Sixteenth or 1/16”: The shortest line on the imperial measurements indicates a 16th of an inch and doesn’t normally have a fractional representation. Read a tape measure’s incremental marks for the metric system. Meter or 1m: The one-meter marking is located at the one 100th centimeter marking or 10th decimeter marking. It is indicated by a 1m.
How do you measure sixteenths of an inch on a tape?
Use the tiny, densely-packed marks for sixteenths of an inch. The shortest lines of all on most measuring tapes are the sixteenth-inch marks. There are 16 of these tiny marks per inch — four in each quarter-inch. Note that some very precise measuring tapes will mark down to one-thirty-second of an inch or even one-sixty-fourth of an inch!
How do you read a 1/2 tape measure?
To learn how to read a tape measure to find 1/2 inch increments, locate the second-largest marks – they each correspond to 1/2 inch. To find 1/4 or 3/4 on a tape measure, locate the third-largest marks. They each correspond to 1/4 inch, with the longer 1/2 mark where the 2/4 inch mark would be.
How to read an imperial tape measure?
How to Read an Imperial Tape Measure 1 1 foot = 12 inches 2 1 inch = 16 x 1/16th of an inch, 8 x 1/8th of an inch, 4 x 1/4 of an inch or 2 x 1/2 of an inch. More ...
What do the numbers on a tape measure mean?
On every tape measure, there are both small and large tick marks and sometimes numbers. The biggest tick mark usually denotes inches, the second biggest denotes 1/2 inches, and so on. The largest numbers correspond to inches, with fractions of inches being in between each of the largest numbers.
Where is a 16th of an inch on a tape measure?
0:091:20How to Measure Sixteenths on a Ruler : Math Measurements - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn a ruler. So measuring 16 is actually going to be pretty easy because the ruler between inches isMoreOn a ruler. So measuring 16 is actually going to be pretty easy because the ruler between inches is split into 16 lines. So if this is my let's say this is my 1 inch mark.
What does 16 inches look like on a tape measure?
0:163:15️HOW TO READ 16" ON CENTER LAYOUT ON MEASURING TAPE ...YouTubeStart of suggested clipEnd of suggested clipSo you have 3/4 inches on each side of your Center mark 16 inches will be a Cinemark of your 2x4MoreSo you have 3/4 inches on each side of your Center mark 16 inches will be a Cinemark of your 2x4 vertical member in your wall.
How big is 16th of an inch?
1:228:27Reading a Ruler to a Sixteenth of an Inch - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is 1/8 2/8 3/8 4/8 because for ages 1/2 5/8 6/8 7/8 and then the smallest line here these areMoreThis is 1/8 2/8 3/8 4/8 because for ages 1/2 5/8 6/8 7/8 and then the smallest line here these are your sixteenths of an inch this is one 16 to 16 3/16 4 5 6 7 this is 8 16. Which is the same as 1/2.
How do you measure 1/16 of an inch?
0:502:15How to measure to the nearest 1/16 of an inch - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd when i zoom in towards the end here I can see that at the end I have one tick mark past theMoreAnd when i zoom in towards the end here I can see that at the end I have one tick mark past the three inch mark. That means that this line is actually three. And one sixteenth of an inch. Long.
What is the meaning of 16 inch?
Most tape measures are marked in sixteenths of an inch, which is written 1/16 or 0.0625 inches. Note that 0.75 inches is 12/16 of an inch, and 0.77 is very close to that amount.
How do you read a tape measure for dummies?
0:583:20How to Read a Tape Measure - REALLY EASY - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe can call these one quarter two quarters referred to as half an inch three quarters. And theMoreWe can call these one quarter two quarters referred to as half an inch three quarters. And the fourth quarter is the next inch every fraction on the tape measure has a preferred written form.
What is a 16th of an inch in decimal?
Decimal Value of an Inch. 1/16. 0.0625. 1/8. 0.125.
Why is there 16 in an inch?
Each inch is divided into 16 lines, meaning that the space between each line is 1/16 inch long—this is the smallest length you can measure with a ruler.
What is a 16th of an inch in MM?
1.57 mmConversion table inches to mmDimensions — Inches to MetricDecimal InchesFractional InchesMetric0.031”1/32”0.79 mm0.062”1/16”1.57 mm0.125”1/8”3.18 mm21 more rows
What is smaller than 1/16 of an inch?
Fraction Conversion TableFractionDecimalMillimeters1/320.031250.7933/640.0468751.191/160.06251.58761 more rows
How many 16ths are in a quarter inch?
Answer and Explanation: There are 4 sixteenths in one-fourth.
Why is 16 and 32 on tape measure?
Standard US construction practice separates wall studs by 16 inches. Marking these on the tape makes it easier for the carpenter to see the relevant multiples.
