How to Remove a Fence Post The Easy Way
- Step #1 – Dig around the post until six inches of the concrete footing is exposed. ...
- Step #2 – Wrap a chain around the concrete footing of the fence post. ...
- Step #3 – Connect the chain to the High-Lift Jack. ...
- Step #4 – Crank the lever on the high-lift jack to lift the concrete out of the ground. ...
How to remove a rotten fence post from concrete?
- Dig a trench next to the footing and tip the post out.
- Wrap a chain around the post and use a high lift jack to pull the post out.
- Screw lag bolts through a chain into the broken off fence post and then use a vehicle winch/come along/high lift jack to pull the post out.
How to fix a fence post?
Straightening a Leaning Post Set in the Soil
- Remove Any Stress or Weight on the Affected Posts. You need access to the fence post without any interference. ...
- Examine the Post. Check the post carefully. ...
- Remove Soil from the Side of the Post Away from the Lean. ...
- Use a Level to Ensure the Post is Straight Up and Down. ...
- Replace the Soil at the Post Base. ...
- Don’t Get in a Hurry. ...
- Reinstall the Fencing. ...
How to fix a leaning fence post in concrete?
Method 2 Method 2 of 2: Installing Fix-a-Fence Braces for Posts in Concrete
- Purchase 1 Fix-a-Fence post brace per leaning post. A Fix-a-Fence brace is a metal brace that is meant to be set in concrete and then screwed to a leaning ...
- Dig a hole 8 in (20 cm) away from the post with a clam-shell post digger. ...
- Assemble the Fix-a-Fence brace by screwing the pole into the brace. ...
How to remove concrete from a mailbox post?
- Measure the height of your mailbox post. USPS requirements state that a mailbox height must be 41 to 45 inches above the road's surface. ...
- Mark a spot on your lawn six to eight inches back from your curb. If you do not have a raised curb, contact your local postmaster for guidance.
- Use a post hole digger to dig a hole for your post at this spot. ...
How do you remove a broken wood fence post from concrete?
5:076:59Remove a Rotten Fence Post in MINUTES ! - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow if you've had to ever dig out a fence post in the ground snapped off in the ground. Before. YouMoreNow if you've had to ever dig out a fence post in the ground snapped off in the ground. Before. You know it can take a long time because that fence post is in the way of you clearing the concrete. Out
How do you remove a cemented post?
1:542:44How To Remove A Concrete Post Fast & Easy - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere. Simply move the soil from in front of that post. Over into the hole where the other post was.MoreHere. Simply move the soil from in front of that post. Over into the hole where the other post was. Now I'm simply going to take my shovel. Come in behind to post and push it forward just like that.
How do you replace a fence post without removing concrete?
The best way to replace a fence post without removing the concrete footing is by prying it out. You can do this with a long lever and fulcrum or a car jack. In either case, nail some wood to the post first to pry against and then get to work. Pry until the post releases from the concrete and comes all the way out.
How do you break a concrete fence post?
Break the concrete footing into two or more sections, using a cold chisel and steel mallet. Drive the tip of the chisel into the seam between the base of the post and top of the concrete until the concrete breaks. Repeat this on the opposite side of the post.
How do you remove a 4x4 fence post?
0:444:47How to remove a fence post in under 5 minutes...without digging! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this is the thing that gets gets the job done other videos have this I found that this isMoreSo this is the thing that gets gets the job done other videos have this I found that this is actually one of the best ways of course and this is just a hi-lift jack I bought this in at Harbor Freight
Can you reuse a fence post with concrete?
Posts with concrete at the base are the most difficult to remove and reuse because the concrete base is larger than the post, which makes pulling it up through the ground much harder.
How do you replace a wood fence post in concrete?
Dig a hole around 1 side of the fence post. With a shovel, break into the ground surrounding the fence post's concrete base. Keep digging until you create a half-circle gap between the ground and concrete. If possible, dig a hole that is as deep as the concrete itself, giving the post as much wiggle room as possible.
Can you put new fence posts in old holes?
Its a spike shaped like 2 sides of a square if you can picture that, with a section on top for a new post to bolt into. The theory is that you bang it into the old hole then fit new post to it. You need a rubber bung thingy to allow you to bang it in without damaging it.
How do you replace a fence post on an existing fence?
InstructionsDetach Fence From Old Post. Inside Attachment: Go to the rail side of the fence. ... Unscrew Fence From Old Post. ... Remove Old Fence Post. ... Clear Hole or Dig New Hole. ... Lay Gravel. ... Set New Post in Hole. ... Fill Hole With Dry Concrete. ... Add Water to Concrete.More items...•
What tool do I need to break up concrete?
jackhammerA jackhammer is an ideal power tool used for concrete demolitions, and four subcategories of jackhammers exist, including rotary, demolition, combination and breaker options.
