how do you rebuild a hayward pool pump

Inside of your pump motor are a front bearing and a rear bearing, attached to the front and rear of the motor shaft (which is attached to the rotor). Rebuild it, with new bearings and shaft seal, or replace it with new motor and shaft seal. Or you can replace the entire pump.

Full Answer

How do you replace a Hayward pool pump?

• Using a flathead screwdriver, begin to pry one side of the lock ring assembly 'out-and-up' towards the top of the body.
• It may take at least 2 or 3 screwdrivers to begin lifting the lock ring assembly over the lip it rides under.
• After clearing the lip at the starting point, begin working your way around the lock ring assembly until you free it.

More items...

How to troubleshoot a Hayward pool pump?

Low readings on the filter pressure gauge

1. Low readings on the filter pressure gauge If your gauge is reading low, it could be due to a clogged skimmer basket or pump strainer. ...
2. Constant leaking We talked about the ways to check for leaks and how to fix them. ...
3. Constantly losing prime

How do you bachwash a Hayward pool pump?

To backwash a sand filter:

• Shut off the system
• Clamp the backwash hose to the water outlet
• Position the backwash valve to either push or pull—the water will flow through the hose or the equipment
• Turn the handle to the backwashing position
• Backwash for a few minutes or until the water clears
• Turn off the system to stop the backwashing process
• Roll up the hose

More items...

How to replace a Hayward pool pump motor?

Pump Replacement. This series of product cross reference charts is intended to help you find the closest suggested Hayward replacement for other manufacturers’ equipment. Recommended replacement product may not be an exact feature match - they may include enhancements.

How do you take apart a Hayward pool pump?

0:471:56Poolandspa.TV Swimming Pool And Spa Pump Repair Series - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay you're going to keep your wrench right there I'll brace against the side here you're going toMoreOkay you're going to keep your wrench right there I'll brace against the side here you're going to turn your pump to the side keeping your wrench there. And then you can grab the impeller.

Can a pool pump motor be repaired?

If you're fairly confident in your DIY skills then you can always do minor pump repairs like changing the mechanical seals or changing your pump bearings.

How much does it cost to rebuild a pool pump?

Replace a Pool Pump: national average costcost to replace a pool pumpNational Avg. Materials Cost per pump$443.54National Avg. Cost (labor and materials) for 1 pump$528.71National Cost Range (labor and materials) for 1 pump$475.73 - $581.696 days ago

What is the life expectancy of a Hayward pool pump?

On average, pool pumps last eight to 12 years before needing replacement. Over time, it's normal for pool parts to begin to wear down.

How do you rebuild a pool pump?

2:5111:43How To Rebuild And Install A Pool Pump Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo just loosen it up and hold the wrench on the back and it'll come right off. You need to removeMoreSo just loosen it up and hold the wrench on the back and it'll come right off. You need to remove the seal. That's on the front of the pump here to split the pump apart.

How do I take apart my pool pump motor?

3:3013:35How to Replace a Pool Pump Motor -The Ultimate Video Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have a pump held on by a clamp like this simply just undo this clamp here and the motor willMoreYou have a pump held on by a clamp like this simply just undo this clamp here and the motor will separate from the pump.

How much does a Hayward pool pump cost?

$500 to $1,200What's the cost of a Hayward pool pump? Hayward pool pumps range from $500 to $1,200. They have a number of single and variable speed models to choose from.

What do I do with my old pool pump?

Pool equipment like pool pumps can't be recycled and are difficult to move and dispose on your own. The easiest, most convenient way to get rid of an old pool pump is to have it picked up and hauled away for proper disposal by the junk removal experts at LoadUp.

What causes a pool pump to go bad?

Usually, it's because of a bad thread sealant, crack in the pump, an air leak in the suction line, a plumbing issues on the suction side of the pump, or a leaky valve stem.

How do you tell if a pool pump is burned out?

0:481:17How Do I know If My Pool Pump Motor Is Burnt Out - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut if you look inside your motor you see color and wire like this that means a coil has burnt outMoreBut if you look inside your motor you see color and wire like this that means a coil has burnt out inside of your motor.

How do I know if my pool pump needs replacing?

Signs You Need Pool Pump ReplacementRumbling Sounds. An excessively-vibrating pump motor can create these rumbling sounds. ... Grinding or Screeching Sounds. ... Blowing Bubbles and Spitting Water. ... Old Age. ... Get a New Pool Pump Now to Keep Enjoying Safe Water.

Can I replace my 1 HP pool pump with a 1.5 HP?

So to answer the question, yes, you can replace your 1hp pool pump with a 1.5hp pool pump, but only if your situation calls for it. If you've determined that your current pump is too small for your pool, then we'll suggest replacing it with a larger ECO pump like the Water TechniX Pump Alpha ECO.