How To Glitter And Resin A Tumbler
- Step 1: Wash the bottle Wash your bottle surface with soap and water to ensure it is free of grease and debris. ...
- Step 2: Add tape Apply painter’s tape to both ends of the tumbler. ...
- Step 3: Coat with glue Use your foam brush to apply glue to a section of the bottle.
- Step 4: Add glitter ...
- Step 5: Add epoxy ...
- Step 6: Remove tape
How to make Glitter tumblers?
How to Make Glitter Tumblers Step 1: Prepare and tape your tumblers for the glitter.. Note: Details on these steps are in my step-by-step video! Take... Step 2: (Optional) Spray paint your tumblers.. You can paint your tumblers, and I did this with three different kinds of... Step 3: Put adhesive on ...
How do you apply glitter to epoxy tumblers?
Apply the epoxy to the tumbler using gloved hands, spreading it evenly over the entire painted surface. As soon as you have an even coat, it’s time to apply the glitter!
How do you add glitter to acrylic?
I found the easiest way to do this was by taking a small craft knife blade and running it around the edge to remove the 'fluffy' bits of acrylic and then turn the tumbler the right way up and shake it until any other little bits of acrylic fall out. It's not the most technical way of doing things, but it works! Step 3. Adding the Glitter
How do you keep Glitter Tumblers from Drip?
While the epoxy on your glitter tumblers is curing, you need a way to suspend your tumblers and keep them turning so they don’t drip. You can do it the low-tech way with a cardboard box, some PVC pipes, some dollar-store footballs, and duct tape, or you can step up your game with a tumbler turner we built from a rotisserie turner.
How do you get glitter to stick to a tumbler?
In order to make the glitter stick to the tumbler, I prefer to use Mod Podge over spray adhesive since it's less messy! I put a little bit of Mod Podge in a separate bowl and use a flat paintbrush to put it on. I “paint it on” so that the whole mug is covered in a uniform and smooth layer.
What do you use to apply glitter to a tumbler?
There are several ways to add glitter to a custom tumbler - I went with the Mod Podge method. You can also use a thin layer of epoxy which I'm sure would give you a much more even glitter layer.
Do you have to spray paint a tumbler before glitter?
The first thing you want to do is to spray paint your tumbler. While technically not required, this is good for two reasons: Spray painting gives the glitter a different surface to adhere to; stainless steel is often smooth and stuff doesn't stick to it.
How do you apply glitter to vinyl tumbler?
3:138:02How To Sand, Apply Decals, Finish Epoxy Glitter Tumbler - YouTubeYouTubeStart of suggested clipEnd of suggested clipTape. Apply the decal to the tumbler. This tumbler. Stand is totally optional but i find it helpfulMoreTape. Apply the decal to the tumbler. This tumbler. Stand is totally optional but i find it helpful for keeping the cup still and straight while i apply burnish the decal with the scraper.
How many layers of glitter does a tumbler need?
Brush the adhesive over the first layer of glitter in a thin, even layer. Coat in glitter and set aside for 30 minutes. Brush off excess. Repeat these steps until your desired level of glitter is achieved (We did 3 coats of glitter total).
How do you seal a glitter tumbler without epoxy?
There are various ways on how to seal a tumbler without using epoxy. You can apply CrystaLac, Mod Podge, or a clear acrylic spray instead. All have advantages and disadvantages, so choose the one that's most convenient for you.
What is the best adhesive for glitter tumblers?
Aleene's, Elmers and Mod Podge are all good options for clear glues. Craft Gliltter: Dries clear is best to avoid bleeding. Polyester Glitter: Dries clear is best, but white works with many of the kinds and colors.
What kind of spray paint do you use for tumblers?
Rustoleum 2x Paint and Primer This is hands-down by far the best spray paint for tumblers. It gives great coverage, comes in loads of colors, and dries quickly. Well, the flat dries quickly. The satin and glossy options do tend to take a little longer to dry than the flats, but still worth it.
What kind of paint can I use on tumblers?
Stainless steel spray paint is easy and cheap to use! Make your own DIY custom tumblers with any color paint you want.
How do you seal glitter?
Luckily, it is very easy to seal the glitter onto your ornament. You can paint a thin layer of a glossy mod podge over the areas of glitter and let that dry. Alternatively, you can use a glitter sealer like Krylon's glaze spray for a high-gloss permanent finish.
Do you need to seal vinyl on tumblers?