How do you break concrete by hand?
InstructionsDig Under the Concrete. Dig out the soil, gravel, or other material from under the concrete, using a shovel and a pickax or mattock. ... Strike the Concrete. Lightly sprinkle the concrete with water to minimize dust. ... Pry Off Stubborn Pieces. ... Move the Concrete Chunks With a Hand Truck.
What can you use to break up concrete?
If you're trying to remove concrete 3 inches deep or more, a jackhammer is your go-to tool. Rentable electric units will likely knock out that run-down sidewalk at the end of the driveway or small patio.
How do you get cemented posts out of the ground?
6:067:41The Fastest and Easiest Way to Remove a Fence Post ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide the chain toward the base of the hi-lift jack. As close as you can to the base. Now simply useMoreSlide the chain toward the base of the hi-lift jack. As close as you can to the base. Now simply use the lever to Jack it up slowly to pull out the post.
How do you remove concrete anchors?
Usually, a screwdriver, pipe wrench, or vise grips can unthread the protruding bolt, leaving the female anchor flush with the concrete. If needed, a hammer can be used to knock the anchoring tube below the floor, and in some cases these tubes can simply be pulled out of the hole entirely.
How do you remove concrete footings?
Ensure that the structure is supported, remove the footing post if applicable. Using a spade shovel manually excavate around the footing at least 3/4 the way around and at least 2/3rds of the length of the footing. Dig until you see the footing wiggle a bit. The more you dig the easier the footing will come out.
How do you break a concrete fence post base UK?
2:253:10How to Remove A Concrete Fence Post Base - Wood Fences - YouTubeYouTubeStart of suggested clipEnd of suggested clipBreak these with a sledgehammer. You know if you're working on a big fence post and again I've seenMoreBreak these with a sledgehammer. You know if you're working on a big fence post and again I've seen some honker out there dig around it get it loose and start beating on it with a sledgehammer.
How do I dig a fence post?
Dig out soil around the post. If the fence post has a large concrete base or is very firmly anchored in soil, you may need to use a farm jack (Hi-Lift jack) and chain to pull it out. To prepare for this, dig out the soil around the post to a depth of 1 to 1½ feet (0.3 to 0.46 meters). A posthole digger will make this easier.
How to fix a hole in a post?
Rock the post in place. Push it backward and forward several times to help loosen the post and plug as the hole is enlarged slightly. Try not to break the post.
How to pull a post up?
The effect will be somewhat like a seesaw, in that as your end moves toward the ground, the tension on the rope increases and pulls the post upward, slowly extracting the buried portion of the post.
How deep should a trench be for a concrete post?
The trench does not have to be any deeper than about 1 foot (0.3 m). Remove the dirt directly around the post, or around the concrete plug that is holding the post in position. Wear eye protection when digging around concrete, to protect against chipped concrete fragments. Soak the remaining soil.
How to wrap a post?
Wrap a chain around the post. Wrap a 3 to 5 foot (0.9 to 1.5 m) length of chain several times around the post, as low to the ground as possible. ...
Can concrete be cracked with a sledge hammer?
Small concrete can be cracked with a sledge hammer. Thanks! Helpful 1 Not Helpful 0. Removing fence posts is easier with 2 people. The weight of a single person may not budge the post, making the homemade lever less efficient, whereas the weight of 2 people will likely be sufficient to extract the post from the ground.
Can you use a square treated post in a rotted out cedar post?
Reuse the old concrete shell if it is solid and in good shape. A round corner square treated post can fit in a concrete shell left from a rotted out cedar post with maybe some minor trimming with a saws-all.
Tools for Removing Fence Post Footings
48″ High-Lift Jack (This is better than any fence post jack you’ll find)
Learn 10 Profitable Handyman Services You Can offer WITHOUT a Contractors License
Stop waiting and start making money. Download this short PDF where I reveal ten of my most profitable, in-demand services that you can start offering today.
How do you remove deck posts from concrete?
Ensure that the structure is supported, remove the footing post if applicable.
How do you remove concrete?
Step 1: Create a Void Under the Concrete. The best way to speed up concrete removal is to create a void underneath the section of slab you’re working on.
What is a post puller?
An electric vehicle having a powered drum for handling wire rope used to pull mine props after coal has been removed; used for the recovery of the timber.
How long will treated posts last in concrete?
A PT post will last a long time in concrete, maybe 5 to 10 years in soil alone. I suggest you embed the post in concrete, trowel a peak around the post so water runs off, and don’t let the PT post come in contact with the ground.
When should I replace my fence post?
Depending on how badly they are damaged, some fence posts will pull right out of the ground. If the wood crumbles in your hands or the rot or termite damage covers more than about 30% of the post, you will need to replace the entire post.
Are concrete fence posts easy to remove?
