Remove the Old Microwave
- Step 1: Disconnect the Microwave Unplug the microwave from the outlet, which is usually in the cabinet above.
- Step 2: Remove the Support Screws
- Step 3: Pull Out the Old Microwave
- Step 4: Remove the Mounting Bracket Install the New Mounting Bracket The general steps for installing an OTR microwave oven are below. Follow the specific installation instructions for your microwave. ...
Full Answer
How to replace a built in microwave?
Install the new mounting bracket
- Take out the microwave from the box. The manufacturer usually prints instructions on the box. ...
- Remove the mounting bracket from the back of the microwave.
- In the cabinet opening, mark the studs. ...
- The built-in microwave includes a template for positioning the mounting bracket. ...
- Remove the template and drill the needed holes. ...
Can built in microwaves be repaired?
Yes, microwaves can be repaired. However, the cost to repair a part varies depending on your location, the part that needs to be replaced, and the age of your microwave. The location is based on the cost of living as well as the distance the repairman may need to travel. The magnetron is the most important and expensive part of the microwave.
How do I remove an over the range microwave?
The Drip Cap
- Removing a GE over-the-range microwave can be an easy task if it is approached with the right knowledge and tools.
- Microwave ovens can be heavy and unwieldy, and the process will require that the microwave be lifted and carried.
- Pull the ductwork up and away from the top of the microwave.
What is the best built microwave?
- BEST OVERALL: KitchenAid 1.4 cu. ft. Built-In Microwave
- BEST BANG FOR THE BUCK: Panasonic Built-In Microwave Oven
- UPGRADE PICK: Panasonic Home Chef 4-in-1 Microwave Oven
- BEST SMALL: RecPro RV Stainless-Steel Microwave
- BEST LARGE: Frigidaire Gallery 2.2 cu. ft. ...
- BEST CONVECTION: KitchenAid 1.4 cu. ft. ...
- ALSO CONSIDER: Panasonic Microwave Oven with Cyclonic Wave
Is it easy to replace a built-in microwave?
When removing built-in microwaves, finding the right replacement and careful removal is key. It might look as though your built-in microwave is installed too tightly for you to remove easily, but that's more than likely not the case. You can remove it and replace it with an upgraded version without much difficulty.
How do I get my built-in microwave out?
How to Remove a Microwave Over Range in 5 StepsUnplug your microwave. The cord is usually fed through a hole in your cabinets. ... Identify the mounting screws in your cabinet. ... Tilt the microwave to release it from the mounting bracket. ... Lift up the microwave. ... Pull the microwave out.
How do you remove a cabinet mounted microwave?
1:039:06Over The Range Microwave Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis microwave has two Phillips head bolts that secure the top of the microwave to the bottom of theMoreThis microwave has two Phillips head bolts that secure the top of the microwave to the bottom of the cabinet. So I'll take a Phillips screwdriver and twist the bolts counterclockwise to remove them.
How hard is it to replace an over the range microwave?
Replacing an over-the-range microwave is a relatively straightforward DIY home project. Microwaves are heavy, though, so it's a good idea to get someone to help you hold the microwave at certain steps during the installation. The project will require a drill, stud finder, measuring tape, and a pencil.
Do you need an electrician to install a microwave?
A licensed handyman, general contractor, electrician, or appliance installer can install a microwave. A handyman charges $100 to $300 on average to install a microwave, and home improvement stores charge $100 to $400.
How much does it cost to remove and install a microwave?
The cost of a microwave installation is around $147 for labor alone, with most installations costing between $106 and $188. However, built-in microwaves are more costly to install, ranging from $200 to $2,650. Adding an electrical outlet, venting duct, and custom cabinetry can add $500 to $2,000 to your project total.
How do you replace a wall mounted microwave?
1:079:33How To Replace a Microwave - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're gonna tilt the top of the microwave away from the cabinet pulling the cord through at theMoreYou're gonna tilt the top of the microwave away from the cabinet pulling the cord through at the same time and simply lift it off the bracket. And remove it.
How do I dismount a microwave from the wall?
2:1218:02How To Remove And Install A Microwave | Over-The-RangeYouTubeStart of suggested clipEnd of suggested clipSo just with a simple phillips head screwdriver i'll remove that left side mounting screw and thenMoreSo just with a simple phillips head screwdriver i'll remove that left side mounting screw and then move on to the right side mounting screw leaving one still in place while i get under the microwave.
