- Check the shower drain for screws. Some shower drains are attached with screws while others are tightened in without them.
- Insert 2 nose pliers into the drain openings. Hold a pair of nose pliers in each hand—you will need two separate sets to remove the drain.
- Grab the plier handles firmly with both hands. Most drains are screwed into the drain hole and must be twisted out.
- Continue twisting the drain until it is entirely loosened. When you reach the end of the screwed portion of the shower drain, it can be lifted out of the ...
How to clear a drain without drain cleaner?
- Snake, Wire Hanger or Plunger. These are the simplest, most obvious methods most people use to unclog a drain. ...
- Dish Soap & Hot Water. Another great natural way to unclog your slow drain is to use dish soap and hot water. ...
- Baking Soda and Vinegar. It’s just like those volcanos that would win the science fair in grade school, except now you want to contain all the foam instead of ...
- Hydrogen Peroxide. Hydrogen peroxide can also be used to unclog your drain. Mix a cup of hydrogen peroxide with a tablespoon of baking soda.
How to clean out your drains?
How to clean your drains in 10 minutes
- Use baking soda to clean drains. Start to clean your drains with a cup full of baking soda – a cheap multipurpose product found in your local grocery ...
- Microwave 1 cup of vinegar. Place a cup of white vinegar into the microwave for two minutes (the added bonus with this step is the steam from the ...
- Pour vinegar down the drain. ...
- Leave for 5 mins. ...
How do drain cleaners unclog drains?
- Drain standing water. ...
- Pour 1 cup of baking soda down the drain. ...
- Add another cup of vinegar slowly down the drain. ...
- Wait for 15 minutes for the reaction to take place and the solution to work out its magic.
- Meanwhile start boiling about a gallon or more of water.
- Dump the boiling water down the drain and check if the fixture drains out fast.
How to remove a radiator without draining it?
You will need:
- New radiator valves
- Old towels or sheets
- Adjustable spanner
- Pair of grips
- Wet & dry vacuum or large container
- PTFE tape
- Radiator bleed key
How do you remove an old tub drain?
0:002:02Remove Stuck Old Tub Drain - FREE AND EASY!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOld tub drain this is the freest most likely and pretty easy way to get these annoying things out weMoreOld tub drain this is the freest most likely and pretty easy way to get these annoying things out we need a hacksaw a chisel a hammer hair dryer step one we're gonna cut a little notch.
How do you remove a bathtub drain with broken cross members?
4:185:36How to remove bathtub drain with broken cross members - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just create some resistance in the drain. Turn counterclockwise. And you'll get the drain. OutMoreAnd just create some resistance in the drain. Turn counterclockwise. And you'll get the drain. Out if your threads are you know messed up like these were this is how um the drain.
What can you use instead of a drain wrench?
Short of a plug wrench, the best substitute is a set of needle-nose locking pliers. The pliers need to be small enough to reach into the drain and through the cross. Once the locking pliers are secured, you use a pair of standard pliers to turn the locking pliers and loosen the drain.
How do you remove a drain without a drain tool?
0:454:26DIY Bathtub Drain Removal and/or Installation Tool and ProcedureYouTubeStart of suggested clipEnd of suggested clipSo what we do is we take put the needle nose pliers. Down in the hole on the holes neither side ofMoreSo what we do is we take put the needle nose pliers. Down in the hole on the holes neither side of the collar.
How do you remove tub drains with crossbars?
If your drain fitting has these crossbars, insert a drain wrench into the cross shape and turn counterclockwise to unscrew it. (There are two ends to the wrench; use the side that offers the best fit.) You can also try using a pair of needle-nose pliers to grip the X and unscrew the drain fitting.
Are all tub drains threaded?
There are several different styles of tub drain -- two of the most common are threaded and drop-in drains. Threaded drains are usually found in older tubs, while the drop-in version is common in newer models. Determining whether you have one or the other involves a bit of inspection.
How do I disassemble a sink drain?
0:233:05Plumbing Advice : How to Remove a Sink Drain Assembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your pliers loosen the locknut from the bottom. That may take a minute sometimes they're aMoreTake your pliers loosen the locknut from the bottom. That may take a minute sometimes they're a little bit rusty. Once you get that removed. You'll want to work the drain assembly. Up.
How much is a drain wrench?
Compare with similar itemsThis item Superior Tool 06020 Tub Drain Wrench (Dumbell Wrench)-Dual Ended Drain Wrench that fits 3/8 or 1/2 Inch Ratchet WrenchAdd to CartCustomer Rating4.6 out of 5 stars (2183)Price$1049Sold ByOhio Supply3 more rows
What tool do you use to remove a tub drain?
