How to Calibrate Aqua Rite System
- Step 1: Test the Pool Water Firstly, you need to test your pool water by using a test strip for saltwater in knowing the salt level of the pool. ...
- Step 2: Change the main switch As the pump is under operation, change the switch to “OFF” from “Auto” position. ...
- Step 3: Recalibrate by pushing the diagnostic button ...
- Step 4: Change the pump’s main switch ...
Full Answer
How to recalibrate Aqua Rite?
Can you recalibrate Hayward Aqua Rite?
Does the Hayward Aqua Rite match the salt level?
Can you add videos to your watch history?
How do you calibrate Aqua Rite salt?
1:022:17Recalibrating an Aquarite Salt Chlorine Generator - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst step slide the main switch to the auto. Position. Second step push the diagnostic button untilMoreFirst step slide the main switch to the auto. Position. Second step push the diagnostic button until a T number appears on the display.
How do you calibrate a Hayward AquaRite salt cell?
Press the diagnostic button 8 times to get to the cell type menu. Flip the switch back and forth between "Super Chlorinate" and "Auto" until you see the correct T-Cell number displayed, and return the switch back to "Auto." Your Hayward AquaRite control unit is now calibrated for use with your new salt cell!
How do I reset my aqua rite?
To reset, turn the unit to Off and then back to Auto. Wait for the relay to click (5 to 10 seconds).
How do you calibrate a Hayward salt tester?
0:001:00Hayward Aqua Rite Salt Level Calibration - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what i do is i turn turn it off. Turn it to the minus zero and turn it up so whatever yourMoreSo what i do is i turn turn it off. Turn it to the minus zero and turn it up so whatever your reading is turn to auto.
How do you reset a Hayward Aqua Logic salt cell?
Press the 'Menu' until, 'Default Menu' appears on the display. This menu is where the 'Inspect Cell' message is stored. Press the (>) key, repeatedly, until 'Inspect Cell, Hold + to reset' appears on the display.
What happens if salt level is too high in pool?
A high salt level can cause your chlorinator to shutdown and may begin to give your water a salty taste. Generally, salt will begin to be tasted at a level of about 3500-4000 ppm. The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming season should be minimal.
How do you know when a salt cell is bad?
Further troubleshooting will be required.If the salt cell bubbles, but only a little bit, then you probably have a bad cell. ... If the salt cell bubbles vigorously, then it is working fine.If the salt cell is good, but you are are constantly getting a zero chlorine reading in the pool, something else is wrong.
What percentage should my salt chlorinator be set at?
Crank up your salt water chlorinator Since it's summer, set your salt water chlorinator to 80% to 100%.
Why is my salt cell reading High?
The “High Salt” light indicates that there is a higher salt level than recommended. The “High Salt” light will stay on for several reasons including: cell amperage is above the maximum limit, the control is set to the wrong turbo cell, or, most commonly, there is too much salt in your pool.
How do I know if my Hayward salt cell needs replacing?
What Are Some Signs That Your Salt Cell May Need Replacing?Looking worse for wear, it's lost a few plates and the acid baths just aren't working.Your pool is starting to turn green or cloudy, even though your chlorinator is turned up to 100%.More items...•
How long does a Hayward salt cell last?
about five yearsWith proper care, a cell will last about five years. Eventually, though, it will need to be replaced. The trick is, it's not always easy to know when it's time.
Why does the salt level in my pool keep going down?
Salt doesn't evaporate or break down, and the salt that a SCG uses to generate chlorine doesn't get used up. So you only ever need to add more salt to a pool when it gets lowered due to dilution of the pool water – typically after large amounts of rain or after partially draining & refilling.
What should my Hayward salt chlorinator be set at?
2700 ppm to 3400 ppmSalt Systems work best with approximately 3200 parts per million (ppm) of salt, which is roughly the equivalent to a teaspoon of salt per gallon. However, all Hayward Salt Systems are designed to operate with salt levels anywhere from 2700 ppm to 3400 ppm.
What should my salt cell be set at?
Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal.
How do I know if my Hayward salt cell needs replacing?
What Are Some Signs That Your Salt Cell May Need Replacing?Looking worse for wear, it's lost a few plates and the acid baths just aren't working.Your pool is starting to turn green or cloudy, even though your chlorinator is turned up to 100%.More items...•
Why is my salt cell not producing enough chlorine?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
Aquarite reading low salt even though salt is high
Hello All, I'm having a problem with my Aquarite and I'm about to leave on vacation in a couple of days! Great timing! It's registering a low salt content. This morning it got as low as 2300ppm. I've been adding salt over the past couple of weeks thinking I was getting low but when I took a...
