To apply end caps, set household iron at medium heat. Iron cap onto the end of the countertop with a back-and forth motion. ...
  5. Making Cutouts for Sinks or Rangetops Always follow manufacturer's directions for Installing appliances. ...
  6. Joining Miters If your kitchen requires an L- or U-shaped top, precut miters should be joined at this point in the installation. ...
  7. Scribing The countertop can be scribed to match the wall surface. The top is provided with a scribe edge on the backsplash for this purpose. ...
  8. Installing Sinks You may find it more convenient to install the sink faucets, 3/8“ supply tubing and basket drain now, before dropping the sink into place. ...
  9. Finishing Installation & Care

Part of a video titled How To Install a Countertop End Cap - YouTube
4:06
7:25
And for your reference the iron is set on cotton. You also want to have a rag a damp rag to coolMoreAnd for your reference the iron is set on cotton. You also want to have a rag a damp rag to cool down the glue. And also to apply pressure along the entire end cap.

Full Answer

How do you glue a laminate countertop end cap?

Brush a layer of contact adhesive over the buildup strip and the back of the laminate endcap. Allow the contact adhesive to cure until it becomes very tacky. This will take between 10 to 20 minutes depending on the humidity and temperature of the room. Center the endcap over the end of the counter and press it into place.

How to install countertops with end caps?

Pour a long layer of wood glue along the edge of the countertop, where the end caps have to be installed. Step 2: Upon the glued countertop surface, press the extended wooden strip for increasing the width of the countertop’s edge.

How do you cover a laminate countertop that has been cut?

Cover the cut area with a laminate endcap that matches the surface of the laminate countertop. Place the countertop on a flat and stable work surface. Position the countertop so the end requiring the endcap has easy access. Cover the exposed end of the countertop with a layer of wood glue.

How do you use an end cap?

An end cap is nothing more than a rectangular strip of laminate that is cemented to the edge. In order for the laminate cap to cover completely, it must be slightly larger than the raw edge. When it is glued on it leaves an abrupt edge on top. A file is then used to round and smooth the sharp edges off the end cap. Hold the file in one hand.

image

How do you install an end Splash kit?

1:216:25How To Install Formica End Caps On A Bathroom Vanity - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this is a countertop in splash kit. And as you can tell this right here will match the bull noseMoreAnd this is a countertop in splash kit. And as you can tell this right here will match the bull nose. And then this will match the other end as it curves down.

How do you seal the end of a laminate countertop?

0:022:02Formica LifeSeal Worktops: Sealing the Edges - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe join between the wall and the worktop itself will need to be sealed too on the top only withMoreThe join between the wall and the worktop itself will need to be sealed too on the top only with acrylic.

How do you cut a laminate countertop end cap with a router?

0:359:04How to apply a counter top end cap. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first step is to apply these sticks. I have already opened a pack of sticks I've already preMoreSo the first step is to apply these sticks. I have already opened a pack of sticks I've already pre started my nails. And these are print cut to size for this collar.

How do you cover laminate countertop edges?

2:159:16How to install laminate countertop edge strips- Episode 4 - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsually you can just buy an end cap kit that you'll see underneath. Or somewhere near the laminateMoreUsually you can just buy an end cap kit that you'll see underneath. Or somewhere near the laminate countertops in the store.

How do you finish the edge of a Formica countertop?

0:452:26how to FINISH a formica countertop laminate edge - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo on the inner corners here we'll try to rough it out with a flat file and then around the cornerMoreSo on the inner corners here we'll try to rough it out with a flat file and then around the corner and clean it up with the smooth file and then use a sanding block.

Are you supposed to seal laminate countertops?

When looking to update or overhaul a countertop, use a resin, acrylic or polyurethane coating that's specifically labeled for use as a laminate countertop sealant. Polyurethane coating or a resin laminate sealer will provide shine and a protective coating.

How do you attach end cap to countertop?

1:537:25How To Install a Countertop End Cap - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then also I put a little wood glue between the filler strip and the backside of the countertop.MoreAnd then also I put a little wood glue between the filler strip and the backside of the countertop. Then for your larger filler strip. Again if you have a one inch spacing all the way down.

What kind of router bit do I need for laminate countertops?

The square bearing (SQB100 or SQB102) is manufactured with a strong non-stick Teflon® which won't mark your edge so it can be wiped clean easily. CMT's 3 in 1 carbide-tipped flush trim bits with patented Delrin® triangular bearings (791.042. 00 or 791.043. 00) are best for laminate trimming.

How can I cut laminate without chipping?

1:333:38No fuss way to cut laminate sheeting without chipping. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe round part of the trimmer rides on the straight edge of the plywood. And the cutter doesn'tMoreThe round part of the trimmer rides on the straight edge of the plywood. And the cutter doesn't extend very far plus the bed plate on the router say. It only cuts through the laminate.