A drain wrench is a drain removal tool that is form-fitted to drain basket crossbars. It greatly reduces the risk of accidentally breaking the crossbar. If you are using a drain wrench, insert the drain wrench into the drain and turn it counterclockwise to unscrew the drain basket.
How do you use a drain removal tool?
0:010:27Tub Drain Extractor - Tub Drain Removal Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you're going to use a half inch ratchet drive with an extension you're going to turn itMoreAnd then you're going to use a half inch ratchet drive with an extension you're going to turn it counterclockwise. And it'll unscrew the old drain. So a very effective tool especially.
How do you use a drain key tool?
1:2813:16Bathtub Drain Replacement | Removal and Installation Using a Drain KeyYouTubeStart of suggested clipEnd of suggested clipTurn this it pushes them down into the hole and these rings expand you can see they're split. WellMoreTurn this it pushes them down into the hole and these rings expand you can see they're split. Well they expand into the hole. And basically just lock it down.
How do you fix a corroded bathtub drain?
6:3215:12Replace that Corroded Tub Drain - Easy! - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere just create a clean dry surface for the new drain new drain here comes with the gasket. AllMoreHere just create a clean dry surface for the new drain new drain here comes with the gasket. All right simple as this here. This is the action just a dry fitted.
How do you remove a broken trip lever drain stopper?
0:111:51Bath tub trip lever/ bath tub stopper replacement or adjustnment.YouTubeStart of suggested clipEnd of suggested clipSo to remove it we're first going to take our Phillips or flat screwdriver whichever screws needs toMoreSo to remove it we're first going to take our Phillips or flat screwdriver whichever screws needs to remove. Them.
How do I retrieve a detached plunger from a bathtub drain?
Simply remove the overflow plate (2 screws) and pour some CRYSTAL drain cleaner down the overflow tube using a funnel. Using a funnel again, pour some cold water down the tube (about 3 cups) let it clean the crud out.
How to tighten a locknut on a sink?
Secure the sink strainer into place from below. For a traditional locknut strainer, use a large pipe wrench or strainer locknut wrench to tighten the locknut (by turning it clockwise). Securely press the strainer against the underside of the sink, but don’t feel like you have to tighten it so much that the parts seem ready to fuse together.
How to remove a locknut strainer?
If you also see 3 or 4 screwheads against the locknut, you need to remove these screws before loosening and removing the locknut and strainer. A simple screwdriver (typically Phillips head) will do.
What happens if a putty seal gets damp?
If the tissue gets damp at all, your putty seal is the likely culprit and you’ll have to re-do the installation. If this spot passes the “tissue test,” let the water out of the sink and run a dry tissue around the nut that connects the strainer to the drain pipe. If it stays dry, you’re good to go!
How to immobilize a sink strainer?
If you have trouble squeezing the pliers, you can also insert the handles of the pliers into the openings of the strainer grate, then stick a screwdriver between the handles and hold it steady to immobilize the sink strainer.
How to get a stubborn nut out of a strainer?
If the strainer is spinning counterclockwise along with the nut as you loosen it, you’ll need to hold it still from above. Insert a pair of needle-nose pliers or a sink drain wrench down into the sink and pinch the strainer grate (not the removable strainer basket) to immobilize the entire strainer.
What to do if strainer won't break free?
If the strainer won’t break free, tap it from the underside with a mallet until it pops loose. If you have to bash too hard, though, you may damage the sink itself, so consider calling a plumber if necessary.
What is a bell washer strainer?
Bell washer sink strainers have an outer bell-shaped “shell” that fits over the entire strainer.
What to do if drain is too rusty?
If your drain is too rusty to remove or significantly clogged, hire a plumber to remove it for you.
How to get rid of a swollen drain?
Send a handful of baking soda and hot water down the drain.
Can you drop screws down the shower drain?
Be careful not to drop any screws down the drain. Set them aside somewhere safe and outside of the shower in case you will be putting the shower drain back in later.
Can you use WD-40 to loosen a drain?
Buy a drain or spray lubricant, like WD-40, silicone lubricant, or PTFE. If your drain is rusty, WD-40 is ideal. Do not pour grease or fat down your drain in an attempt to loosen it.
Who is James Schuelke?
James Schuelke. Professional Plumber. James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California.
Tips To Remove Old Tub Drain
Tub drains are sometimes hard to remove. They accumulate muck, rust, or toughened plumber’s putty.
REPLACE THE OLD TUB DRAIN
Don’t throw away the old tub drain if you want to install a new one. Installing an accurate size for the tub drain is important.
