How do you load a heavy duty stapler?
- Place stapler on a flat surface.
- Pull the stapler slide mechanism out of the back of the stapler so there is room to insert the staples.
- Insert the staples onto the stapler slide.
- Reinsert the slide mechanism back into the stapler slide.
- Place stapler on a flat surface. ...
- Pull the stapler slide mechanism out of the back of the stapler so there is room to insert the staples.
- Insert the staples onto the stapler slide. ...
- Reinsert the slide mechanism back into the stapler slide.
How to unjam a stapler?
Unjam a heavy-duty staple gun
- Before working on the spale gun, unplug it from a power source as a safety precaution if it’s an electric type and depressurising air if it’s pneumatic.
- Use the screwdriver to dismantle the device. ...
- Using either the screwdriver of the pliers, try to get the staple wire out. ...
How to staple without stapler?
Put down a layer of corrugated cardboard or other protective material. This method involves stapling your booklet against a soft material, then manually pushing the staples down against the booklet. You may use corrugated cardboard, foam, or any other material soft enough for the staples to dig into without attaching.
How do you fix a jammed stapler?
- Firmly carry the handle from the heavy-duty staple remover.
- Take out the rest of the good staple clip and hang it aside.
- Carry the jammed staple using the needle-nosed pliers and pull it.
- Insert the solid clip of staples into the mind from the staple remover.
How to load staples in a stapler?
Part 2 Part 2 of 3: Stapling Paper
- Put the upper left edge of the stack of paper in the stapler’s mouth. ...
- Press down firmly and quickly on the top of the stapler. Then, let go of the stapler’s top, and your papers should be bound.
- Check to make sure that the staple has bound the papers. ...
- Unjam the stapler, if necessary. ...
How do you fill a heavy duty stapler?
0:210:34Swingline Deluxe Heavy Duty Stapler Demo - SWI-39005, SWI-39002YouTubeStart of suggested clipEnd of suggested clipAnd filling is a snap. Simply pull out the lever in the back slide them in and load it back upMoreAnd filling is a snap. Simply pull out the lever in the back slide them in and load it back up that's it that's the deluxe heavy duty stapler by Swingline for more demos reviews.
How do you open the heavy duty stapler?
0:312:11Troubleshooting the Swingline Heavy Duty Stapler - #39005 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey should just slide out the back if they do not however you can load your staples. And smallerMoreThey should just slide out the back if they do not however you can load your staples. And smaller pieces. That way you can open up the front and they'll just pop out.
How do you load a Swingline high capacity heavy duty stapler?
0:190:39Swingline High Capacity Heavy Duty Stapler Demo - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull up the back slide the staples in put the backpack on and you're all set to go that's.MorePull up the back slide the staples in put the backpack on and you're all set to go that's.
How do you take the top off a Swingline stapler?
There's a small button on either the top or bottom edge. Press it to pop out the staple tray. Your stapler may also have a small piece of plastic over the tray that you'll need to remove.
How do you remove staples from a Bostitch heavy duty stapler?
Hold the top of the stapler in place with your non-dominant hand. Never place your hand under the stapler. Use your dominant hand to push in on the back and then pull it up and out. Detach it completely, and the magazine where the staples are placed should be removed as well.
How do you load a Swingline heavy duty stapler 90002?
Loading the staples is simple and straightforward, pull out the back, slide the staplers in, put the back, back on and you're all set to go. That's it, that's Swingline High Capacity Heavy Duty Stapler. For more demos, reviews and how to's, check out MyBinding.com.
How do you refill a Swingline stapler?
0:481:25Swingline® Optima® 40 Sheet Reduced Effort Stapler - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy simply pressing the button on the back of the stapler which ejects the magazine in the front forMoreBy simply pressing the button on the back of the stapler which ejects the magazine in the front for reloading. The compact model opens like a traditional stapler to reload.
How do you open a Swingline stapler flat?
0:271:09Swingline® Optima® 70 Sheet Reduced Effort Stapler - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply push the button on the back of the stapler.MoreSimply push the button on the back of the stapler.
How do you open a stapler?
0:080:43Swingline™ Loading your SmartTouch™ Stapler - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply pull on the top of the stapler. And when it's open loading your staples.MoreSimply pull on the top of the stapler. And when it's open loading your staples.
How do you unjam a Bostitch heavy duty stapler?
How to Unjam a Bostitch StaplerDisconnect the construction stapler from the air supply. Use a hammer and punch to do this. ... Push the driver upwards and past the jammed staple. ... Tap the hammer against the punch and the jam should clear.
How do you open a Swingline stapler flat?
0:271:09Swingline® Optima® 70 Sheet Reduced Effort Stapler - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply push the button on the back of the stapler.MoreSimply push the button on the back of the stapler.
How do you load a Bostitch premium heavy duty stapler?
0:061:22Bostitch® Personal Heavy Duty 60 Sheet Stapler (PHD-60) - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the staples in the magazine. Replace the pusher pushing in until it's locked in place. Now we'MorePlace the staples in the magazine. Replace the pusher pushing in until it's locked in place. Now we're ready to staple. Watch as I staple the 60 sheet.
How to make sure stapler is ready to go?
Clear out any spent staples that remain in the staple tray and make sure the feed line is not jammed with bent staples. Swing the top arm back down as if you want to staple a document. Perform a test staple to make sure your stapler is ready to go.
How to insert staples into a stapler?
Insert your refill staples into the cartridge. Add as many staples as you need to fill the cartridge and slide the cartridge back into the body of the stapler.
How to get stapler to release?
Grasp the top arm of your heavy-duty stapler and pull it up, away from the stapler base. Some types of heavy-duty staplers have a button toward the back of the base that will release this upper arm, while other models simply slide up. As the arm slides up, it exposes the refill tray.
