how do you remove an old towel rack

1. Remove the bar section of the towel rack by pulling one side in if it's a tension bar. ...
2. Apply several layers of masking tape to the drywall or tile surrounding the towel rack holders. This helps protect them from damage.
3. Saw along the edges of the towel rack holders using a grout saw to break the outer seal holding the ceramic holders to the wall.
4. Place a chisel in the space between the holders and the wall that you created with the grout saw. ...
5. Place a pry bar between the holder and the wall over the masking tape. ...
6. Sand away any cement remaining on the wall with a sanding block or hand sander. Pay close attention so you sand only the cement, and not the wall itself.
7. Repeat the process with the second towel rack holder. Repair the holes where the towel rack holders were cemented by patching the drywall with drywall tape or fiberglass mesh ...

Full Answer

How do you remove a towel rack from the wall?

To remove a ceramic fixture, such as a towel rack, from a drywall surface, you must:

• Cut through the plastic bar that spans between the two ceramic posts.
• Tape the wall around the base of each ceramic towel bar post.
• Use an oscillating multi-tool to cut through the adhesive between the wall and the towel bar holders.
• If absolutely necessary use a hammer along with a chisel or pry bar to pop the towel bar holders from the wall.

More items...

How to take a towel rack off the wall?

Removing A Towel Bar From The Wall

1. Find the Screws. Depending on the towel bar that you own, there may be screws fastening it to the wall. ...
2. Remove the Screws. Using a hex key or Phillips head screwdriver, you can now remove the screws from the towel bar. ...
3. Remove the Wall Brackets. If your towel bar is attached to wall brackets, you will need to remove them. ...
4. Patch the Holes. ...

How to fix a loose towel rack?

How to fix a loosened towel rack without drilling?

1. Take out the old towel rack and unfasten any screws that remained.
2. Use the appropriate caulk to fill the holes.
3. Cover the caulk with paint (if necessary).
4. If you are installing a wall rack, measure and mark the wall.
5. Press the towel rack firmly into place after applying glue to the back.

More items...

How to remove towel bar with no set screws?

How To Remove Towel Bar With No Screws

1. Twist the brackets. The brackets on this type of a towel bar are actually the end pieces that are holding the bar onto the wall.
2. Pop off bar. It shouldn’t take too much to pull the bar from the wall once these brackets are released. ...
3. Unscrew the ends. ...
4. Take it down. ...
5. Don’t try too hard. ...
6. Repair any damage. ...

How do you remove an old bathroom towel rack?

0:163:41How to remove bathroom towel bar/rack - DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipPoints is a screw in our case a teeny tiny flat head screw. You got one on each side go ahead andMorePoints is a screw in our case a teeny tiny flat head screw. You got one on each side go ahead and remove those as you loosen up and remove these screws i recommend using one hand to hold the opposite.

How do you get an old towel rack off the wall?

In the case of a towel bar that can't simply be pulled off the wall, the adhesive or mortar will need to be cut. This is most easily done using an oscillating multitool. Position the blade between the post base and the wall, and cut the adhesive or mortar away. Repeat on the second post.

How do you remove a towel rack without visible screws?

If there are no set screws in a metal towel rack, there are often metal tabs holding the end post to a wall bracket. Use a screwdriver to depress these tabs and release the towel rack. Finally, ceramic towel rack end posts are often mortared in place.

How do you remove a towel rack bracket?

1 Phillips screwdriver. With the right tool in hand, unscrew the setscrew from one of the posts to release it from the wall bracket; then keep one hand on the towel rack to prevent it from falling while you lift off the post. Set the post and rack aside; then remove the post from the other bracket.

How do you remove a ceramic towel bar without screws?

Don't try to forcefully pry the towel bar free with a chisel or scraper‚—this can damage your drywall. Instead, use a precise cutting tool, such as an oscillating multi-tool or Dremel, to cut through the adhesive at the point where the ceramic meets the wall.

How do you use a towel bar toggle bolt?

0:463:30How to Fix a Broken Towel Rack with Toggle Bolts - NO Drywall Repair!YouTubeStart of suggested clipEnd of suggested clipYou simply insert the v away from the head of the bolt. Onto the bolt. Twist it a few times. And itMoreYou simply insert the v away from the head of the bolt. Onto the bolt. Twist it a few times. And it acts as an anchor to traction against yep so when it goes in the wall it pops.

