Push the hooked end down the drain and into the piping as far as you can. Afterward, twist it and pull it upward. Repeat the above process until you pull something out. If your drain has a basket strainer—the screen designed to catch foreign particles—remove it from below the sink with an adjustable wrench.
How do you remove a kitchen sink drain?
To remove a kitchen sink drain, all you’ll need is a wrench, a screwdriver, and a pair of needle-nosed pliers. The first thing to do is loosen the coupling nut connecting the strainer to the drain pipe, which you can usually do by hand. If the nut is very tight, hold the strainer in place from above with the pliers while you loosen it.
How do you remove a stuck drain pipe nut?
Wrap a towel around the nut to help you get a better grip on it. A metal nut may also require the use of a pipe wrench or large adjustable wrench. If you wish, you may also be able to disconnect the drain pipe at the top of the trap (the U-shaped bend) in order to give yourself more room to work with.
How do you remove a sink strainer from a PVC pipe?
Loosen the coupling nut that connects the strainer to the drain pipe. Sink strainers are always made of metal, but most modern homes have white PVC drain pipes. You’ll find either a PVC or metal coupling nut connecting these two components beneath your sink. Loosen this nut to separate them. [1]
How do you remove a bell washer from a drain pipe?
Loosen and remove the nut at the bottom of a bell washer strainer. Take the same wrench you used to loosen the nut that held the strainer to the drain pipe, and loosen the same-sized nut that pushes up against the bell-shaped housing. Work the nut off the threads and out of the way, and then pull the bell housing down and off of the strainer. [8]
How to get a bell housing off a sink?
Where to place washers and gaskets on a sink strainer?
How to tighten a locknut on a sink?
How to remove a locknut strainer?
How to immobilize a sink strainer?
How to get a stubborn nut out of a strainer?
What to do if strainer won't break free?
See 4 more
About this website
How do you disconnect a drain pipe?
0:101:35How to Remove the P-Trap Without a Plumbing Wrench - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing your rag place it in your hand and grip the p-trap. Now grip the other side and you're doingMoreUsing your rag place it in your hand and grip the p-trap. Now grip the other side and you're doing this so you don't actually snap the pipe. And just turn it loosen up a little bit now do the other.
How do you remove a drain pipe from a wall?
Cut the PVC pipe at any point inside the wall that allows you to remove the stub-out, using a hacksaw. You may have to make two cuts to separate the tee holding the stub-out from the waste and vent pipes. Remove any clamps holding the stub-out with a screwdriver or hammer, and pull out the stub-out.
How do you remove drain pipe from concrete?
Ways to clear concrete from drainsFlush. If the cement has accidentally (and recently) been put into a drain flushing it with plenty of water may be a simple but effective fix. ... CCTV inspection and high-pressure jet blasting. ... Mechanical tools. ... Biodegradable, cement-softening products. ... Acid.
How do you remove a drain trap?
Disassemble The Drain Trap First, locate the drain trap. Then, unscrew the slip joint nuts found on each side of the “j” bend of the trap. Loosening these will remove the trap from the sink tailpiece and the neighboring wall fitting. If you have a newer sink, unscrewing the drain tap can be done by hand.
How do I remove an old drain assembly?
0:233:05Plumbing Advice : How to Remove a Sink Drain Assembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your pliers loosen the locknut from the bottom. That may take a minute sometimes they're aMoreTake your pliers loosen the locknut from the bottom. That may take a minute sometimes they're a little bit rusty. Once you get that removed. You'll want to work the drain assembly. Up.
How do you remove glued PVC pipe?
1:593:22How To Remove Glued PVC Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's also important to use a steel hole soft sand steel holds the heat very well. Okay after theMoreThere's also important to use a steel hole soft sand steel holds the heat very well. Okay after the time is up remove the hole saw. And use some needle nose pliers to pull out the softened pipe.
How do you remove metal pipes from concrete?
Dig a hole, cut the steel with whatever tools you have (hacksaw, grinder, sawzall) hit the top with a hammer and it will snap easily. If you happen to have a large pipe cutter for steel pipe you can use that, but odds are you don't.
What will dissolve concrete?
Concrete is a durable building material that takes special materials to dissolve once it's hardened into place. Phosphoric acid and trisodium phosphate are the main compounds used to dissolve concrete leftover from masonry work.
How do you soften hardened concrete?
Water is the most common way of softening concrete and is usually enough by itself to break down older materials. However, water alone may not be sufficient to break down concrete that has hardened over time. Adding other substances such as glycerin or alcohol helps loosen up the mixture.