Many crafters say vinyl doesn't need sealing because most types of vinyl are waterproof or water-resistant. These types of permanent vinyl can last for years, which is true by the way. If you want to create more long-lasting vinyl mugs and tumblers, you might want to consider applying some sealant.
How do you Modge Podge glitter tumbler?
0:088:24How To Glitter A Tumbler | Mod Podge Method - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a paintbrush this is a 3/4 inch flat paintbrush I get from Walmart you can either use a foamMoreUse a paintbrush this is a 3/4 inch flat paintbrush I get from Walmart you can either use a foam brush or whatever you're more comfortable. Using sandpaper I'm using 240 grit.
What kind of spray paint do you use for tumblers?
Rustoleum 2x Paint and Primer This is hands-down by far the best spray paint for tumblers. It gives great coverage, comes in loads of colors, and dries quickly. Well, the flat dries quickly. The satin and glossy options do tend to take a little longer to dry than the flats, but still worth it.
How do you Modge Podge glitter tumbler?
0:088:24How To Glitter A Tumbler | Mod Podge Method - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a paintbrush this is a 3/4 inch flat paintbrush I get from Walmart you can either use a foamMoreUse a paintbrush this is a 3/4 inch flat paintbrush I get from Walmart you can either use a foam brush or whatever you're more comfortable. Using sandpaper I'm using 240 grit.
What kind of epoxy is used for tumblers?
1. ENVIROTEX LITE EPOXY RESIN For Tumblers. Envirotex Lite is a brand of epoxy resin you can use for tumblers, whose claim to fame is that it is a pour-on, high gloss finish. It cures to a thick, glossy coating in about 8 hours at 70F, and reaches full cure in about 48 hours.
How do you use epoxy glitter?
1:5014:11DIY: How to Apply Glitter with the Epoxy Method - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut um basically you're just going to apply a very very thin coat just enough to cover yourMoreBut um basically you're just going to apply a very very thin coat just enough to cover your stainless steel tumbler. Or whatever you're using to apply it.
How to make resin glitter?from artresin.com
Wearing gloves, carefully measure and mix your ArtResin according the instructions. Divide among the 5 plastic shot glasses, one per colour, reserving some clear resin in your mixing cup. Add your tint to each cup, as above, mixing thoroughly. If desired, add glitter to your resin for a sparkle effect! 2.
How long does it take for glitter to dry on a tumbler?from artresin.com
Turn the rotisserie motor on and, with the tumbler turning, slowly pour the ArtResin onto the surface of the tumbler as it turns, smoothing it out with your gloved hands. Once the entire surface has been evenly covered, allow it to turn until it is dry to the touch, within 18-24 hours. Once dry, remove the tape and allow it to finish curing. At 72 hours, it will have fully cured.
What is an Epoxy Tumbler?from upstartepoxy.com
Quite simply, an epoxy tumbler is a tumbler that has been decorated using epoxy. The benefits of using epoxy is that it is a durable finish, one that won’t chip away over time.
How long does it take for a tumbler to cure?from artresin.com
Ensure your tumbler has fully cured for 72 hours before use. Ensure there are no traces of epoxy left around the lip of your tumbler. Use sandpaper or a blade to remove any resin that may have seeped under the tape: remove any sanding dust by wiping with a damp cloth. Wash your tumbler in warm, soapy water before use.
Why use an insulated tumbler?from artresin.com
If you're planning on using your tumbler for hot beverages, an insulated tumbler will keep the exterior of the tumbler cool. For this same reason, it's ideal to choose a tumbler with a plastic lip at the top so that the resin won't have to come into contact with a hot beverage.
How to make a tumbler out of resin?from artresin.com
Here's what you'll need: 1 ArtResin epoxy resin 2 an insulated tumbler ( stainless steel is best as epoxy resin doesn't adhere to plastic ) 3 painter's tape 4 spray paint 5 craft materials of your choice to decorate your tumbler: glitter & spray adhesive, alcohol ink & sponges, ResinTint liquid colorant 6 nitrile gloves 7 plastic mixing cups and stir sticks 8 plastic drop sheet to line your work surface 9 a small foam football 10 a cup turner made from a Universal Rotisserie assembled onto a wood base
How to spice up tumblers?from upstartepoxy.com
Two things you can do to further spice up your tumbler are adding more glitter and placing decals.
How to make glitter tumblers?
Step 1: Prepare and tape your tumblers for the glitter. Note: Details on these steps are in my step-by-step video! Take off all of the labels and wash your tumblers. You may also wish to sand the outside of your tumbler, as may help any paint you apply stick to it better.
How to keep glitter tumblers from dripping?