What is a heavy duty stapler?
A heavy-duty stapler makes light work of long office documents, but many office workers don't know how to refill them. Avoid workplace stress by learning how to refill the device so you never have to worry about running out during an important meeting. Heavy-duty staplers come in both electronic and manual formats.
Where is the feed tray on an electronic stapler?
Inspect the exterior of your electronic stapler to find the feed tray, which is typically located toward the back of the electronic stapler. Some electronic staplers have a release button for the feed tray on the back or side of the stapler. Once you have found it, pull the feed tray out with your fingers.
Can you insert more pages than your stapler can handle?
To avoid jams, never insert more pages than your electronic stapler can handle.
How to get stapler back on slide?
Reinsert the slide mechanism back into the stapler slide. Push all the way until flush with the back of the stapler. Push up so hooks on the back of mechanism can grab onto stapler.
How to use a stapler on a flat surface?
Place stapler on a flat surface. Then push in and up on the back side of the stapler until the stapler slide mechanism pops out.
How to get staples out of jammed position?
Jammed? Insert a pen or pointed object into the front slot on the stapler right above the staple exit point. This will push the jammed staples back into position.
How many sheets can you staple with a stapler?
This stapler is designed for stapling up to 240 sheets. It is best to use staple sizes designed for the number of sheets you are stapling regardless of stapler capability. We have enclosed two different staples sizes: one for up to 100 sheets, and another for up to 240 sheets. For best results, use the 100-sheet staples for all projects except those greater than 100 sheets. For projects greater than 100 sheets, use the 240-sheet staples.
Can you staple without staples?
DO NOT staple without staples. When stapling, be sure to slowly apply pressure to the end of the lever arm and push down until the stapling is complete. Quick motions with the lever arm will increase the likelihood of jamming.
How to release staples from a staple gun?
1. Unplug the staple gun and lock the trigger before you begin loading it. Pull the plug out of the wall, and find the trigger lock just behind the trigger that you would use to release a staple. Shift the lock to the left or right, or press it toward the trigger to lock the trigger in place.
How to rear load a staple gun?
To rear load a manual staple gun, start by locating the push rod at the back of the gun. When you're ready to release the push rod, look for a small metal rectangle with 2 indentations on the sides and a small hook on the top or the bottom. Next, push in on the rod, and pull it out to remove it.
What is a staple gun?
Learn more... A staple gun is a handheld machine that can force metal staples or small nail brads into heavy paper, plastic, wood, or thick fabrics. Staple guns come in manual, electric, and pneumatic models to fit a variety of needs, and they’re more powerful than the average desk stapler. Before you can use your staple gun for a woodworking, ...
How to test a stapler gun?
Then, place the front of the gun on a piece of wood pull the trigger to ensure that only 1 staple comes out of the gun at a time. It should fire smoothly with the staple laying flush against the wood.
What is a follower on a staple gun?
The follower is a rod that holds the magazine in place and makes sure it doesn’t move. Most pneumatic staple guns have a large one at the front of the gun, protruding from underneath the area where the staples fire out of the gun.
How to make sure staples are loaded?
To make sure the staples are loaded properly, fold a piece of paper in half or use a scrap piece of wood or fabric. Place it under or inside of the stapler and pull the trigger to release a staple. Make sure the staples are firing smoothly with no jams.
How to release a pusher rod?
1. Locate the pusher rod at the back of the gun. Point the gun so that the area where the nails come out of is facing away from you. Then, look at the back of the gun for a small metal rectangle with 2 indentations on the sides and a small hook at the top or bottom. This is the release for the pusher rod.
What to do if staples are left in stapler?
If there are any staples remaining in the stapler, throw them away.
How to open stapler?
1. Open up the standard or mini stapler. On most staplers, you lift the top. There may be some latches on the side that need to slide to unlock it. In some cases, the stapler doesn't open upward; instead, a large push button on the top rear ejects the tray out the front. Examine the stapler you're refilling to work out which method will open ...
How to check if stapler is working?
Check that the stapler operates correctly by doing a test staple. Place a small stack (2-3 pages) of scrap papers between the magazine and the staple base. If it works, you've added the staples correctly. If your staples emerge bent, or they remain stuck inside your stapler, you’ll need to reopen the stapler.
How to tell if stapler is closed?
If you’re not sure whether or not your stapler is completely closed, check and see if a staple is released when you press the magazine to the base.
What are the different types of staplers?
There are three main types of stapler: the standard, mini and staple gun. In addition, many printers and copiers also contain stapler cartridges. To refill your stapler, you’ll want to start by making sure you’re matching the new staples to your stapler. After identifying the correct staples, you’re ready to load your stapler.
How are staples held together?
Staples are held together gently in a stick or row by force or glue. This is to make their addition much easier. You may need tweezers to remove fresh staples from the stapler package if you find it hard to get your fingers in. If you have partial rows, you may add these as long as they slide into place easily.
What is the difference between a staple gun and a fine wire stapler?
Medium and heavy wire staple guns generally load from the top, while most fine wire staplers are bottom load.
How to load a stapler?
Step 1: As spring-powered staplers are bottom loading, you need to first flip the unit upside down so the base is facing up. Open it up as you would a standard stapler, pulling the base away from the top handle. Step 2: Slide the magazine out by pulling back the black tab shown below. Step 3: Now is the moment you've been waiting for!
What is spring powered stapler?
Spring-powered staplers are different than standard staplers, how you ask? Well, they boast One-Finger™ technology by PaperPro® for effortless stapling that's 80% easier! Whether you're using a heavy duty, compact or long reach unit, you can now breathe easy; there's no more exuding all your force to squeeze this stapler!