What is the most popular edge for laminate countertop?

BullnoseThe truth is that Bullnose is one of the most popular laminate countertop edge options.

How do you hide a gap between countertops and walls?

0:423:55Caulking gaps between countertop and wall - YouTubeYouTubeStart of suggested clipEnd of suggested clip1 inch tape you can use you know 3/4 you can use a wider. If you want and I took that and ran it toMore1 inch tape you can use you know 3/4 you can use a wider. If you want and I took that and ran it to the exact height to the countertop on the wall. And then. I took another piece of tape.

How do you seal a laminate countertop seam?

2:468:06Counter repair, how to fill countertop seams with caulk - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply a decent amount of caulk to the entire. Seam. Then you can use your finger or a putty knife toMoreApply a decent amount of caulk to the entire. Seam. Then you can use your finger or a putty knife to push the caulk into the. Seam.

How do you hide a laminate seam?

Apply a small amount of seam filler on the plastic plate. Use your putty knife to mix the filler until the color is consistent. Scoop putty onto the edge of your putty knife and drag the knife across the seam. Repeat this step until the seam is filled.

Can you put polyurethane on laminate countertops?

Apply polyurethane layers. Paint three coats of polyurethane on the kitchen countertops to seal the surfaces. Choose a satin or glossy polyurethane to give the kitchen laminate countertops a high-end look and feel. Allow each layer to dry between coats completely.

Is there a sealer for Formica countertops?

Formica Countertop Sealer A gel gloss for laminate countertops is a nonharmful, abrasive cleaner that removes pesky surface scratches and oxidation offers a protective wax coating and a high-gloss finish.

What is an end cap on a countertop?

How to File Laminate Countertop End Caps. End caps are cemented to the ends of countertops where the laminate is routed off, leaving a raw, exposed end of particleboard or plywood. An end cap is nothing more than a rectangular strip of laminate that is cemented to the edge.

How to file laminate edges?

Pull the file downward slowly over the edge of the laminate. You will feel it begin to file the edge. Don't pull too fast; just use an even consistent movement downward. Don't file with an upward motion, this can cause chipping of the surface laminate.

How to polish off rough spots on laminate?

Slide the paper along the edge of the laminate from side to side to polish off any rough spots left over from the file. Use the finest tooth file that you can find. When installing the end cap, try to get it on as straight as possible to keep filing to a minimum.

How to polish laminated wood?

Sand the edge of the laminate, using a light touch, with a folded piece of 180-grit sandpaper. Slide the paper along the edge of the laminate from side to side to polish off any rough spots left over from the file.

Why do you need end caps on kitchen countertops?

Such edges are created because countertops are usually mechanically fitted and do not come in custom-made sizes. The degree of exposed surface of the countertop directly affects the number of end caps you will need to secure the edges.

How to use jelly on laminate countertop?

Using your router, trim away the excess caps from the edge of the countertop. With the file, smoothen the small edges that are visible around the end caps. The best way is to file towards the countertop to ensure that the end caps do not chip.

What are end caps used for?

Generally, manufacturers supply pre-shaped end caps to cover the countertop’s finished edges but end caps that are self-installed using the plastic laminate strips are regarded as the best in terms of durability and for lending a firm grip to the countertop.

Laminate end caps

We are remodeling a kitchen in a house that we will probably only live in for a few years and eventually become a rental property. We have picked out laminate countertops, and are planning to have Lowe's do the install. The contractor came to measure for them, and I asked about how they would do the corners/edges on the island/bar.

Comments (12)

Granite will be just about as cheap as installed laminate. It will be far more durable as well.

How to file a laminate countertop?

Lightly file and round the cut edge, using a flat file. File toward the countertop to avoid cracking or chipping the laminate.

How to stop laminate from burning?

Trim the excess laminate from the endcap. Apply a layer of petroleum jelly or other lubricant along the cutting line of the endcap to prevent friction burns. Cut through the laminate with a flush trim router bit.

How to prevent laminate burns?

6. Trim the excess laminate from the endcap. Apply a layer of petroleum jelly or other lubricant along the cutting line of the endcap to prevent friction burns. Cut through the laminate with a flush trim router bit.

How long does it take for laminate to cure?

Allow the contact adhesive to cure until it becomes very tacky. This will take between 10 to 20 minutes depending on the humidity and temperature of the room.

Is laminate countertop available?

The availability of laminate countertops is plentiful in today's society. The multiple colors and finishes of the laminate allow homeowners the opportunity to install a countertop that compliments their decor. Many home improvement centers have sections of laminate countertops for sale and will cut the sections to the desired dimensions.

Does laminate come with buildup strip?

Custom-ordered laminate countertop will come with a buildup strip and laminate endcap. The pieces also are sold separately.

How to fix pencil line on side splash?

Apply construction adhesive or silicone caulk to the entire inside of the pencil line on the side splash.