While the epoxy on your glitter tumblers is curing, you need a way to suspend your tumblers and keep them turning so they don’t drip. You can do it the low-tech way with a cardboard box, some PVC pipes, some dollar-store footballs, and duct tape, or you can step up your game with a tumbler turner we built from a rotisserie turner. I show you both up close in the video linked below.
How to apply mod podge to tumbler?
To apply the Mod Podge, get a brush and put the Mod Podge on your tumbler in nice, even strokes. Make sure you don’t have too much globbed on in one section or the other.
What to wear when sanding tumblers?
Be sure to wear a respirator and gloves when you sand your tumblers to avoid epoxy contact, buildup, and potential allergic reaction.
How long to wait after applying glitter to tumbler?
And when you put on your epoxy, you need to have things a bit more in control. Wait about 30 minutes after applying sealer to your glitter tumbler before moving on to the next step.
What to do after taped tumbler?
After you’ve taped everything, you need to wipe the surface of your tumbler down with alcohol. This is important to get any dust or impurities, especially the adhesive from the labels, off of your tumblers. You want everything to stick, and the cleaner the surface of your tumbler is, the more likely that is to happen.
How much resin do you need for a tumbler?
For these big tumblers, I used 25 milliliters of the A bottle and the B bottle for my resin. If you have smaller ones, you could do less. Note that the A bottle is a lot thicker, so don’t be surprised by that. Make sure you have a good supply of plastic cups and Popsicle sticks on hand for mixing, because it’s really important that you mix your resin well.
Why make a DIY glitter tumbler?
As a lot of you guys know, a few years ago I stopped going into the office and transitioned into this strange state of being a work-at-home-mom.
Why is glitter tumbler so hard to make?
Some people find making glitter tumblers to be difficult because of all the waiting involved, they haven’t worked with epoxy before, or they don’t have a cup turner.
Why spray paint on tumblers?
The reason we’re starting with spray paint is that glitter will pop a lot more on epoxied tumblers if there’s a base coat of color on it. I prefer using matte paint because the epoxy will bring out a lot of shine, but play around with it, this is DIY!
How to make a tumbler turner?
Step 3 – Prepare your turner. Step 4 – Mix and add epoxy resin. Step 5 – Apply glitter. Step 6 – Optional: apply vinyl decal or more glitter. Step 7 – Apply the final coat of epoxy. Step 8 – Clean the tumbler and remove the tape. What to avoid. How to make your own epoxy tumbler turner. Conclusion.
How to get glitter off of a carpet?
Make sure you have something underneath the work area, like a newspaper or drop cloth. Work in an area where clean up is easy, where there are hard surfaces. Avoid carpet if you can, and working outside or in the garage is great. Lint-rollers make fast work of fine glitter if you have some spots you need to touch up.
How long does glitter dry?
Since I like a layered look, what I do is let it dry for around 12 hours, then apply more epoxy to the area I want to cover and add another layer of glitter. If you want to save time, do it all at once.
Can you use modge podge on tumblers?
Mod Podge can be really streaky and thick when applying, so we’re going to use the same epoxy we’re coating the tumbler with. If you have a spray adhesive, I’d go right ahead and use that. Similarly, if you have Mod Podge and are a master at applying it, it should work just fine.
STEP 1: TAPEING OFF THE ENDS
Most epoxies are not FDA approved so putting your mouth on the rim of a tumbler that’s epoxied might not be such a great idea. Now this step is not an absolute must especially if you’re using the lid and/or straw so your mouth never comes in contact with epoxy itself. Just keep this in mind when starting your cup.
STEP 2: SPRAY PAINT
Once everything is taped off where you would like it’s time to add the spray paint. You can just lay out a piece of cardboard and set the cup on top of it to spray. I find it easier to use the PVC pipe from the cup turner to spray the cup.
STEP 3: TIME TO ADD THE GLITTER
When adding glitter to your tumbler you want to use something underneath your cup to catch the glitter that falls off such as a piece of paper, a paper plate, a tray and so on. It’s whatever you prefer or is handy at the time.
STEP 4: EPOXY 1 ST COAT
Now that your spray paint and glitter are dry it’s time to epoxy. Attach your PVC pipe with your cup in the turner. Mix a small amount of epoxy using your disposable cups and stir sticks. Flip the switch on the turner to start rotating.
STEP 5: SANDING
When the first layer of epoxy is cured you can use a 220 grit sandpaper and sand the entire outside of the cup until it is smooth. I know what you’re thinking “it’s all scratched up now” just trust me it will look nice and shiny again. Then you want to rinse it off or take alcohol and wipe it down to remove any dust.