Aqua Rite salt reading not accurate | Trouble Free Pool
This is an excellent site with a great deal of useful, relevant, and accurate information...thanks so much for keeping it going. My issue...my Aqua Rite T-Cell-15 is reporting only 2500 ppm while my salt test strips show I actually have 3200 ppm. I added salt yesterday while the reading on the...
Why Does Salt Chlorinator Fail?
Your salt chlorinator can fail due to several reasons, the main one being lack of maintenance . When you maintain your system, you ensure that excess calcium does not get stuck on the plates and give a false reading.
How to test salt water in Aqua Rite?
Step One: Test the Water. The first thing is to test the water using a saltwater test strip to know the correct salt level. If you get a different reading from the one on your Aqua Rite, move to the next step. Step Two: Switch the Main Switch.
What is the salt level in an inspection cell?
The Inspect Cell and Check Salt LED – They flash together when the salt level is 2500-2600 ppm. Your system should continue to produce chlorine and work properly.
How long does it take to hear a click on a pump?
While the pump is operating, move the switch from the “AUTO” to the “OFF” position and back to the “AUTO” position. Wait for about 15 seconds to hear a click in the panel.
Does Hayward Aqua Rite read the correct figure?
Your Hayward Aqua Rite should read the correct figure. If the issue continues, you might need to replace the salt cell.
How to recalibrate Aqua Rite?
Before recalibrating, test the water with salt water test strips to determine the correct salt level. If the results from your test strip are not the same as the Aqua Rite, proceed to step 2. Click Here to View Salt Test Strips.
Can you recalibrate Hayward Aqua Rite?
The Hayward Aqua Rite should now be successfully recalibrated. If the incorrect salt reading continues to be a problem, it may be time to replace the salt cell.
Step 1: Adjusting Salinity (Salt) level
Before the chlorine generator can be calibrated correctly, the salinity—or salt level in the pool water—will need to be at the correct level. For these systems, it should ideally be between 3200-3600 ppm (parts per million). This can be tested using a salt test meter or salt test strips.
Step 2: Locating the Calibration Screen
Once the salinity is adjusted to optimal level, the calibration process can begin. With the pump running and unit set to "Auto" position, press the "Diagnostics" button five times. The screen should display " - 0".
Step 3: Setting the Salinity Level
This step can get tricky and may need to be repeated. While on the calibration screen and with the pool pump still running, push the "Auto" switch down to the "Off" position for two seconds.
More About the Calibration Process
Step 3 takes some practice as it counts down very quickly. For example, if the salinity level in the pool water is 3300 ppm, when the switch is pushed from the "Off" position up to the "Auto" position, after 10 seconds, it will display a set of numbers that start going down immediately. It might start at, say, 4800 (could be higher or lower).
Questions & Answers
Question: My control board shows 3,500, but two independent tests say 2,700 and zero chlorine, and cell tests say it’s good. Which one is correct?
How Does the Aqua Rite Salt System Work?
The Aqua Rite salt system is an easy-to-use salt electrolyzer. It works with Hayward’s TurboCell® technology, which ensures reliable and effective salt treatment. It allows to effectively treat the pool water through saltwater electrolysis.
Why Is My Salt Chlorinator Failing?
Your Aqua Rite chlorinator can produce different results because of so many reasons. One of these is the lack of regular maintenance.
Start By Inspecting the System
Incorrect Aqua Rite readings can occur because of many reasons. Therefore, you have to inspect the system in the following way:
How to Calibrate Aqua Rite System
The steps required for recalibrating the Aqua Rite salt system to ensure accurate reading once again are explained below:
The Problem Is Best Resolved With Maintenance and Calibration
The Hayward Aqua Rite salt chlorinator is designed to read accurate figures. If otherwise, you can reset the Aqua Rite salt system by recalibrating it.
How to recalibrate Aqua Rite?
Before recalibrating, test the water with salt water test strips to determine the correct salt level. If the results from your test strip are not the same as the Aqua Rite, proceed to step 2. Click Here to View Salt Test Strips.
Can you recalibrate Hayward Aqua Rite?
The Hayward Aqua Rite should now be successfully recalibrated. If the incorrect salt reading continues to be a problem, it may be time to replace the salt cell.
Does the Hayward Aqua Rite match the salt level?
WRITTEN BY: Inyo Pools. Occasionally the salt level on the Hayward Aqua Rite may not match the actual salt level of the pool. If the salt cell is clean but the salt reading is off, the Aqua Rite will need to be recalibrated. The following steps will provide a guide on how to recalibrate a Hayward Aqua Rite.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
