How to Remove Plastic Nuts on a Faucet
- Using a Basin Wrench The basin wrench was invented for faucet removal, says Liberty Plumbing, Heating and Air Conditioning, and it's designed to reach into the tight space behind the sink where an ordinary wrench won't go. ...
- Tapping With Screwdriver and Hammer The plastic nibs that prevent the wrench from gripping are there for a reason. ...
- Use Heat or Calcium Dissolver ...
Can you use a basin wrench to remove stuck nuts?
Most plumbers reach for a basin wrench to remove stuck metal nuts, but plastic ones often have wings that prevent the wrench from gripping. It's still worth a try, but chances are you're going to have to resort to other measures.
How do you remove a stuck plastic nut from a faucet?
Wiggle into the cabinet under the faucet so you can look up and see the plastic nuts. Attempt to turn the nut by hand counterclockwise. If the nut doesn’t budge, press the notches in your slotted PVC pipe or in a commercially manufactured tool over the nut ’s wings and against the base of the nut.
How to remove a lock nut from a toilet tank?
Using pliers or a spud wrench, you can loosen the nut that secures the toilet tank. After you have cut off the water supply and emptied out the tank, you will have to get a couple of tools to remove the lock nut. It is easy to find the hose connecting to a toilet’s water supply.
How do you remove a PVC pipe from a faucet?
Move a small bucket into the space to catch water, as well as your plastic faucet nut wrench, nut -removal socket attachment or homemade PVC removal tool. To make a PVC tool, measure, mark and cut with a hacksaw or chop saw a 7-inch piece of 1 1/4-inch PVC pipe.
How to loosen a plastic nut?
How to shut off water supply valves?
How to make a PVC tool?
Can you use plastic nuts on a faucet?
See 1 more
About this website
How do you remove a sink basin nut?
0:092:20How to loosen kitchen faucet nuts with a basin wrench - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou get into extremely tight spots I've used vise grips but this is the ideal tool of art. You canMoreYou get into extremely tight spots I've used vise grips but this is the ideal tool of art. You can see that it's got a spring-loaded jaw here great in cramped spaces.
How do you remove a plastic faucet connector?
0:001:19Faucet quick-connect removal (on kitchen faucet spray hose) This one ...YouTubeStart of suggested clipEnd of suggested clipOn it's firmly in place push down on this ring push down on this ring. That's the tabs. When you'reMoreOn it's firmly in place push down on this ring push down on this ring. That's the tabs. When you're taking the whole thing off but make sure it's in that position before you start let's go to push.
How do you remove a plastic sink faucet nut?
3:524:50Remove Plastic Faucet Nut Tips & DIY Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a hammer and a screwdriver to tap the nut and turn it counterclockwise. Use a hammer. And aMoreUse a hammer and a screwdriver to tap the nut and turn it counterclockwise. Use a hammer. And a chisel to cut the nut.
How do you remove push to connect plastic fittings?
0:081:08How to remove Push to Connect fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust use a wrench. This is a 3/4 inch line 13/16 wrench just push it on here this is really chewedMoreJust use a wrench. This is a 3/4 inch line 13/16 wrench just push it on here this is really chewed up but it'll go on the other end too just going to give it a good push on.
How do you remove a faucet connector?
Turn the water off hot and cold water supply lines underneath the sink.Place a bucket underneath the faucet connections.Turn on the faucet to release water pressure in the faucet.Turn the Metal Clip counter-clockwise by hand to release it.More items...•
How do you remove a quick connector from a faucet?
Center & Right image: Pinch together at the ridged, square tabs on the sides of the fitting. It may help to push up on the fitting if the tabs are not compressing. Do not pull the tabs out as that may lock the hose to the tube. Pull down gently to remove the quick connect hose.
How do you remove a faucet sprayer connector?
0:201:13Maintenance - How To Remove a Sprayer Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe pressure from the faucet by rotating the handle to the open. Position to remove the sprayer hoseMoreThe pressure from the faucet by rotating the handle to the open. Position to remove the sprayer hose connection push up on the Quick Connect housing.
How do you get a faucet adapter out?
0:262:42Replacing a Faucet Aerator...that's stuck! - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might try a rubber jar opener.MoreYou might try a rubber jar opener.
Removing old plastic nuts - Plbg.com
Re: Removing old plastic nuts; Author: plumbhelp (MA) u can use whats called a basin wrench. they are normally used to tighten and remove those nuts when they are brass. but i've used the wrench on the tough plastic nuts also. when u mount the new faucet, put some pipe dope, or never seize on the threads, then draw up the new nuts. good luck.
How to Remove Plastic Faucet Valves | Home Guides | SF Gate
How to Remove Plastic Faucet Valves. Over time, you may need to replace your home's plastic faucet valves due to leaking seals or stripped stems. There's no need to call a plumber, as this is a ...
How to loosen a plastic nut?
Wiggle into the cabinet under the faucet so you can look up and see the plastic nuts. Attempt to turn the nut by hand counterclockwise. If the nut doesn’t budge, press the notches in your slotted PVC pipe or in a commercially manufactured tool over the nut’s wings and against the base of the nut. Turn the tool counterclockwise to loosen ...
How to shut off water supply valves?
Turn the water supply valves by hand counterclockwise to shut them off. Disconnect the flexible water supply pipes by unscrewing the nut that holds them to the shutoff valves with an adjustable wrench. Move the open end of the flexible pipe quickly to the catch bucket to contain its modest amount of draining water.
How to make a PVC tool?
