- Turn off water at mains.
- Remove handle by removing indicator button.
- Use an allen key to unscrew the grub screw.
- Unscrew dome cover and locking nut.
- Replace cartridge.
- Re-assemble tap.
- Turn on water supply and inspect for leaks.
Full Answer
How to replace a cartridge in a mixer tap?
Replacing a Cartridge in a Mixer Tap 1. Stop the water flow to the tap using the isolating valves usually located under the sink. You complete this by... 2. Remove the decorative cover on top of the tap handle. You can use your nail to do this or a blade being careful not... 3. Using an Allen Key ...
Can you take the headgear off of a mixer tap?
It’s a mono block mixer tap in the kitchen. I can take the headgear off no problem but the cartridge is recessed inside the tap housing - can’t a spanner to it, and it doesn’t look like there’s enough clearance between the cartridge and inner wall of the tap housing to fit a socket wrench.
How do I clean the cartridge?
Now that we have the cartridge out it is a good idea to clean the inside of the chamber with soapy water and a cloth to remove any debris or limescale build up. You can grease the O rings here with a non corrosive grease if necessary and also grease the retaining nut if necessary.
How do I install the cartridge to the mixing chamber?
Make sure that the two cartridge lugs match the mating holes in the tap mixing chamber above. You will feel it click into place and the top of the cartridge will be flat. Do not screw the retaining nut back in on a cartridge that is not seated correctly. If you do, then you will damage the cartridge and also cross thread the retaining nut.
How do you remove a cartridge from a mixer?
0:391:52bathstore: How to change the cartridge in a mixer tap - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd insert the new cartridge by locating the two plastic pegs on the back of the cartridge into theMoreAnd insert the new cartridge by locating the two plastic pegs on the back of the cartridge into the seating of the tap body once the new cartridge is in place replace.
How do you disassemble a mixer tap?
3:3414:51How to repair a Mixer Tap / Faucet, Pull the cartridge apart and lube it ...YouTubeStart of suggested clipEnd of suggested clipBut you will need to turn the water off before you go any further otherwise you'll have a fountainMoreBut you will need to turn the water off before you go any further otherwise you'll have a fountain running in the middle of your sink. So set this down again and we'll pull this apart.
How do you remove a tap head from a mixer?
0:3317:25How to remove different type tap handles in order to repair the tap.YouTubeStart of suggested clipEnd of suggested clipOkay there's a screwdriver. There's our head dangle pin this one off for you sure I used to do crackMoreOkay there's a screwdriver. There's our head dangle pin this one off for you sure I used to do crack this one yet. This.
How do you remove the cartridge from a tap removal tool?
1:044:29FRANKE ASCONA - How to replace the tap cartridges, repair ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI will use a pair of grips. And then pull towards you so that the tail is turning anti-clockwiseMoreI will use a pair of grips. And then pull towards you so that the tail is turning anti-clockwise that will release the valve continue unspinning have a bit water. Here. We have got the valve removed.
Why is my mixer tap dripping?
A damaged or loosened tap washer is likely to be the reason you have a dripping tap. All you need to do to replace it is unscrew or slide off the original washer and screw or slide on a new one. Make sure it is tight and an exact fit for your tap.
How do you remove a mixer tap spout?
0:004:32Mixer tap spout splaying water everywhere? - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe spout often you get that kind of Jets to one side so can I have a look at that today I'm goingMoreThe spout often you get that kind of Jets to one side so can I have a look at that today I'm going to show you one now just doing exactly that and the fix for it.
How do you remove a tap head with no screws?
0:055:19How to remove a Tap with NO Screw the Secret Tool! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff there's no screw to remove from the spindle. Well there is quite a few videos on youtube thatMoreOff there's no screw to remove from the spindle. Well there is quite a few videos on youtube that you can shoot with this make sure your water's off of course open your tap up on all the way.
How do you change a washer on a mixer tap?
1:355:01How to Fix a Kitchen Tap with Wickes - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing an adjustable spanner unscrew the valve and remove. Use a screwdriver to remove the washer andMoreUsing an adjustable spanner unscrew the valve and remove. Use a screwdriver to remove the washer and replace. Finally screw back in the valve. And tap handle.
How do you remove round tap heads?
How to Remove a Tap Head. To remove the tap head, simply prise off the tap indicator cover and remove the retaining screw beneath it. Once the screw is removed the tap head should then pull off. Occasionally, once the retaining screw has been removed the head of the tap will still not come off.
How do you remove bathroom tap cartridges?
You'll likely need to remove a bonnet nut or retaining nut. Unscrew the nut with an adjustable wrench. The plastic cylinder with a stem on top is the faucet cartridge....Remove the HandlesUse a screwdriver to remove each screw. ... Set the screw aside. ... Carefully pull straight up on the handle. ... Repeat for the other handle.
Are all mixer tap valves the same?
These parts are not standard between manufacturers either so you will need to check the sizes carefully to ensure they are exactly the same. This is also sometimes the only option for customers with very unusual or rare sized tap valves.
How do you remove a ceramic tap cartridge?
4:1910:33How to Replace Ceramic Cartridge - Dripping Tap Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo let's have a go in there they'd have a small screwdriver. It does the job. Take that off and nowMoreSo let's have a go in there they'd have a small screwdriver. It does the job. Take that off and now the next tricky bit is we've got to get into there to undo. The inside of the tap.
Types of Cermaic Cartridge Valve
There are two main types of Cermaic Disc Cartridge: 1. Ceramic Disc Cartridge for flow control only. 2. Ceramic Disc Cartridge for flow and temperature control. This post will focus on the temperature and flow type as shown below.
Removing and Replacing the Cartridge
We recommend you always use a plumber for these jobs if you do not think it is something you feel comfortable with. It is quite straight forward though and should take in the region of 20 to 30 mins. Tools Required: Screw Driver, adjustable spanner, Allan Keys. grease if necessary and potentially a blade like a Stanley Knife. 1.
And Finally.
10. To finish, reopen the isolating valves slowly and check for leaks. That’s it, the tap should now operate correctly! Hope this helped. You can find mixer taps in our shop: www. thetapshop.ie