How do you take down a cabinet attached to the wall?
1:032:19How to Remove Kitchen Cabinets | HGTV - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour cabinets are now being held to the wall. Using only the bottom screws locate the bottom screwsMoreYour cabinets are now being held to the wall. Using only the bottom screws locate the bottom screws on your cabinet. These are probably located on the underside. Though they may be on the inside.
Can I install an over the range microwave myself?
Installing an over-the-range microwave oven is often easier than you think. If you are simply replacing an existing vent hood or older microwave with a new oven, you can install it easily enough with common tools. You will need a helper for this one, as an extra set of hands is essential.
Is it worth repairing 5 year old microwave?
The first indicator that your microwave is better off replaced is the five-year lifespan. Microwaves can last a long time, but they have the shortest lifespan of household appliances. If your microwave is over 6 years and especially if it's approaching 10 years old, you're likely better off with a new microwave.
Do all microwaves use the same mounting bracket?
NOTE: When replacing an Over-the-Range microwave, the mounting bracket included with the new microwave should be used since the mounting bracket is specific to each model. The new screws, bolts and exhaust adapter should also be used.
How do I dismount a microwave from the wall?
2:1218:02How To Remove And Install A Microwave | Over-The-RangeYouTubeStart of suggested clipEnd of suggested clipSo just with a simple phillips head screwdriver i'll remove that left side mounting screw and thenMoreSo just with a simple phillips head screwdriver i'll remove that left side mounting screw and then move on to the right side mounting screw leaving one still in place while i get under the microwave.
Can you out microwave inside cabinet?
This is a question we hear time and time again at Sharp. And while many bloggers will advise you to install a microwave in your kitchen cabinets, we strongly advise against it. A microwave oven, designed exclusively for a kitchen countertop, has vents that are built into the back of the microwave.
How do you replace a wall mounted microwave?
1:079:33How To Replace a Microwave - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're gonna tilt the top of the microwave away from the cabinet pulling the cord through at theMoreYou're gonna tilt the top of the microwave away from the cabinet pulling the cord through at the same time and simply lift it off the bracket. And remove it.
What do you do when your built-in microwave stops working?
Start by checking the wall plug to ensure the microwave is plugged into power. Next, check the door switch and the door latch assembly. The microwave won't start if the appliance believes the door is open. Next, check the two fuses, the thermal fuse, and the ceramic fuse, to see if they need to be replaced.
Should You Remove It?
Built-in microwaves are really handy for space-saving, but there are a couple of places that are misguided for installation, especially with families. The common thinking used to be to install the microwave higher up and out of the way, but safety-first thinking has a new idea on that.
How to lower a microwave rack?
Your assistant needs to brace the underside of the microwave and hold it in place while you get up top to remove the two screws. With the screws out, the assistant can begin carefully lowering the microwave. If you're not sure what sort of mounting system is behind the microwave, just lower it carefully until it's on a 45-degree angle. Now, you should be able to see if it's a rack at the bottom or brackets on either side.
Where should the plug be on a microwave?
The plug should be at the back of the cabinet. So, unplug the microwave before you start the removal process. Your assistant needs to brace the underside of the microwave and hold it in place while you get up top to remove the two screws. With the screws out, the assistant can begin carefully lowering the microwave.
Who is the daughter of a realtor and interior decorator mother and a home contractor father?
Lowe's: Replace an Over-the-Range Microwave Oven. Steffani Cameron. Steffani Cameron is the daughter of a realtor and interior decorator mother and a home contractor father. Steffani is a professional writer with over five years' experience writing about the home for BuildDirect and Bob Vila. Raised with a mad love for decorating, Steffani gave up ...
Do you need a screw driver to remove a microwave?
Hunker may earn compensation through affiliate links in this story. You will need a screw driver when removing a microwave. Microwaves are one of those appliances that, once it's compromised or breaking down, it's probably best to replace it. Maybe you've moved into a place with an obsolete microwave installed under a cabinet or onto ...
Do you need a helper to remove screws from a microwave?
Getting Started. You really do need a helper to get this job done, as recommended by Abt, because they'll need to brace the microwave in place while you're trying to remove screws. As you wait for your assistant, you can check out the type of screwdriver needed for the job.
How much does a microwave weigh?
Microwaves can easily weigh over 50 pounds, and it's a good idea to have a helper who can assist you in lifting the microwave off the bracket and setting it down safely. Advertisement.
How to get a microwave out of the way?