Why is 16 red on a tape measure?
The red indicates 16-inch-on-center spacing. This is a common framing spacing for wall studs, floor joists and common roof rafters. If you decide to space framing at 24-inch centers, the red marks will be at every other foot marking on the tape measure.
Why is there 16 in an inch?
Each inch is divided into 16 lines, meaning that the space between each line is 1/16 inch long—this is the smallest length you can measure with a ruler.
Which side is inches on a measuring tape?
Most tapes feature imperial units (inches) on the top row and metric units (centimeters) on the bottom.
How to read imperial tape measure?
How to Read an Imperial Tape Measure. To know how to read a tape measure, you need to consider switching from long marks to short marks. The longest mark indicates one inch. The shorter the length of the markings, the shorter the dimensions. Markings range from 1 inch to 1/16 inch on most tape measures.
How many feet are there in a tape measure?
Usually (but not always) after every 12 inches you will find a one foot mark . This usually has a different color from the other marks, it is usually red, unlike normal black marks. After each foot mark, the numbers following each inch mark will repeat from 1 to 11 again or follow the count . This can vary for each tape measure.
What is a tape measure?
First and foremost, a tape measure is a compact tool that is used to measure lengths and distances. The tape is made of a flexible material and has a scale. To measure, you lay out the tape along the corresponding route and then read off the scale. For the result to be correct, the tape must of course be stretched and laid straight.
What is the largest mark on a tape measure?
Use the large number markings for the inches. On a tape measure with imperial units, the largest marks are usually the 1-inch marks. These are usually marked with long, thin lines and fairly large numbers as you can see in the image above. Usually (but not always) after every 12 inches you will find a one foot mark .
What is the function of a box tape measure?
We know as a box the part of the tape measure that holds the tape , which can be made of plastic or metal. Its function is to prevent the spiral tape from expanding. On the other hand, at the back of the shell we will find a clip that is used for the belt, which facilitates access while working.
What is the hook tab on a tape measure?
2. Hook-shaped Pull Tab. This part of the tape measure is what allows it to hook onto the end of whatever you are about to measure. Basically it prevents the tape from staying a part outside the casing when backing up.
What is the yellow spiral rule on a tape measure?
We can basically define the tape as the yellow spiral rule that can be wide or thin.
How to measure length with a metric tape?
To measure with a metric measuring tape, first find the nearest centimetre before the distance you're measuring, then the nearest millimetre. You can use a 0.5 millimetre mark to help guide you if your measuring tape has them.
What are the markings on a tape measure?
Use the big, numbered markings for inches. On a tape measure labeled with imperial units, the most prominent marks are usually the one-inch marks. These are typically marked by long, thin lines and fairly large numbers.
What do the small, densely packed markings for millimetres mean?
3. Use the small, densely-packed markings for millimetres.The small, tight, narrow lines between centimetre markings represent millimetres ( or one-tenth-centimetres). There are ten millimetres in a centimetre (and, thus, one thousand in a metre.)
How to find the accurate measurement of a length?
First, mark the spot where the measuring tape lines up with the edge of the thing you're measuring. Find the nearest inch before this point . Then, find the nearest half-inch before this point.
What is the most prominent marking on a measuring tape?
On most metric measuring tapes, centimetres are the most prominent markings. Centimetres are usually labeled with large lines and, next to each line, a number. As with inches, the line marks each centimetre, not the number itself.
How many tiny marks are there on measuring tape?
Use the tiny, densely-packed marks for sixteenths of an inch. The shortest lines of all on most measuring tapes are the sixteenth-inch marks. There are 16 of these tiny marks per inch — four in each quarter-inch.
How many testimonials does wikihow have?
wikiHow marks an article as reader-approved once it receives enough positive feedback. This article has 17 testimonials from our readers, earning it our reader-approved status.
How many lines are on measuring tape?
Overall, standard measuring tapes show 16 line markings for down to a sixteenth of an inch. And many also show line markings for down to 1/32 of an inch.
What does 15 inches mean?
So, 15″ means 15 inches and 15’ means 15 feet !
Can you memorize tape measure markings?
Anyways, to keep it simple, just use the printable guide and you’ll have the tape measure markings memorized in no time! And you can of course buy an easy read tape measure to make it even easier!
What is a tape measure?
They are among the most common measuring tools used today. Generally speaking, the term “tape measure” refers to a roll-up, self-retracting style tape measure that’s designed for carpentry.
What is the biggest marking on a tape measure?
Find/read the markings. On a standard tape measure, the biggest marking is the inch mark (which generally has the biggest number, if it has them).
How to measure length less than 1 inch?
For a length less than 1 inch, simply read off the tape measure the length. If the increments of an inch are not labeled, determine the marking’s increment and add together the respective fractions.
