Disassembling the Throttle Control
- Step 1: Removing High Idle Mode Button First, we want to remove the shifter from the boat. ...
- Step 2: Removing Shifter Nut Up next is one of the most difficult parts. ...
- Step 3: Undoing Center Section ...
- Step 4: Removing the Throttle Linkage ...
- Step 5: Removing the Neutral Safety Switch ...
- Step 6: Removing the Shifter
Full Answer
How do you remove an outboard throttle cable?
Pull the throttle pin out of the cable. Remove the throttle cable retaining clip. Pry the cable trunnion out of the steering handle and remove cable.
Why do some boats have two throttle controls?
Dual-function mechanical controls are the most popular type of control in use today because they make boat handling easy. Both shift and throttle are operated by a single lever in a very instinctive action. Shifting is quick and can only be done at low rpm, which protects the engine's shift mechanism.
How does a boat throttle control work?
1:429:27Boat throttle controls - how they work. Using a boat shifter - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is essentially your accelerator pedal. And also your transmission shifter any point forward ofMoreThis is essentially your accelerator pedal. And also your transmission shifter any point forward of the locking neutral. Position is for momentum. So if you want to go forward slowly.
What is throttle only button on boat?
0:041:41Joystick Piloting: Throttle Only Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm gonna talk to you about a feature on your remote control called throttle only throttle only is aMoreI'm gonna talk to you about a feature on your remote control called throttle only throttle only is a feature that disables the shift function on your remote control handles.
What are the two levers on a boat throttle?
Two-lever Throttle This lever controls your speed. Push the left lever forward to shift into forward gear, or pull it back to shift into reverse gear. Always bring the engine to an idle before shifting gears. Use the right lever to control your speed.
What are the 2 levers on a boat?
Seems I can remember a boat my dad had with two levers. Yes, it was gearing. The smaller lever switched between forward and reverse. The larger was for throttle.
What does up and down mean on a boat throttle?
Just remember that the boat's bow will move in the same direction you press the trim button—button up is bow up, button down is bow down. Learn More: How to Drive Boat.
How do you adjust a boat throttle?
Start the engine and, with the engine running, twist the throttle grip. Twist it counterclockwise from the "Idle" position to increase speed and clockwise to decrease speed. If there's a throttle lever rather than a throttle grip on the tiller, move the lever in increments to increase or decrease throttle.
Can you steer a boat in neutral?
Shifting into neutral subtracts prop wash, but the boat's headway through the water allows the drive or rudder to keep working, so some steering control is retained. The same holds true in reverse gear (sternway). The faster the boat moves through the water, the greater the steering force of rudder effect.
How do I make my boat throttle smoother?
2:598:29Boat Throttle Shifter Cable Lubrication made easy - YouTubeYouTubeStart of suggested clipEnd of suggested clipOil down in there i'll fill this funnel up just a little bit. That's enough for now. And then downMoreOil down in there i'll fill this funnel up just a little bit. That's enough for now. And then down here on the engine. I'm gonna move the throttle cable back and forth.
What is the throttle friction screw?
A pilot-operated device to stiffen the movement of the throttle lever(s) so as to effectively lock it in the set position and prevent it from slipping back to any selected setting.
What does a neutral throttle lever do?
Yes! Neutral throttle happens between braking and accelerating and is defined as opening just enough throttle to hold our radius at our given lean angle.
How do you steer a boat with a throttle?
Engage forward (or reverse if you need to back out of a slip) by pushing the throttle handle forward (or pulling it back) gently until you feel it shift into gear. When the boat begins moving, spin the wheel just as you would turn the steering wheel in a car to determine direction of travel.
How do you start a boat throttle?
0:441:44Sea-Doo - BOAT SHIFT/THROTTLE LEVER OPERATION - YouTubeYouTubeStart of suggested clipEnd of suggested clipControl is the throttle lever. To start the engines the shifter must be in the neutral. Position andMoreControl is the throttle lever. To start the engines the shifter must be in the neutral. Position and the throttle must be pulled back to the idle.
How do I make my boat throttle smoother?
2:598:29Boat Throttle Shifter Cable Lubrication made easy - YouTubeYouTubeStart of suggested clipEnd of suggested clipOil down in there i'll fill this funnel up just a little bit. That's enough for now. And then downMoreOil down in there i'll fill this funnel up just a little bit. That's enough for now. And then down here on the engine. I'm gonna move the throttle cable back and forth.
What does the Transfer button do on Mercury throttle?
Transfer Button allows control to be easily transferred from one helm to another. Neutral Indicator Light shows when the engine is not in gear.
Replace that old throttle control box and don't go broke!
Replacing that ugly, worn out, and sloppy control box doesn't have to be expensive, and the feeling will be like night and day. If you search the web for throttle and shift control boxes you'll find that there are numerous options out there. Top mount, side mount, dual lever, single lever...
In With the New Control Box
Maybe you are going with a high-quality retro-looking twin lever control box with one lever controlling the FWD / NEUTRAL / REV (forward, neutral, reverse) and the other lever controlling the engine speed like this one.
Control Cables
If you’re already going to change your controls, it's prudent to replace your old control cables, too. Remember, your cables are as tired as the control unit is, so now is the right time to update the whole system.