STEP 6: VINYL DECALS
By this point, you should already have an idea of where you want your decal. If you even want a decal that is, you may like it with just the glitter. You can skip this step if that’s the case. But if you would like a decal or name decal let’s get to it.
STEP 7: EPOXY 2 ND COAT
Place your cup back on the cup turner and mix up another small batch of epoxy. Spread another thin even coat over the cup ensuring no spots are missed. Leave on the turner to spin for another 12 hours and can hang dry until completely cured. I’d say that 24 hours is the standard.
How to add glitter to tumbler?
You want to slowly add the glitter to your tumbler by pushing it into the hole you've made in the base. This is another step where slow and steady is the way to go - I found that pouring a little glitter onto the bottom of my tumbler and then tapping the side of it helped a lot to fall in, and then could use some craft tweezers to push the rest through.
How to know if you have enough glitter in a snow globe tumbler?
To see if you've added enough glitter to your snow globe tumbler, you want to give it a shake ( remember to cover the hole!) and see how well the glitter disperses. The amount of glitter to use in a tumbler is entirely personal preference, but I found mine looked best when I had a nice even coverage of glitter like the picture below shows.
How to get acrylic out of tumbler?
I found the easiest way to do this was by taking a small craft knife blade and running it around the edge to remove the 'fluffy' bits of acrylic and then turn the tumbler the right way up and shake it until any other little bits of acrylic fall out. It's not the most technical way of doing things, but it works!
What is the liquid in a tumbler?
The liquid for our tumbler is a mix of 50/50 water and vegetable glycerin. It's better to have more than enough than not enough, so I'd suggest mixing 50ml of vegetable glycerin with 50ml of water in a clean cup.
How to smooth tumblers?
Apply your design to the tumbler and carefully smooth it down, making sure to work from the center out to eliminate any air bubbles.
How to minimize air bubbles in tumbler?
To minimize air bubbles, you can tip your tumbler slightly so that the liquid runs straight down the sides of the cup rather than pooling on the top surface.
Can you use glitter on a wedding date?
They'd also work really well as wedding keepsakes or gifts - change the glitter up to match the wedding's color theme, and then vinyl the wedding date with a bridesmaids name along the front!
Can you make glitter tumblers with Mod Podge?
You can make shimmering tiki drinks with glitter, or you could make a glittery cocktail with your favorite drink. You could even make your own glitter! The glitter is easy to make, though you will need to buy some ModPodge. If you want to try it out, you might want go to Modpodge website and order a sample.
Why is my glitter tumbler bumpy?
This happens because of anything falling into the mold while the wax is curing. Skip down below if this is the case. Otherwise, continue to read. You can also skip to section #5 if the problem is caused specifically by the glass. There are a few things you should know about this issue.
How much glitter do you put in a snow globe tumbler?
Using this method, you will need to add a little bit of glue to get the glitter out. You can add more glue if needed. Once you’ve got the glue out, add the water and stir until it comes together. Then add about 1 inch of snow. This will make the snow stick to itself. After adding the rest of your glitter, pour the mixture into your tumbling ball.
Can you seal a tumbler without epoxy?
You can seal any tippling tipple with ModPodge, no matter how fancy it looks. If you want to add a little extra flair to your drink, you don’t have too much to worry about. You don‘t need to spend hours trying to get the perfect seal, just use Modpodge and wait until it drizzles down. And if it doesn’t work, well, that’s fine too.
How much epoxy do I need for glitter tumbler?
Second you’ll want 1mL for each ounce. For example Mix 20ml for 20oz tmbler, 30ml for 30oz, etc. You can also use 1/4 teaspoon for 1 oz. If you don’t have a spoon, use a teaspoon. Just be sure to stir the resin until it dissolves. Then add the glitter and stir again. This is how you make a glitter bottle. Make sure you’re using the right size.
Can you make glitter?
Can you create glitter;. Make glitter by mixing food colors in bowls and adding sea salts. Spread the colors out onto baking sheets and sprinkle with sea salts. Bake at 300 F until the glitter is dry. Then use to decorate cakes, cookies, or other baked goods. You can also use it to make jewelry.
Why does my epoxy tumbler have dimples?
Dimple are caused when the resin is heated too much and the polymerization process is interrupted. This can happen when you over torch the epoxies too fast. You can avoid this by keeping the curing temperature stable and by using a cover. If you torch too light, you might get dimple.
