Sillcock Repair Tip:
- Remove sillcock handle, and loosen retaining nut with channel-type pliers. Remove stem. Replace O-ring found on retaining nut or stem.
- Remove the brass stem screw at the end of the stem, and replace the washer. Reassemble the sillcock.
How do I replace the inside stem on my sillcock?
When looking to replace your inside stem, use the following steps and diagram below to help accurately size your replacement stem: 1. Remove the screw from the center of the handle then remove the handle from the sillcock. 2. Remove the packing nut using a suitable tool.
How do I remove the sillcock from the door handle?
Remove the screw from the center of the handle then remove the handle from the sillcock. 2. Remove the packing nut using a suitable tool. Set the packing nut aside in a safe place.
How do I replace the inside stem on my vacuum cleaner?
Pull straight out to remove the entire inside stem assembly. Do not attempt to “twist” or “screw” the inside stem out. The vacuum holding the stem in place may make it difficult to pull it out, but it will come out. 4. Measure the inside stem from tip to tip without the handle or silver nut attached to it. Please refer to the measuring guide below.
Why is my sillcock stem measurement off?
If your stem measurement is off, double check your sillcock is a BK branded sillcock. Our measurements and stems are not the same as our competitors. If it is a BK Products model and you are not getting the right measurement, then it is possible that part of the stem broke off and is still inside the casing located in your wall.
What to do if your sillcock is off?
How long do sillcocks last?
Does the stem need washers?
Does the cartridge fit all sillcocks?
Is a sillcock frost free?
How do you remove an outdoor faucet stem?
0:073:59Repair Outdoor Faucet - traditional style - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe same you take out that lower nut and the entire stem. And handle will unscrew with it and on theMoreThe same you take out that lower nut and the entire stem. And handle will unscrew with it and on the bottom you can see the two nuts here yep. You've got a washer held in with the screw.
How do you remove a Sillcock valve?
1:454:46How to Replace an Outdoor Faucet with a Frost-Proof Sillcock - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut it around the pipe snap it together and then just spin it around in the direction the arrow.MorePut it around the pipe snap it together and then just spin it around in the direction the arrow. Pretty cool cutter surfeit go got it a little bit of water.
How do you change a washer on a Sillcock?
0:213:15How to Fix a Leaky Frost Free Sillcock / Outdoor Faucet video - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff I'm going to take off the center screw. Then remove the handle. And then underneath this nut isMoreOff I'm going to take off the center screw. Then remove the handle. And then underneath this nut is a washer and a lot of times the problems in this washer.
How do you fix a leaky outdoor frost free faucet?
1:493:02Fixing Faucets : How to Repair a Leak in a Frost-Proof Water FaucetYouTubeStart of suggested clipEnd of suggested clipYou'll need to remove the bib washer first remove the screw. And then take your pick or knife andMoreYou'll need to remove the bib washer first remove the screw. And then take your pick or knife and remove the bib washer. Once you have your new washer you've matched up the proper.
What is the cap on top of an outdoor faucet?
The vacuum cap is circular and about an inch in diameter, and it either slips or screws onto the top of the faucet. The device underneath it is known as a vacuum breaker or an anti-siphon valve.
How do I loosen my outdoor faucet?
Contents show1.1 Step 1: Turn It With a Wrench.1.2 Step 2: Heat It With a Hairdryer.1.3 Step 3: Brush It With a Wire Brush.1.4 Step 4: Cover It With Plumber's Grease.1.5 Step 5: Soak It With Vinegar.
How do you replace a rubber washer on an outside faucet?
1:112:35How to Fix a Leaky Outdoor Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the old washer to a plumbing supply store to make sure you're replacing it with the right oneMoreTake the old washer to a plumbing supply store to make sure you're replacing it with the right one put the new washer back inside the packing nut and retighten.
How do you change a washer on a hose bib?
InstructionsShut off the Water. Begin by shutting off the water to the hose bib. ... Remove the Handle. ... Unscrew the Packing Nut. ... Remove the Valve Stem. ... Replace the Stem Washer. ... Replace the Packing String. ... Reassemble the Faucet. ... Test the Faucet.
