- Disconnect the spark plug wire Pull the spark plug wire straight up and off the plug.
- Remove the belt cover Using a socket and ratchet, remove the bolt that fastens the belt cover to the frame of the snowblower. Detach the belt cover. ...
- Remove the belt Pull the auger belt off of the engine pulley. PHOTO: Remove the auger belt.
- Remove the frame panel Tip the snowblower forward so it rests on the auger housing. Remove screws that secure the frame panel located between the wheels. ...
- Remove the belt keeper Loosen the hex nut and remove the belt keeper. PHOTO: Remove the belt keeper.
- Remove the belt Note the routing of the belt before removing it. Depress the drive engagement lever with a spring clamp or have a helper hold it closed. ...
- Install the new belt Insert the new belt on the auger pulley. ...
- Reinstall the frame panel. Reinstall the frame panel. Pivot the snowblower upright so it rests on its tires.
- Install the belt on the engine pulley Position the belt on the engine pulley and roll it in place. Reinstall the belt cover.
- Test the snowblower Reconnect the spark plug wire. Fill the tank with gas and test the snowblower.
How do you change the belt on a snowblower?
Most snowblowers require you to "split" the scoop from the tractor to make room to slip the belt between the pullies. Remove the top bolts from both sides and just loosen the lower bolts to allow it to pivot. You will need a way to hold up the handlebars so they do not come crashing down to the floor.
How do you fix a snowblower that won’t spin?
Replace the auger belt if the snowblower won’t throw snow because the belt broke and won’t spin the auger. Also replace it if the auger drive belt is so worn that it slips or squeals when you use the snowblower. Use the manufacturer-approved snowblower part to replace the auger belt.
How do you attach an auger belt to a snowblower?
Insert the auger belt over the auger pulley and the remaining ribbon thread toward the top of the snowblower. Stretch the frame spring back to the other side of the frame, and hook the spring in place. Install the clamp bolt that serves as the strap fixator.
How do you remove the cover from a snowblower?
The snowblower wheels will be off the ground. Remove the bolts holding the lower frame cover to the snowblower with a socket wrench. Remove the cover from the snowblower. Step 5: Find the screw that serves as a clamp strap around the auger pulley.
How do you change a belt on a snowblower auger?
1:484:10How to Replace a Snowblower Auger Belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a clamp to hold the drive lever to the handlebar. Remove the old belt from around the augerMoreUse a clamp to hold the drive lever to the handlebar. Remove the old belt from around the auger pulley and slip the belt between the support bracket and the auger pulley.
How do I change the drive belt on my MTD snowblower?
2:409:25Snowblower Drive Belt Replacement - MTD/CUB CADET ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe auger belt forward slide the new drive belt over here. And now what you need to do is push theMoreThe auger belt forward slide the new drive belt over here. And now what you need to do is push the drive belt behind the pulley over here toward the engine. And between the body of the snowblower.
Are all snowblower auger belts the same?
All snowblowers have at least one belt, whether you have a gas powered version or electric, and the directions are generally the same for all models with very little variation.
How do you change a drive belt on a Craftsman snowblower?
1:538:41How To Change Drive Belt on Craftsman 24'' SnowblowerYouTubeStart of suggested clipEnd of suggested clipIt down in behind this pulley. Just do whatever you got to do and it goes under the back one here.MoreIt down in behind this pulley. Just do whatever you got to do and it goes under the back one here. It goes on the far back one the auger belt goes up here and it's a different style of bill.
How do I know if my snowblower auger belt is bad?
0:463:00HOW TO Check The Belts On Your Snowblower - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow a good way to see these belts are good is to hold down the lever. For the auger control up hereMoreNow a good way to see these belts are good is to hold down the lever. For the auger control up here on your handle.
How do you tighten a MTD snowblower auger belt?
1:103:01HOW-TO - Snowblower Auger Belt Adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo in this case what I need to do is loosen the bolt that holds the pulley. And move the pulleyMoreSo in this case what I need to do is loosen the bolt that holds the pulley. And move the pulley forward. Then once the auger lever is engage the belt will be tighter.
How long does a belt last on a snowblower?
Snowblower belts start to wear out after 5 to 7 years, and should be replaced. You can save money by doing the job yourself.
What size belt does a Craftsman snowblower take?