What is an end splash?

An end splash is installed on any laminate counter that stops at a wall or cabinet and covers any irregularities between the counter's edge and the wall. If both ends of the counter meet a wall, you have two end splashes. Installing the end splash is identical to installing the backsplash and requires only adhesive. Advertisement.

How to apply end caps to laminate?

To apply end caps using non pre-glued end caps, apply a contact adhesive to both the substrate and the laminate. Follow manufacturer's guidelines for when adhesive is ready for bonding. Roll laminate with a J-roller. Finish trimming with a fine file, applying only pressure in the up strokes.

How to apply end caps to kitchen counter?

To apply end caps, set household iron at medium heat. Iron cap onto the end of the countertop with a back-and forth motion . Let set for one minute, then tap the cap carefully with a rubber mallet. Finish trimming with a fine file, applying pressure only on the up strokes.

How do I install a range top?

Always follow manufacturer's directions for Installing appliances. Place the sink or rangetop rim on the back side of the countertop, where the appliance is to be located. Mark all the way around the edge of the rim. Use a jig saw to cut the hole 1/4" to 3/8“ smaller than the line. All cutout corners should have clean, chip-free radii. Apply two layers of heat-conductive aluminum tape around rangetop cutout.

How to scribe countertop to wall?

Place the top on the cabinet. Use a scriber-compass to mark the top edge of the countertop, then belt-sand or block-plane to the line. This will contour the countertop to the wall. Put top in place, check for level and stability, and then secure to cabinets with wood screws.

How to cut Formica laminate?

Cover the Formica ® brand laminate surface in the area to be sawed with a strip of masking tape and draw a pencil line on the tape to serve as your cutting guide. Use a fine-tooth handsaw (10 to 12 point) and always cut into the laminate surface to avoid chipping. Sand or file the cut to ensure a smooth surface.

What is your responsibility when installing Formica?

Caution: Safety is your responsibility. Exercise care with tools when installing Formica ® brand products.

Where should end caps be used?

End caps should be used on all exposed ends (end cap kits ). End splashes should be used where top butts wall (end splash kit). Additional material should be allowed to scribe for a tight fit to end wall. Step 2: Cutting.

image

1.Videos of How Do You Put End Caps On Laminate Countertops

Url:/videos/search?q=how+do+you+put+end+caps+on+laminate+countertops&qpvt=how+do+you+put+end+caps+on+laminate+countertops&FORM=VDRE

2 hours ago  · Hand File Set: https://amzn.to/3lEeCEZThis video covers my first attempt at installing a laminate countertop end cap. I am not a pro but that is the whole...

2.How To Install a Countertop End Cap - YouTube

Url:https://www.youtube.com/watch?v=1D80V3clMnQ

28 hours ago  · Learn how to make and install a laminate countertop end cap from an offcut. This detailed step-by-step tutorial walks you through the entire process from st...

3.How To MAKE and Install a Countertop End Cap - YouTube

Url:https://www.youtube.com/watch?v=z4u7E909OmY

34 hours ago You people don't understand how laminate counters are built. You take a sheet of laminate and fold it over particle board, just like starting to wrap a present. It can only fold over the back and the front. It doesn't fold over the side. It can't. The slabs with the particle board sides are then cut to size, and capped with a flat piece.

4.Adding End Caps On A Countertop | DoItYourself.com

Url:https://www.doityourself.com/stry/adding-end-caps-on-a-countertop

1 hours ago  · How to Trim the Endcap of Laminate Countertops 1.. Place the countertop on a flat and stable work surface. Position the countertop so the end requiring the endcap has... 2.. Cover the exposed end of the countertop with a layer of wood glue. Center and press the buildup strip into place. 3.. Brush a ...

5.Laminate end caps - Houzz

Url:https://www.houzz.com/discussions/4134911/laminate-end-caps

31 hours ago Warm up the flat iron to a medium heat. Hold the end cap in place next to the countertop, with the adhesive facing in toward the battens. Run the warm iron over the end cap piece to activate the adhesive. When done correctly, the adhesive should not stick to the iron.

6.How to Trim the Endcap of Laminate Countertops

Url:https://homeguides.sfgate.com/trim-endcap-laminate-countertops-27338.html

10 hours ago Step 1. Lay the main countertop on sawhorses so you can access the side where you are installing the side splash. Hold the side splash up to the side of the counter with the laminate facing toward the counter. Ensure the front and bottom edges of the side splash align perfectly with the counter.

7.How to Install Laminate End Splash on Countertops | eHow

Url:https://www.ehow.com/how_12208399_install-laminate-end-splash-countertops.html

15 hours ago

8.How to Install Laminate Countertops | Formica

Url:https://www.formica.com/en-us/articles/inspiration/how-to-install-a-preformed-countertop

11 hours ago

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9