How do you replace a sink drain pipe?
0:151:52How to Replace a Sink Trap | Plumbing | The Home DepotYouTubeStart of suggested clipEnd of suggested clipTo do this first attach the fitting with slip washers and nuts. Then apply pipe lubricant on theMoreTo do this first attach the fitting with slip washers and nuts. Then apply pipe lubricant on the slip washer to ensure a tighter. Fit. Now it's time to attach the trap arm to the drain stub.
How do you unscrew a pipe without a wrench?
What to Use if You Don't Have a WrenchDuck tape. Duct tape is useful in almost any situation but you may be surprised to learn that you can use it to loosen bolts. ... Two coins. Who would think that money can be used as a makeshift tool? ... Zip-tie. ... Another nut and bolt.
Where is the drain trap?
Also known as a “P-trap,” a sink trap is a curved length of pipe located below the drain. If you follow the drain pipe from the bottom of the drain to the wall, this bend should be relatively in the middle, underneath the sink.
How do you remove a metal drain pipe from a wall?
0:023:32How to Repair Cast Iron Drain Pipe In The Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i cut it using my milwaukee m18 fuel sawzall. And the milwaukee torch carbide blade which isMoreAnd i cut it using my milwaukee m18 fuel sawzall. And the milwaukee torch carbide blade which is designed for cutting cast. Iron. Next i just wiggled the cast iron pipe out of the wall.
How do you remove a P trap from the wall?
To remove the P-trap from the wall stub, hold the trap assembly firm with one hand and turn the coupling nut counterclockwise with respect to the wall stub until it comes loose. If the nut is overtightened or old, you might have to use a wrench or a pair of pliers for the purpose.
11 Easy Steps How to Remove Kitchen Sink Drain - In the World of Design
Stop Water Supply The sink cabinet or box contains hydrants, which open or shut the water supply to pipes. Turn them then open the faucet to check, if the water is not flowing you may start work removing the kitchen sink drain.
How to get a bell housing off a sink?
If the bell housing refuses to pull free easily, wedge a flat head screwdriver into the gasket sandwiched between the bell and the underside of the sink. Pry the bell housing free and pop it off.
Where to place washers and gaskets on a sink strainer?
Place any included washers and gaskets between the underside of the sink and the locknut or bell housing. A metal-to-metal connection between the sink bottom and the locknut or bell housing won't be watertight. The new sink strainer will come with at least one rubber gasket, and possibly other gaskets or washers made of rubber, cardboard (to protect the rubber), or other materials. Place them as directed in the product instructions before tightening the locknut or bell housing.
How to tighten a locknut on a sink?
Secure the sink strainer into place from below. For a traditional locknut strainer, use a large pipe wrench or strainer locknut wrench to tighten the locknut (by turning it clockwise). Securely press the strainer against the underside of the sink, but don’t feel like you have to tighten it so much that the parts seem ready to fuse together.
How to remove a locknut strainer?
If you also see 3 or 4 screwheads against the locknut, you need to remove these screws before loosening and removing the locknut and strainer. A simple screwdriver (typically Phillips head) will do.
How to immobilize a sink strainer?
If you have trouble squeezing the pliers, you can also insert the handles of the pliers into the openings of the strainer grate, then stick a screwdriver between the handles and hold it steady to immobilize the sink strainer.
How to get a stubborn nut out of a strainer?
If the strainer is spinning counterclockwise along with the nut as you loosen it, you’ll need to hold it still from above. Insert a pair of needle-nose pliers or a sink drain wrench down into the sink and pinch the strainer grate (not the removable strainer basket) to immobilize the entire strainer.
What to do if strainer won't break free?
If the strainer won’t break free, tap it from the underside with a mallet until it pops loose. If you have to bash too hard, though, you may damage the sink itself, so consider calling a plumber if necessary.
How to get water out of a P trap?
Set a bowl under the "P" trap to catch the water that is trapped in it. Loosen the nut just enough to know it is loose. Then locate the nut on the back of the "P" trap. Loosen it all the way and gently pull down on the "P" trap to remove it from the tailpiece. Clean up any water that might have spilled onto the bottom shelf ...
Where is the nut on a kitchen sink?
Locate the nut on the underside of and right next to the sink bowl. Reach in with your hand to get an idea of what you are working with. Be certain that you remove any debris around the area to avoid getting it in your eyes if you have to place your head inside the cabinet. Advertisement.
Can you remove a P trap without gloves?