Exact size auger belt fits Craftsman snowblower 37X120MA, 581264MA 1/2" X 35.6"
How do you change a drive belt on a Toro snowblower?
0:232:26How To: Replacing the Drive Belt on your Toro Snowblower (Single Stage)YouTubeStart of suggested clipEnd of suggested clipWhich should be positioned just above the rotor shaft reinstall the rotor pulley on the shaft. AndMoreWhich should be positioned just above the rotor shaft reinstall the rotor pulley on the shaft. And secure it with the curved washer and screw reattach the brake spring to the idler arm.
How many belts are on a snowblower?
For most two stage snow blowers, there are 2 or 3 belts under the cover. One belt will drive the auger, and the other will drive the wheels. Looking at the belts, what do you see? If you see excessive cracking, fraying or splitting, it's time to replace the belts.
What does the drive belt do on a snowblower?
For dual-stage models, the drive belt or belts will turn the auger blades to cut through the snow and throw it towards the impeller which the belt rotates so the snow will be propelled through the chute.
When should I change my snowblower belt?
Snowblower belts start to wear out after 5 to 7 years, and should be replaced. You can save money by doing the job yourself.
How do you tighten the belt on a yard machine snowblower?
2:204:56HOW TO REPLACE THE BELT on Yard Machines Single ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust. Pull over the motor with the cord. Again watch out your fingers don't get caught between theMoreJust. Pull over the motor with the cord. Again watch out your fingers don't get caught between the belt and the pulley. So I'm just going to push lightly like this now.
What is the belt on a snowblower?
The auger belt is the most important belt on the snowblower. This controls the amount of electricity that comes through the fan hoses.
How long does it take to change a snowblower belt?
Fortunately, if you have a spare belt handy, changing the belt doesn’t take more than 10 minutes. If you have a replacement socket wrench and a couple of belts, you are more than ready to change your snowblower belt.
How do you know when you need to replace a belt?
When this happens, the snow thrower will stop firing the snow from the falling fan. A snowblower belt will wear out after five to seven years and will need replacement.
How does a snowblower drive belt work?
Snowblower drive belts are designed to transmit rotational motion from the driveshaft to the drive. In snowblowers, there are 2 types of belts. The first belt connects the auger shaft to the drive shaft and the second transmits rotational motion to the wheels. In cases where the unit refuses to drive, there can be 2 reasons: wear of the friction ring and breakage of the drive belt. If the friction is correct, then repairing the fault means changing the transmission belt. The drive belt is replaced in the same way as the auger belt. Once the worm gear mechanism has been disconnected, it is necessary to remove the cover that hides the drive pulley (indicated by an arrow). In this section, we’ll see tips on how to maintain the snowblower belt and also the snowblower in general.
How to tell if auger belt needs adjustment?
You can tell the auger belt needs adjustment or replacement when the control cable is properly adjusted , but the snow does not trigger. You have to replace the belts instead of adjusting them when there is visible damage.
How to stop snowblower from spilling fuel?
Step 1: Siphon fuel from the snowblower fuel tank in a gas canister with a handheld siphon. The snowblower requires tilting. Siphoning the fuel line will prevent it from spilling. Disconnect the spark plug wire from the spark plug.
What happens if a snow thrower doesn't move forward?
If the snow thrower will not move forward, the belt needs the track for adjustment or replacement. So, you will need to know how to change a snowblower belt.
What to do if your snowblower is damaged?
Replace the 4-way chute control assembly on your snowblower if it’s damaged.
How to remove a belt from an auger?
Note the routing of the belt before removing it. Depress the drive engagement lever with a spring clamp or have a helper hold it closed. Remove the belt from the auger pulley. Rotate the belt 90 degrees so that it slides over the pul ley bolt and pull it out.
Why won't my snowblower throw snow?
Replace the auger belt if the snowblower won’t throw snow because the belt broke and won’t spin the auger. Also replace it if the auger drive belt is so worn that it slips or squeals when you use the snowblower. Use the manufacturer-approved snowblower part to replace the auger belt.
What to do if your snowblower isn't getting fuel?
Rebuild the carburetor on your snowblower if the engine isn't getting fuel.
Where to insert belt on auger?
Insert the new belt on the auger pulley. Check that the belt is fully inserted in the pulley groove and not on the outside of the break tab or belt keeper.
When to replace fuel filter on snowblower?
Replace the fuel filter on your snowblower if it's clogged or damaged.