How To Know If You Installed New Tub Drain Successfully?
If you follow the wrong installation process, you may experience leakage issues in your bathtub.
When to Call a Pro?
If you’ve broken the drain basket while removing it, getting professional help is necessary. You can’t handle the task if the stopper or basket isn’t coming out.
Recent Posts
link to CeraVe Hydrating Cleanser Vs. Foaming Cleanser: Key Differences
How to get water out of a P trap?
Set a bowl under the "P" trap to catch the water that is trapped in it. Loosen the nut just enough to know it is loose. Then locate the nut on the back of the "P" trap. Loosen it all the way and gently pull down on the "P" trap to remove it from the tailpiece. Clean up any water that might have spilled onto the bottom shelf ...
Where is the nut on a kitchen sink?
Locate the nut on the underside of and right next to the sink bowl. Reach in with your hand to get an idea of what you are working with. Be certain that you remove any debris around the area to avoid getting it in your eyes if you have to place your head inside the cabinet. Advertisement.
Can you cut a drain pipe nut off?
Back the nut off slowly, as it can get cross-threaded and become very difficult to remove. If this occurs, the nut or the drainpipe will have to be cut off. This is generally accomplished with a hacksaw.
Can you remove a P trap without gloves?
Do not remove the "P" trap without rubber gloves if the sink drain has recently been unstopped with a chemical drain cleaner. Do not allow debris to fall into the "P" trap when reinstalling it.
Who is the author of What a Strange Little Man?
ABOUT THE AUTHOR. Michael Straessle. Michael Straessle has written professionally about the construction industry since 1988. He authored “What a Strange Little Man,” among other books, and his work has appeared in various online publications.
How to remove a pop up stopper?
To remove one, set it to the open position and turn the stopper in a counterclockwise direction to unscrew it. Next, unscrew the shaft.
Why does my bath drain slowly?
If your bath begins to drain slowly or stops draining completely, it has probably become blocked by a build-up of hair and grime. This means you will need to remove the drain and unblock it. You will also need to remove an old drain to replace it with a new one. Of course, you can call in a professional plumber to do it for you.
What do you need to do before you can remove the bathtub drain?
There are many different types of stopper, and the first thing you need to do before you can remove the bathtub drain is to remove the stopper. Here are examples of how to do it with two of the more common versions.
How to get rid of a swollen drain?
You can do this by heating it. The easiest way is to use a hairdryer – simply use the hairdryer to blow hot air into the drain for a few minutes before removing it.
What is a screen in a drain?
The screen is the grille that is designed to prevent larger objects from falling into the drain. You also need to remove this before you can gain access to the drain.
Where should a drain wrench fit?
Drain wrenches have different heads, so the first thing you need to do is find one that fits your drain – it should fit comfortably over the cross at the bottom of the drain.
Can you remove a bathtub drain?
Removing a bathtub drain is a simple task that just about anyone can manage. If this is something you need to do, just follow our step-by-step guide and you should be able to manage it without too much trouble.
Identify the Type of Bathtub Drain Stopper
Bathtub drain removal starts with identifying the type of drain stopper your bathtub has so that you can use the proper removal technique. The drain stopper is the part of the drain that opens and closes to either empty or fill the tub. It is the most recognizable part of the drain.
Toe-Touch Drain Stopper
A toe-touch drain stopper is spring-loaded and designed to be opened and closed with just a press of your toe. This stopper is convenient and easy to install, although the spring may need to be replaced with age and frequent use.
Push-Pull Drain Stopper
Also known as a foot plug, a push-pull drain stopper opens and closes just as its name describes. You pull up on its small knob to open the drain and push down to close it again. This simple drain stopper is easy to remove and install and has a long lifespan.
Lift-And-Turn Drain Stopper
A lift-and-turn drain stopper or twist-and-pull drain stopper appears similar to a push-pull drain stopper, since both types have small knobs on the top. This drain stopper opens by turning it clockwise while pulling up slightly on the knob and closes by turning it counterclockwise.
Trip-Lever Drain Stopper
Of these four drain stoppers, the trip-lever drain stopper—also called a flip-level drain stopper—is the most distinctive, which means it requires a different removal technique. You operate this drain stopper by using a trip lever that is installed on the overflow drain on the side of the tub, just below the faucet.
Remove the Bathtub Drain Stopper
Once you have identified the type of drain stopper, you can learn how to remove a bathtub drain by following the specific directions below for your type of drain:
Remove the Drain Basket
Once you have removed the drain stopper, you will see the drain basket (also known as a drain flange) in the drain opening. The drain basket will have a metal crossbar at the bottom.