Do not remove the "P" trap without rubber gloves if the sink drain has recently been unstopped with a chemical drain cleaner. Do not allow debris to fall into the "P" trap when reinstalling it.
Can you cut a drain pipe nut off?
Back the nut off slowly, as it can get cross-threaded and become very difficult to remove. If this occurs, the nut or the drainpipe will have to be cut off. This is generally accomplished with a hacksaw.
What to do if your drain is blocked?
If the item you're looking for isn't there, and the drain is still blocked, don't despair, because there's still something you can do. Unscrew the trap arm from the waste inlet and look inside the arm, then probe the waste pipes with a piece of wire or a zip-it tool and try to hook onto it and extract it.
How to get stuck items out of sink drain?
All you have to do is disassemble the P-trap. This procedure is simple, and you can usually do it by hand, but you may need a pair of adjustable pliers. Unscrew the compression nut ...
How to get rid of water in a trap?
Do this carefully, because it's full of water. Invert the trap over a bucket and out will come all the water along with all your valuables that have collected in the bottom. If the item you're looking for isn't there, and the drain is still blocked, don't despair, because there's still something you can do.
How to remove a P trap?
First, you have to remove the stopper or the strainer, and while the procedure depends on the stopper mechanism, they are all removable. Try hooking onto the item with a zip-it tool or , if it's metal, latching onto it with a magnet. Vacuum all the water out of the P-trap as a last resort, and once you remove the obstruction, remember to run the water to refill the trap after you replace the stopper or strainer.
What is the easiest drain to get stuck in?
Of all the drains in your house, the sink drain is the easiest from which to retrieve a stuck item. The sink gets used a lot, so its drain is the one in which stuff is most likely to get stuck. The shower drain and some bathtub drains have strainers that prevent all but the smallest debris from getting in.
What to do when you get stuck in a toilet?
When something is stuck in the toilet P-trap, you can try putting on gloves and reaching into the P-trap to get it . If you don't have any luck, use a toilet auger. As a last resort, take the toilet off, turn it over and reach in from the other side. Advertisement.
What to do if you can't dislodge a vacuum?
If you can't dislodge it, fit the hose of a wet/dry vacuum over the waste opening, seal the connection with tape and turn on the vacuum. You'll probably get a lot of gunk, but you should also get what you're looking for. Advertisement.
Where is the drain pipe on a washer?
The drain pipe is usually found at the bottom of the machine, underneath the barrel.
What to do if your washer is full of water?
If you find your washer full of water even though the cycle has ended, you may need to replace the washing machine drain hose. Before you can put on the new one, you have to remove the old one. This is neither a complicated nor overly delicate task, so even beginners should not be afraid to dip a toe into the world of do-it-yourself repairs.
Why is my washing machine running out of water?
You might also hear the washing machine finish running through its cycle only to find that your clean clothes are sitting in a washer full of water because it did not drain.
How to remove a clogged downpipe?
Remember that sometimes the downspout is clogged, not the downpipe. Look down the spout with a flashlight before removing it to see if there is a blockage in there. If so, spray down with a high-pressure hose to dislodge it.
What is a downpipe drain?
Learn more... A downpipe drain is the underground pipe that runs water from gutters away from a building and usually lets out at the curb. Over time, leaves, dirt, and other debris can clog up the pipe. If your downpipe isn’t draining or water is flowing out the back, then it’s probably clogged. First, try to dislodge it by feeding a hose into ...
How to unclog a clogged drain with a snake?
Once you think you’ve broken up the clog, leave the snake in the drain and go get your hose. Spray it down into the pipe and see if water comes out the other side. If it does, then you successfully unclogged the pipe. If not, continue working the snake further to find other blockages.
How long should you leave a snake in a clogged drain?
Leave the snake in until after you check that the clog is dislodged so you don't have to re-insert it.
What is a plumbing snake?
If the water wasn’t strong enough to dislodge the blockage, you’ll have to remove the clog manually. A plumbing snake is a tool that plumbers use to clear drains. It has a wire string that you can lower down a drain and a spool that spins it to dislodge clogs.
What to do if your hose is too short?
If your hose is too short, you can get an extender. Otherwise, just start spraying the water when the hose reaches its max length.
How big is a standard plumbing snake?
Standard plumbing snakes are 50 feet (15 m). This should be enough for most downpipe drains, but if yours is longer, get a larger snake.
What tools do drain cleaners use?
Professional drain cleaners have the most powerful equipment for this and are experienced in using the tools to achieve optimum results. 3. Mechanical tools. Again, use of mechanical tools such as augers (or plumbing snakes) is usually best left to professional drain cleaners or those who have experience or training.