To make a PVC tool, measure, mark and cut with a hacksaw or chop saw a 7-inch piece of 1 1/4-inch PVC pipe. Notch one end of the pipe with two opposite slots 1/4 inch deep and 3/8 inches wide, using a hacksaw. The slots will grasp the projecting wings on the plastic nuts. If on inspection you find more than two wings -- there may be four -- cut ...
Can you use plastic nuts on a faucet?
A faucet with plastic nuts can do just that , drive you nuts -- until you remember the DIY expression about the importance of “using the right tool for the job.”.
How to loosen a plastic nut?
Whether you use a basin wrench or a hammer and screwdriver, the nut is easier to loosen if you heat it with a hairdryer. The heat should soften the plastic and make the nut pliable enough to break free. It also helps to spray some calcium dissolver on the nut and wait several minutes before tapping or twisting. Spraying lubricant, such as WD-40, is a third option, but it's flammable, so don't use it in conjunction with heat.
What wrench to use to remove stuck nuts?
Most plumbers reach for a basin wrench to remove stuck metal nuts, but plastic ones often have wings that prevent the wrench from gripping. It's still worth a try, but chances are you're going to have to resort to other measures. Advertisement.
How to loosen a nut on a flat head screwdriver?
They provide a surface against which you can set the head of a flat-head screwdriver, which you can then tap with a hammer to loosen the nut. You can't always get the screwdriver at the optimum angle for tapping, but as long as you can tilt it in any direction other than perpendicular to the washer, you should be able to generate enough force with the hammer to loosen the nut.
What is a basin wrench?
The basin wrench was invented for faucet removal, says Liberty Plumbing, Heating and Air Conditioning, and it's designed to reach into the tight space behind the sink where an ordinary wrench won't go. It's easy to use one:
Why is it so hard to replace a faucet?
The most difficult part of replacing a faucet is removing the old one, and that's because the nuts holding it to the countertop or sink deck are invariably stuck, and for good reason. They have been in the moist confines of the sink cabinet for years, and mineral deposits have had all that time to collect in the threads.
Can you use WD-40 on plastic nut?
Spraying lubricant, such as WD-40, is a third option, but it's flammable, so don't use it in conjunction with heat. Advertisement.
How to remove lock nut from plastic?
Use caution as not to go too deep or cut through anything else. Once you have cut through the nut, use the flathead screwdriver to push the two ends apart , then remove the lock nut with your hands.
How to loosen a faucet nut?
To loosen faucet mounting nuts, use channel-type pliers to grip the nut that holds the faucet body in place. Rotate the nut counterclockwise to remove it. There may also be a spout mounting nut. If there is, use the same techniques.
How to remove a hex nut?
To remove the nut, you can use whichever tool you choose: a pair of pliers, a spud wrench (specifically designed for removing hex nuts), or an adjustable wrench. Turn the plastic nut counterclockwise to remove it.
What are the plastic lock nuts on toilets?
In every toilet tank, there are plastic lock nuts that secure various fixtures in place. They are strong enough to provide solid support to secure the fill valve and other fixtures. However, one misstep can damage the locknut, making it a nightmare to remove.
How to fit a lock nut?
Set the pliers on the narrowest setting that will fit around the lock nut. Fit the pliers around the lock nut. Come from either the top or bottom, not the side. Using both hands, grip the pliers while rotating to spin the nut.
Can plastic nuts be used on faucets?
Plastic nuts on faucets can be a bit tricky , as some of them may have shapes that prevent a basic basin wrench from efficiently removing it.
Can you use an angle grinder to cut plastic?
If all other methods fail to do the trick, you can try using an angle grinder to slice through the plastic. This method may not always do the trick because some angle grinders will not fit in the close quarters of the tank.
How to unscrew a lock nut?
Grip the loosened lock nut between your thumb and forefinger, and unscrew it all the way. Spin the nut counter-clockwise until it leaves the threads of the bolt.
How to release lock nut?
Unscrew any fasteners from the bolt on top of the lock nut. With your hands, pliers or a wrench, twist these counter-clockwise until they release.
Why do plastic nuts work?
Pliers or wrench. Lock nuts prevent vibration from loosening connections between fasteners. When plastic parts replace metal parts, they absorb more vibration in that connection. Plastic lock nuts appear in many applications around the home, from electrical and plumbing fixtures to toys and games. But, because they are softer than metal, remove ...
Can you use a metal plier to remove a lock nut?
Be as gentle as possible. Metal pliers or wrenches may deform the plastic so you can't use the lock nut again once it is removed.
How to loosen a plastic nut?
Wiggle into the cabinet under the faucet so you can look up and see the plastic nuts. Attempt to turn the nut by hand counterclockwise. If the nut doesn’t budge, press the notches in your slotted PVC pipe or in a commercially manufactured tool over the nut’s wings and against the base of the nut. Turn the tool counterclockwise to loosen ...
How to shut off water supply valves?
Turn the water supply valves by hand counterclockwise to shut them off. Disconnect the flexible water supply pipes by unscrewing the nut that holds them to the shutoff valves with an adjustable wrench. Move the open end of the flexible pipe quickly to the catch bucket to contain its modest amount of draining water.
How to make a PVC tool?
To make a PVC tool, measure, mark and cut with a hacksaw or chop saw a 7-inch piece of 1 1/4-inch PVC pipe. Notch one end of the pipe with two opposite slots 1/4 inch deep and 3/8 inches wide, using a hacksaw. The slots will grasp the projecting wings on the plastic nuts. If on inspection you find more than two wings -- there may be four -- cut ...
Can you use plastic nuts on a faucet?
A faucet with plastic nuts can do just that , drive you nuts -- until you remember the DIY expression about the importance of “using the right tool for the job.”.
