How Do You Remove Cast-Iron Pipe Lead Joint?
- Plug the hole in the soil pipe.
- Remove a small part of the soil pipe with an angle grinder or a soil pipe cutter.
- Because the pipe usually is empty, you can cut a small section without damaging the entire stack.
- After removing this section, quickly fasten it. As the stack slides from the wall, there’s a good chance you’ll...
Is it possible to remove lead from cast iron pipe?
It is possible to remove the lead and oakum. After you have gotten all the lead out and cleaned up the hub, you can place a donut (also known as a compression joint seal) in the hub of the cast iron pipe to adapt it to PVC. (Note that donuts are only usable on non-pressurized pipes, such as waste/drain lines.)
How do you cut cast iron pipe with a drill?
The job requires a few hand tools and a cast-iron snap cutter. Install a 14/-inch drill bit into a cordless drill. Drill a series of holes, 1/2 inch apart, in the lead seal around the mouth of the over-fitting where two sections of cast-iron plumbing pipe join.
How do you get lead out of a plumbing pipe?
Now you can use a screwdriver or chisel to pry the entire ring of lead out of the pipe. (You’ll probably have to hit the inside of the hub with a good scrubbing from a Brillo pad or sandpaper, AFTER IT COOLS OFF.)
How do you convert cast iron pipe to PVC?
In this picture the cast iron pipe hub is on the left. It is possible to remove the lead and oakum. After you have gotten all the lead out and cleaned up the hub, you can place a donut (also known as a compression joint seal) in the hub of the cast iron pipe to adapt it to PVC.
How do you separate old cast iron pipe joints?
Tap the handle of the screwdriver with a hammer to drive the tip under the lead to pry it out. Pry out the oakum packing below the lead, using the screwdriver. Pull apart the connection. Repeat the procedure to disconnect other sections joined with lead and oakum.
How do you separate cast iron downpipes?
If fixed, maybe in concrete, cut it off at the bottom, ease the bottom out and in to loosen the large pins holding the brackets at the top of the pipe in. Work your way upwards. Or angle-grind the heads of the pins off, remove pipe.
How do you remove a cast iron pipe from a wall?
0:083:32How to Repair Cast Iron Drain Pipe In The Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i cut it using my milwaukee m18 fuel sawzall. And the milwaukee torch carbide blade which isMoreAnd i cut it using my milwaukee m18 fuel sawzall. And the milwaukee torch carbide blade which is designed for cutting cast. Iron. Next i just wiggled the cast iron pipe out of the wall.
Do lead drain pipes need to be replaced?
Realistically, a lead drainage line only needs to be replaced if it is leaking or damaged, but in a real estate marketing situation, all the lead pipe should be updated and removed as a selling point.
How do you loosen a stuck pipe fitting?
0:001:24Loosen Stuck Pipe Threads - With Heat! - YouTubeYouTubeStart of suggested clipEnd of suggested clipFitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apartMoreFitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apart while it's still heated. That will make it a lot easier since the fitting expands.
How do you cut cast iron pipes with an angle grinder?
2:169:40Fastest Way to Cut Cast Iron Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne is going to be the angle grinder with a metal cutoff blade and the second option is going to beMoreOne is going to be the angle grinder with a metal cutoff blade and the second option is going to be a reciprocating saw with a metal blade.
How do you replace a cast iron pipe?
0:074:04Replacing Corroded Cast Iron Sewer Pipes with ABS Plastic - YouTubeYouTubeStart of suggested clipEnd of suggested clipHe tried as herself you need good plates and you'll still go through a few for a larger. Project.MoreHe tried as herself you need good plates and you'll still go through a few for a larger. Project. Next I cut the ABS on the sides of the cast iron using a hacksaw. Which is like a mini reciprocating.
Do cast iron pipes need to be replaced?
Wear and tear is normal in residential pipe systems. One frequently asked question is “How long do cast iron drain pipes last?” Cast iron waste pipes last anywhere between 50 and 100 years. However, it may be time to replace cast iron pipes long before their lifetime is up.
How to remove oakum from lead?
Pry out the oakum packing below the lead, using the screwdriver. Pull apart the connection. Repeat the procedure to disconnect other sections joined with lead and oakum.
How to protect your face from a cast iron pipe?
To protect your face, turn your head to one side when snap-cutting the pipe. Do not attempt to take apart cast-iron plumbing pipe that is still installed unless you are skilled in such tasks. William Machin began work in construction at the age of 15, while still in high school.
What is William Machin's hobbies?
His hobbies include horses, motorcycles, road racing and sport fishing. He studied architecture at Taft Junior College.
Tips
Using PVC with 'No-Hub' clamps is a LOT cheaper and easier method than the above-described type of repair.
About This Article
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 11 people, some anonymous, worked to edit and improve it over time. This article has been viewed 50,478 times.