What to do if concrete is too hard?
After that, you should arrange for a cleanout with a high-pressure jet blaster.
Can acid be used to clear a clogged pipe?
Acid is no miracle fix. Chemicals will only work on the surface of the blockage. This means for large blockages you’ll have to keep pouring it in, letting it stand, clearing the softened mass (perhaps even scooping it out if it is near the entry) and then starting again from scratch. If you don’t use a biodegradable acid you can damage your pipes and the environment, particularly if you try to speed up the process with a stronger concentration than recommended (not advised). A too-strong concentration can also transform the blockage into a large clog which itself is hard to move, and slows the overall rate of dissolution.
Can you put concrete down a shower drain?
Getting concrete down drains is not only very simple but remarkably common. Regularly washing cement or other building compounds from tools, clothes and bodies into household plumbing fixtures is obviously a convenient way to go. But when you find yourself standing in a puddle of murky water because the buildup of concrete in the shower drain has blocked the pipe, you’ll wish you’d made the effort to wash off outside.
Can you flush cement in a drain?
If the cement has accidentally (and recently) been put into a drain flushing it with plenty of water may be a simple but effective fix. Count your lucky stars if it works, and you will only really be moving the cement products to another section of the overall pipe network, but hopefully, it will remain saturated enough to not form into a hard mass.
Can you get a bit of cement dust down the drain?
Many home renovators and professional tradespeople seem to think no harm will come from a bit of cement dust or tiler’s grout being washed down the drain. And most likely there won’t. Not that night. But over time build-ups can occur and the property owner will have a very difficult problem to rectify. One common problem is when new floors are being laid in wet areas and a self-leveler is used. Excess materials are often ‘accidentally’ dropped into the floor or shower grates and cause pipe blockages over time.
Can drains be blocked with concrete?
When drain clearing is not enough. Sometimes drains blocked with concrete are so clogged even professional clearing fails. Build-ups of concrete or other building materials can also put so much pressure on pipes, cracks or ruptures occur.
Why does my bathroom drain smell so bad?
This is probably one of the most common irritations in households: a foul odor from the drain in your bathroom or kitchen. You have cleaned everything nicely, everything shines, but a foul odor keeps coming out of the drain. This odor is caused by mold, because food scraps always remain in the drain. Especially when it is hot or raining heavily outside, the drain can quickly emit an unpleasant odor.
Is air freshener bad for drains?
There are a huge number of chemical products on the market that can remove this odor from your drain, but these products are often extremely harmful to your health and the environment. An air freshener is an option, but this does not address the problem at its core. It only deals with the symptom.
How to get a bell housing off a sink?
If the bell housing refuses to pull free easily, wedge a flat head screwdriver into the gasket sandwiched between the bell and the underside of the sink. Pry the bell housing free and pop it off.
Where to place washers and gaskets on a sink strainer?
Place any included washers and gaskets between the underside of the sink and the locknut or bell housing. A metal-to-metal connection between the sink bottom and the locknut or bell housing won't be watertight. The new sink strainer will come with at least one rubber gasket, and possibly other gaskets or washers made of rubber, cardboard (to protect the rubber), or other materials. Place them as directed in the product instructions before tightening the locknut or bell housing.
How to tighten a locknut on a sink?
Secure the sink strainer into place from below. For a traditional locknut strainer, use a large pipe wrench or strainer locknut wrench to tighten the locknut (by turning it clockwise). Securely press the strainer against the underside of the sink, but don’t feel like you have to tighten it so much that the parts seem ready to fuse together.
How to remove a locknut strainer?
If you also see 3 or 4 screwheads against the locknut, you need to remove these screws before loosening and removing the locknut and strainer. A simple screwdriver (typically Phillips head) will do.
How to immobilize a sink strainer?
If you have trouble squeezing the pliers, you can also insert the handles of the pliers into the openings of the strainer grate, then stick a screwdriver between the handles and hold it steady to immobilize the sink strainer.
How to get a stubborn nut out of a strainer?
If the strainer is spinning counterclockwise along with the nut as you loosen it, you’ll need to hold it still from above. Insert a pair of needle-nose pliers or a sink drain wrench down into the sink and pinch the strainer grate (not the removable strainer basket) to immobilize the entire strainer.
What to do if strainer won't break free?
If the strainer won’t break free, tap it from the underside with a mallet until it pops loose. If you have to bash too hard, though, you may damage the sink itself, so consider calling a plumber if necessary.