Get off the step ladder and move it out of the way. With one or both arms under the microwave (and your helper ready to support the microwave as well), lift the microwave up slightly and toward you until it is no longer caught by the lip of the wall panel.
Where is the outlet on a microwave?
The outlet is typically hidden in the cabinet above the microwave. Remove any items stored in this cabinet to ensure the cord will not get caught on anything as the microwave is lowered.
Can you use a microwave over the range?
If it's just not convenient for you to use an over-the-range microwave or you'd prefer to install a range hood instead, you can remove the wall bracket and patch the holes with a bit of drywall putty. Allow the putty to dry, and then sand it smooth and paint over it.
Do you need to remove the wall bracket for a microwave?
Your new microwave will come with its own wall bracket. If your current wall bracket is the same, there's no need to remove it.
Who is Cathy Habas?
Cathy Habas enjoys distilling even the most complicated home improvement tasks into bite-sized pieces. She believes in empowering homeowners one article at a time.
Can you remove a built in microwave?
It is relatively easy to remove a built in microwave.
How to use a microwave oven for two people?
Using two or more people, align the microwave oven on the spacer bars, if applicable. Open the microwave oven door and push against the front frame of the oven to fully insert the appliance into the cabinet .
What is a Kitchenaid countertop oven?
KitchenAid® countertop toaster ovens are made to deliver powerful performance that lets you create everything from roasted chicken to your favorite cupcakes. Explore our selection to find the best fit for your home.
What voltage is needed for a 60Hz appliance?
The electrical supply for the appliance must be 240V at 60Hz. A dedicated circuit is required.
How wide is a kitchen cabinet?
Step 1: Measuring the cabinet opening. For proper installation, the cabinet opening will need to be 28 ½ inches wide, with a recommended height of 17 ⅝ inches. A minimum depth of 21 ⅞ inches is required, along with 2 and 3/16 inches of clearance above the opening and a 1 inch clearance below.
Is it dangerous to move a microwave?
WARNING: Excessive Weight Hazard. Use two or more people to move and install the microwave oven. Failure to do so can result in back or other injury. Remove any packaging materials from the microwave oven, as well as the glass tray, support and any other accessories, if applicable.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
How to remove a microwave trim?
1. Insert the tip of a putty knife under one side of the trim that surrounds the front of the microwave to a depth of one inch. Force it lightly if you have to. Tip and rock the putty knife sideways until the trim lifts up slightly.
How to get microwave out of opening?
Slide the microwave forward to your body until you can get both hands underneath it and pull it out of the opening.
Do microwaves need air?
Microwaves need adequate air space around them, but they appear to be built into the cabinets with no extra room. This illusion comes from trim pieces that are installed to the front of the cabinet after the microwave is installed. If you need to remove your microwave and replace it, or even if you want to clean behind it, ...
Can you replace trim on a microwave?
Be gentle with the trim, but if you do break it, you can easily replace it with almost any molding or trim of your choice. Some new microwave ovens even come with a trim kit. Take the opportunity to thoroughly clean inside the microwave opening. Dust accumulates behind them. Don't lift more weight than you can handle.
Who is Wade Shaddy?
Shaddy has also worked as a newspaper reporter and writer, and as a contributing writer for Bicycling Magazine.
Why are microwaves so popular?
Microwaves are a kitchen staple. They offer convenience, no residual heat from cooking and, when compared with an oven or range, efficiency. With so much going for them, it’s no surprise microwaves are so popular. If there was ever a drawback to having a microwave oven in the kitchen, it was that the appliance claimed too much valuable countertop ...
How to take the weight off a microwave?
Lift the microwave and set the bottom rear on the mounting bracket. Find the two hinges that fit into the rear slots on the microwave. This will help to take the weight off of the unit.
How to mount a microwave to the wall?
Open up the back mounting-template that came with your microwave and position it on the wall. Use the pencil to mark the available holes for mounting the bra cket to the wall.
How many amps do you need for a built in microwave?
Installing a built-in microwave is really not that difficult, but what many people don’t realize is that they need a dedicated 20- amp circuit installed in the cabinet directly above the microwave oven for the installation to be up to code.
Is there a drawback to having a microwave oven in the kitchen?
If there was ever a drawback to having a microwave oven in the kitchen, it was that the appliance claimed too much valuable countertop real estate. But ever since microwave ovens were made to be installed over the range, that dilemma has ceased to exist.
