You can clear the pilot orifice with a piece of wire or a wire brush, and it isn't difficult to access. Remove the cover plate at the bottom of the water heater. Turn the gas control to the "Off" position.
Full Answer
How do you clean a gas pilot orifice?
How to Clean the Orifice. Once the pilot tube is removed from the orifice, use a fine-grit sandpaper to clean off the tip of the orifice. This can remove any oxidation buildup or mineral deposits that have found their way to the crevices of the gas pilot orifice.
How do I clean the pilot orifice on my Kenmore dryer?
Turn the pilot tube counterclockwise to disconnect the pilot tube from the pilot orifice. Use fine-grit sandpaper to clean the tip of the orifice, removing any oxidation. Push a small, stiff wire through the opening on the pilot to dislodge any clogs. Blow compressed air through the pilot orifice to remove any loose materials from the orifice.
How do you clean the pilot on a gas water heater?
Occasionally or at least seasonally, check the gas pilot orifice for soot or oxidation buildup. A blast of compressed air or a quick turn with a water heater cleaning brush can keep the gas pilot tube and surrounding parts clean and in good working order.
What should I do if my water heater orifice is clogged?
Hunker may earn compensation through affiliate links in this story. A clogged orifice will halt the operation of your gas water heater or other appliance that uses a pilot light to create heat. Cleaning the glass tube to the appliance can keep it in good working order before it becomes a problem.
How do you change a pilot light on an orifice?
Replacing the Pilot Burner OrificeDisconnect the gas supply tubing from the pilot burner.Unscrew the spud orifice and throw it away.Remove any burrs from the tubing and square off the ends.Remove the one-piece nut and ferrule from the new assembly and slip them over the tubing.More items...•
How do you clean the pilot light on a gas orifice?
0:111:35Gas Pilot Cleaner - A 3 Minute Repair - GasPilotCleaner.com - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way to clean a pilot assembly is the only way operating pump once or twice will easilyMoreThe easiest way to clean a pilot assembly is the only way operating pump once or twice will easily clear the ash from the orifice. Inside the pilot assembly.
How do I remove pilot assembly?
2:348:36AO Smith Gas Water Heater Natural Gas Pilot Assembly Replacement ...YouTubeStart of suggested clipEnd of suggested clipHead turn the assembly upright and use the flathead screwdriver. And needle nose pliers to detachMoreHead turn the assembly upright and use the flathead screwdriver. And needle nose pliers to detach the retaining clips securing the insulator. Block. Note the positioning of the wires.
How do you change a water heater orifice?
How to Remove and Clean a Pilot OrificeThe pilot orifice is located at the end of the pilot supply line. ... This is the orifice up close. ... Remove the burner from the water heater. ... Turn the burner upside down and remove. ... Flip the burner back over and raise the. ... Remove the orifice with a box end wrench. ... The orifice removed.More items...
How do you clean a propane orifice?
0:261:10Pilot Orifice Cleaning Pen Vise with Needles - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere. If you just loosen the vise up stick the needle in it and tighten it back down just just likeMoreHere. If you just loosen the vise up stick the needle in it and tighten it back down just just like a almost like a drill bit you can take and get it into the office.
How do you clean a clogged pilot light?
Use your pliers or wrench to remove the pilot light and thermocouple from the bracket. Using the wire brush, brush away the carbon buildup and soot from both components. For hard to reach areas and stubborn buildup, use the metal file. Wipe away dust with a soft cloth or burst of compressed air.
How do you replace a furnace pilot assembly?
2:275:18Furnace - Thermocouple | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipBe careful not to scratch the coating. Next insert the thermocouple into the pilot assembly. NowMoreBe careful not to scratch the coating. Next insert the thermocouple into the pilot assembly. Now screw the thermocouple into the gas valve.
How do you replace a gas fireplace pilot assembly?
4:2411:51How to Replace the Pilot Light Assembly on a Gas FireplaceYouTubeStart of suggested clipEnd of suggested clipThe same thing just loose just turn it. And it comes right off okay so those wires are fedMoreThe same thing just loose just turn it. And it comes right off okay so those wires are fed underneath. The fireplace so i just pick it up a little bit. And pull them right out.
How do you change a pilot light on a gas fireplace?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it's been since the gas fireplace was last used, ignition may take multiple attempts.
How do you remove the pilot tube on a water heater?
1:523:00Water Heater Pilot Keeps Going out - CLEAN THE FILTER GRATE! Most ...YouTubeStart of suggested clipEnd of suggested clipSo spend a couple minutes clean up that grate. And then. You can put this cap back on by the way youMoreSo spend a couple minutes clean up that grate. And then. You can put this cap back on by the way you don't have to take this cap off I just did that for demonstration purposes.
Where is the orifice on a hot water heater?
1:013:11How to check the gas pilot orifice - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow this is the orifice right here. There you go you can kind of see what it looks like it's muchMoreNow this is the orifice right here. There you go you can kind of see what it looks like it's much smaller hole than that and I'm going to look at these holes close here in a minute.
How do you get air out of gas hot water heater?
0:131:40How to Get Air Out of the Lines for the Hot Water Heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd into your drain. But it also works great to allow the air to get out of your tank. That way theMoreAnd into your drain. But it also works great to allow the air to get out of your tank. That way the more water can come in and actually the only area you'll have to get out is in the lines above.
How to clean a pilot tube?
How to Clean the Orifice. Once the pilot tube is removed from the orifice, use a fine-grit sandpaper to clean off the tip of the orifice. This can remove any oxidation buildup or mineral deposits that have found their way to the crevices of the gas pilot orifice.
Why do you need to clean the glass tube on a pilot light?
If the orifice is gunky with grime, a quick cleaning can give new life to a nonworking appliance. If the pilot light is covered in carbon residue or soot, it needs a good cleaning in order to get the appliance to roar back to life.
What is the purpose of a pilot tube?
The pilot tube supplies a small amount of gas directly to the pilot orifice. This is what creates the tiny flame that is responsible for heating the tip of the thermocouple.
How to stop gas from flowing to water heater?
Turn it clockwise to halt the flow of gas to the water heater. Loosen any nuts that hold the tube or orifice together or attaches it to the appliance.