How to find the length of an inch?
In order to find the length, add the length of the inch (1) with the space between the second inch mark and the third. In this case, you’d add 1 inch + 1/4 inch to get 1¼ inch, or “one and a quarter inches. For a length less than 1 inch, simply read off the tape measure the length.
How to measure length?
Measure a length. Put the end of the measure at one end of the item or space you want to measure. When the length stops, take a reading on the tape measure. Find the length. In order to determine the length, you must add the lengths between inches together.
How to find the distance from 2" to 3"?
Let's start simple. The distance from the 2" to 3" marker is, of course, 1". From the inch mark to the ⅛" mark is ⅛". 1" + ⅛" = 1 ⅛".
How to read half inch?
You can think of a half-inch mark as half way between a full inch.
How to find 1/8 on tape measure?
To find 1/8, 3/8, 5/8, or 7/8 on a tape measure, locate the second smallest marks – they each correspond to 1/8th of an inch. These measurements are the same as 2/16, 6/16, 10/16, and 14/16.
Why Are Some Tape Measure Numbers Red?
The red numbers on a tape measure are an easy way to tell where studs lie. Since most studs are framed at 16″ between the center of each stud (sometimes referred to as 16″ on center), once you find the center of your first stud, using the red numbers, you can find the center of every stud on the wall.
What Are The Black Diamonds and Triangles on Tape Measures?
Black diamonds or triangles are also called truss marks, and they are spaced out every 19 3/16 inches. These measurements are usually used by framers – which is something most DIYers don’t get into. Basically, as a DIYer, feel free to ignore them!
What is an SAE tape measure?
SAE stands for Standard American English units of measurement, though depending on who you ask in the tool world, it sometimes refers to the Society of Automotive Engineers, who helped standardize Imperial measurements.
What is the smallest unit of measurement?
Metric is pretty different from Imperial – while the smallest unit of measurement in Imperial is generally a 1/16″, the smallest in metric is 10mm. There are 16 sixteenths of an inch in every inch, but there are only 10mm in every cm. Yes, metric probably makes a lot more sense on paper, but since the US hasn’t switched yet, most of our measuring tapes will still be Imperial.
How many cm are there in a metric tape measure?
But if you DO end up needing or using a metric tape measure, know that for every meter, there are 100 cm. For every cm, there are 10 mm. Most metric measuring tapes only mark the cm for readability, so you’ll need to count the number of ticks in between to get your exact measurement. Sometimes, there are larger ticks in between each cm to denote 1/2 cm.
What is the most important feature of tape measures?
There are all kinds of add ons and extra features that tape measures can have, but the most important (to me) is a rubberized case, a decent extension length, and numbered markings.
How to use a tape measure?
To use a tape measure, pull the tang out from the housing and hook it on the edge of the object to be measured. Stretch the blade across the object, press the lock, and then observe where the blade meets the end of the object. The nearest line on the blade to the end of the object is the final measurement. Once you have noted it, unhook the tang, holding the blade with your hand so that its recoil won’t cause injury, then press the lock to release the blade. Slowly allow the blade to return to the housing.
How many inches is the first inch on a tape measure?
The first inch on a tape measure is actually short by 1/16 of an inch, because the metal on the tang is exactly 1/16 of an inch. So for measurements taken from the inside edge of an object, such as measuring the length of a wall from corner to corner, the tang slides back against the blade and the metal of the tang is added to account for the “missing” 1/16 of an inch.
How to measure a nail with a pencil?
Using a pencil, mark the initial measurement and keep the tip of the pencil sitting lightly on the surface of the material at this point. Rotate the tape measure in a full 360 degrees, keeping the tang firmly attached to the head of the nail or screw. Complete the rotation and you should have a perfect circle.
What does tang mean on a tape measure?
Tang: The metal clip at the end of the tape, also known as the clip or hook. When reading the tape measure, the tang indicates zero. Lock: The button on the front of the housing locks the tape in place when pressed, preventing the tape from being pulled out further or retracting.
Why are tape measure blades concave?
Tape measure blades are slightly concave to increase the blade’s rigidity when in use . This curve lets the blade be pulled out further without losing stiffness, helping take longer measurements with more accuracy.
What is the measurement of an inch?
Inch or 1”: The inch measurement is the longest vertical line on the imperial half of the blade. This line is indicated by a large number sitting to the left of the line. Example: 1=1”, 2=2”, 3=3”
How to avoid cutting a tape measure too short?
When reading a tape measure, the edge of the object may fall between two lines on the blade. To avoid cutting too short, always round up to the larger measurement. At worst, you will need to measure and cut again, but that is far better than wasting a piece of material that’s 1/16 of an inch too short for your needs.