Thinking a bit more about it, the easiest way to get mine out whole might have been to dig a hole/slot beside the post, tilt it into the hole then pivot/pull it up out of the ground over a log/fulcrum/roller at the end of the slot using the weight of the long post to counterbalance the concrete slug on the end .
How to loosen a post on concrete?
This method is most effective if the other end of the post goes all the way through the concrete slab. Then, the other end will be loose. With some strong back-and-forth movement and some vibration, there’s a small chance it will begin to loosen.
Why Do You Need to Remove a Metal Fence Post?
Whether you have a wood fence or a chain-link fence, metal posts provide excellent structural stability. That is until something goes wrong. Maybe your fence runs alongside a big tree. Mother nature is powerful enough to do many things, including bend metal. Do you have a crooked fence post due to shifting soil or tree roots? If so, then the proper way to fix it is to remove and reinstall it.
How to get rid of vibrations in concrete?
You can rent one from a home improvement store if you don’t happen to have one hanging around your home. Cut away the concrete in a circle around the post.
How to get dirt out of a post?
Wetting the soil around the post with a garden hose can loosen dirt that’s packed too tightly to break through. Just be warned that water will make it messier and the soil heavier to lift.
Can you remove a metal post from a concrete block?
If the post is set in a block of concrete, you might assume to remove the pole from its foundation. But in fact, it’s best to remove both parts together instead of separating the metal post from its concrete foundation.
Can you remove metal posts from a fence?
Metal posts from the middle sections of a fence are often easier to remove than the end posts . Middle supports may require a smaller amount of concrete, while you can set end posts in heartier blocks. So if you’re taking out several posts, start in the middle to perfect your technique and work your way out.
Can you break a fence post in concrete?
Instead of dealing with a few square feet of concrete, the post may be set in continuous concrete. Unfortunately, you can’t break this up as easily as you can a concrete block.
How to lift a post out of the ground?
The key to this method is to use a tall bumper or farm jack with a long lever to provide lots of leverage. Don’t use a floor jack – the smaller wheels and flayed base can make it very difficult to lift a post out of the ground.
How to get a footing out of a hole?
Digging out one side of the footing (such as in the first method described above) and tipping it into the hole, then wrapping a strap or chain around it to lift it out.
What is the advantage of using a digger to pull posts?
The biggest advantage of using machinery to pull posts is speed and ease. A digger can easily lift most posts straight out of the ground, and if you do need to dig any out it saves the labor of removing dirt as well.
How to operate a jack under a post?
When the jack is securely connected or positioned under the post, simply operate the jack the same way you would to lift a car or other heavy object. The jack should loosen the concrete base of the post enough to either pull it out directly or position a pry bar underneath it to finish the job.
Can you pull concrete posts?
If you do choose to rent your own machinery to do the job, make sure you pull the posts gently. Concrete is very strong when compressed, but when it is pulled it is actually relatively fragile. Tugging it out of the ground with too much force could lead to broken or fractured post footings. These in turn will be a big obstacle when it comes to placing new fence posts.
Can you dig fence posts by hand in Texas?
One of the best methods for digging out fence posts by hand is to only remove the dirt around one “face” of the fence post.
Can you remove fence posts from concrete?
The above methods can work for broken posts, but it’s not always easy to make them work.
How many feet of post and concrete below ground?
Add to that any code requirements to accommodate the frost line, and you may have three feet of post and concrete below ground. The trick to removing a fence post is to apply force upward, so that you're not fighting the strength of the earth on either side of the buried post.
Can a concrete jack be pulled from concrete?
Second, consider the width of the concrete pier when you set the jack. If your jack is sitting on top of the concrete, all you'll be attempting to pull the post from the concrete, which will be nearly impossible.
Can you pull a fence post by hand?
But no matter which approach you choose, a little bit of prior thought can save you a lot of effort in the long term.
How do you remove chain link fence from concrete?
Getting it Out of the Ground Clip the metal rings or strips holding the chain link to the posts and roll up the fencing. Lift off the top rail and caps. Dig down along the side of the concrete until you get to the bottom of the post and concrete. Wiggle the post back and forth .
How hard is it to remove a chain link fence?
That said, the task can be quite laborious, so make sure you get some help with the removal to make the job that bit easier .
What is a post puller?
An electric vehicle having a powered drum for handling wire rope used to pull mine props after coal has been removed; used for the recovery of the timber.
How much does it cost to have a chain link fence removed?
The chain link removal cost will be about $2 to $4 per foot. In many cases, this price will include hauling it away. However, some scrap yards will take fencing.
Can you reuse fence posts with concrete?
Pulling up an existing fence post to reuse can be quite a task. Posts with concrete at the base are the most difficult to remove and reuse because the concrete base is larger than the post, which makes pulling it up through the ground much harder.