How do you replace a towel rack?

0:131:35How To Install A Replacement Towel Bar - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide it into the holder. Push it side to side to little center itself. So with the bar in placeMoreSlide it into the holder. Push it side to side to little center itself. So with the bar in place that's it you just replace the bar. And your towel bar holder with the porcelain.

How do you remove a Moen towel bar?

Disassembly: Insert a small flathead screwdriver into the opening on the base of the accessory you are removing. Pull the screwdriver away from the wall to engage the tab inside the base of the accessory. This will release the product so that you can now pull it off the wall.

How do you tighten a towel bar without set screws?

0:006:39How To Take Off Or Tighten Hand Towel Bars TP Holders ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pull it down it's got as a spring here. So you can see the spring. This one I need to tighten.MoreAnd pull it down it's got as a spring here. So you can see the spring. This one I need to tighten.

How do you remove bath towel hooks?

1:453:55How to Replace a Towel Hook that has Fallen Off - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is there and what you could do is just kind of stick. Your screwdriver right here and as youMoreIt is there and what you could do is just kind of stick. Your screwdriver right here and as you unscrew it you'll notice that a little and kind of backs out.

How to get a towel bar out of a towel bar?

Grab one of the brackets and start twisting it. Keep twisting until you feel the portion of the bar installed there pop free. You don’t have to work on the opposite end because the towel bar can already be removed.

How to remove a towel bar with no screws?

How Do You Remove a Towel Bar with No Screws? Step 1: Get Some Screwdrivers. Step 2: Loosen Up the Brackets and Remove the Towel Bar. Step 3: Remove the Brackets. Step 4A: Take Out the Pieces behind the Brackets by Hand. Step 4B: Use a Flathead Screwdriver to Remove the Pieces behind the Brackets.

Where Is the Ideal Spot for a Towel Bar?

You want the towel bar in a spot you can reach easily while your skin is wet. Keep it close to your shower or to your sink if you have one in the bathroom. Installing multiple towel bars is also worth considering if you have the space for them.

How High Should the Towel Bar Be on Your Bathroom Wall?

If all the people inside your home are adults, you can set the height at around 48 inches. That’s the standard height for towel bar placement.

Why do you need towel bars?

Towel bars help keep your towels nice and dry. They also preserve the longevity of towels and could prove useful if you ever need to change inside the bathroom. Adding them to your bathroom is a good idea.

What is a towel bar?

Written by Upgraded Home Team in Bathroom. Towel bars are helpful accessories to have inside the bathroom. That is especially true if you find trying to dry off with moist towels to be very annoying. After some time though, you may find that the towel bar’s placement inside your bathroom is not ideal.

Why do you need a screwdriver for a towel bar?

Why do you need a screwdriver when your towel bar doesn’t have any screws? Well, that’s because it does use screws, but they are just hidden from view.

How to remove masking tape from towel rack?

Place a pry bar between the holder and the wall over the masking tape. Push the top of the pry bar back to force the holder away from the wall. Follow the same process on all four sides until the ceramic towel rack holder releases.

How to protect ceramic from falling?

Lay drop cloths over the floor or tub to protect them from falling pieces of ceramic from the towel rack holders.

Can you remove a towel rack from a tile shower?

Unlike towel racks attached to brackets that are screwed into the drywall, there's no way to remove a cemented towel rack without a small amount of demolition.

Can you repair a towel rack without damaging the tile?

If it was connected to tile, there may be no need for repair if you were able to remove the towel rack holders without damaging the tile they rested on. If a tile was damaged, use the grout saw to remove the grout and break up the tile with a hammer.

How to remove a towel bar without screws?

You can remove a towel bar without screws by using a flat tool, such as a pry bar. Chances are that there is a clip mechanism fastening it to the wall, and if so, you can disengage it. Otherwise, carefully remove the towel bar with a pry bar as to not damage the wall itself.

How to remove screws from towel bar?