How do you remove a tap head with no screws?
0:545:17how to remove a tap with no screw with Inspire DIY Kent ThomasYouTubeStart of suggested clipEnd of suggested clipKey if they don't have a grub screw around the back then they'll be the type that unscrews.MoreKey if they don't have a grub screw around the back then they'll be the type that unscrews. Sometimes you can just twist them off sometimes they're really tight.
Will a leaking outdoor faucet freeze?
Draining the outside faucet is critical, because standing water between the inside shut-off valve and the outdoor faucet can freeze and break both the fixture and shut-off valve. Creating an air space within the short segment of pipe gives any residual water room to expand if it freezes.
How do you fix an outdoor faucet that won't shut off?
Outdoor Faucet Won't Turn Off? Here's 5 Steps to Fix ItTurn off the water supply to the faucet.Drain the water from the faucet.Remove the packing nut.Remove the valve stem.Reassemble the faucet with a new parts where necessary.
Which way does a cone washer go?
The washer goes on to the bolt in one way or another. The conical tooth washer needs to be positioned so the teeth face the hitch. It cannot come loose because of that.
What is cone washer?
Cone washers are used to create a leak proof seal at the water supply inlet. They are used on both faucets and toilet ball-cocks. Replacing a worn washer is an easy DIY project. New washers eliminate leaks which waste both water and energy and can damage floors.
How do you put a spring back on a washing machine?
0:070:49LG Washer Replace Door Boot Seal Retaining Ring #2W20017EYouTubeStart of suggested clipEnd of suggested clipOr a spring expansion tool to help remove the old clamp from the door boot seal install the new doorMoreOr a spring expansion tool to help remove the old clamp from the door boot seal install the new door boot clamp by inserting it into the seals outer groove. With the spring at the bottom.
How do you remove a washing machine door?
0:239:05How to dismantle and replace Washing Machine door partsYouTubeStart of suggested clipEnd of suggested clipAlways make sure you've got one hand on the door while undoing the screws to support it. Now with aMoreAlways make sure you've got one hand on the door while undoing the screws to support it. Now with a little bit of a jiggle. You'll actually slide the hinges. Out.
What to do if your sillcock is off?
If your stem measurement is off, double check your sillcock is a BK branded sillcock. Our measurements and stems are not the same as our competitors. If it is a BK Products model and you are not getting the right measurement, then it is possible that part of the stem broke off and is still inside the casing located in your wall. This part needs to come out. If necessary, please call a plumber or a professional to help you with this. Our Customer Service Representatives are not trained or equipped to assist you with these issues.
How long do sillcocks last?
The average industry lifespan for a frost-free sillcock is 10 years.
Does the stem need washers?
The stem is a redesign of the discontinued quarter-turn sillcock and does not require any washers or gaskets.
Does the cartridge fit all sillcocks?
The cartridge will fit all lengths of this particular sillcock, but will NOT fit any other models.
Is a sillcock frost free?
No, this is an industry standard identifying the sillcock as a frost-free sillcock. The number does not help identify which replacement parts you need.
What to do if your sillcock is off?
If your stem measurement is off, double check your sillcock is a BK branded sillcock. Our measurements and stems are not the same as our competitors. If it is a BK Products model and you are not getting the right measurement, then it is possible that part of the stem broke off and is still inside the casing located in your wall. This part needs to come out. If necessary, please call a plumber or a professional to help you with this. Our Customer Service Representatives are not trained or equipped to assist you with these issues.
How long do sillcocks last?
The average industry lifespan for a frost-free sillcock is 10 years.
Does the stem need washers?
The stem is a redesign of the discontinued quarter-turn sillcock and does not require any washers or gaskets.
Does the cartridge fit all sillcocks?
The cartridge will fit all lengths of this particular sillcock, but will NOT fit any other models.
Is a sillcock frost free?
No, this is an industry standard identifying the sillcock as a frost-free sillcock. The number does not help identify which replacement parts you need.