Using a hex key or Phillips head screwdriver, you can now remove the screws from the towel bar. Your screws are likely attached to a wall bracket, so you’ll want to support one end of the bar as you unscrew the other. Try to hold onto the bar so that you don’t damage the wall bracket when you remove the screws.

What material do you use to make a towel bar?

For example, if your towel bar is fastened to ceramic tile , you will need two-part epoxy resin. Take a look at each step and see how it applies to your towel bar in your bathroom. 1. Find the Screws.

What tools do you need to remove a towel bar?

Luckily, removing a towel bar is among the simplest tasks you can find around the house. The essential tools for the job include: Screwdriver. Drill. Hex key.

Why do you need a towel bar?

Towel bars are necessary if you have space and want your towels to dry properly. They are particularly useful when it comes to living in a family household or with multiple roommates. Drying towels with a towel bar is the best way to avoid that mildew smell that comes with leaving wet towels bunched up.

How long does it take to dry a towel bar?

The whole job won’t take longer than 20 minutes, but dry times for the drywall compound may take 24 hours. As long as you follow the steps as detailed below, you can remove your towel bar easily and without headaches. Let’s take a step-by-step look at how you can properly and safely remove your towel bar in a little time.

Where do you find the screws on a towel bar?

Find the Screws. Depending on the towel bar that you own, there may be screws fastening it to the wall. If so, you will likely find them on each end of the bar going into the wall. However, if there are no screws, then you most likely will find a clip mechanism that holds your towel bar in place.

How to pull a bar off a wall?

Use a flat tool and insert it between the bar ends and the wall. Get a good grip on this tool while inserting it between the bar end and the wall. Apply some pressure to this tool so it creates a gap between the bar and the wall making pulling the bar off easier.

Can you remove a bar with two way tape?

However, there are other ways the bar can be installed that is quite easy to remove and one such way is the two-way tape.

Can you take a bar down if you can't remember?

If you can’t remember what you used, you may have a hard time taking it down especially if it is glued to the wall.

Can towel bars be damaged?

This way your towel bar will not be damaged and neither will your tiles. But if the bar is installed on a wall, you should carefully try to get it off without damaging the paint. To remove the bar from the wall without damaging the paint, spray some thinner on the tape on the wall as it will soften the glue and make the tape easier to peel off. ...

How to smooth out a caulk joint?

Let the caulk stiffen for an hour or so and then add caulk around the perimeter. Use a wet finger or rag to smooth the caulk joint. Let it sit overnight before you pull the tape, then caulk any edges hidden by the tape. Remember to put the rod in before setting the second fixture.

How long does it take for a tile remover to work?

Let the remover work for three minutes, then scrape the residue with a plastic putty knife. Apply more remover and scrape until it’s gone. Wipe the tile with a clean rag wetted with the remover, remove the tape and call it done.

How to protect a tile fixture from scratches?

If the putty knife doesn’t hit anything hard, move on to the next step. Tape off the tile around the fixture to protect it from scratches. Then fit your oscillating tool with a flexible scraper blade and slide it under the fixture as shown.

Can you replace a plastic towel bar?

Ceramic towel-bar anchor posts rarely fail. But the plastic bar can snap, sag, develop cracks, fade or discolor as it ages and is exposed to cleaning chemicals. The original bar is one piece, and since the ends are locked into place, you can’t just slip in a new one. But you can buy spring-loaded replacements that can be cut to length and snapped into place like the bar in a toilet-paper holder. You can find universal towel-bar replacements at home centers or online stores (eclectic-ware.com is one online source).

Can you use old bar as template?

Note: Don’t use the old bar as a template (it didn’t have spring tensioners). Next, cut the bar to length ( photo 1 ): Mark the cut length on the new bar; cut the bar by hand with a hacksaw to prevent chipping; clean up the inside and outside edges with a utility knife before inserting the spring tensioners.

Can you replace a towel bar in a ceramic tile wall?

Replace old towel bars, soap dishes, corner shelves and other ceramic fixtures on ceramic tile walls without breaking the tile or cutting into the walls. Or, if the only problem is the towel bar itself (it’s missing, it’s broken, or it’s just plain ugly), just replace it with a spring-loaded one. Here are the easiest ways to rejuvenate the ceramic fixtures in your bathroom.