Unplug the Maytag clothes dryer from the power source. Remove the two screws on the front panel. You will find them approximately 4 inches from the bottom, under the beveled edge. Pull the bottom of the front panel toward you until the clips on the top of the panel release. Carefully disengage the wires from the door switch and set the door aside.
How to test if dryer door switch is faulty?
What to do if dryer is gas?
About this website
How do you remove a Maytag dryer switch?
0:261:33How to Replace a Maytag Electric Dryer Push-to-Start Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you know how to correctly reconnect them later then remove the wires release the locking tab andMoreSo you know how to correctly reconnect them later then remove the wires release the locking tab and slowly rotate the push-to-start switch. While pulling it to release it from the control panel push.
How do you change a door switch on a Maytag Bravos dryer?
0:483:19Maytag Dryer Door Switch Replacement #W10169313YouTubeStart of suggested clipEnd of suggested clipPull the panel out from the bottom to detach. Note the orientation of the door switch wires thenMorePull the panel out from the bottom to detach. Note the orientation of the door switch wires then disconnect. Them open the dryer door and depress the retaining tabs to release the old door switch.
How do you check a Maytag dryer door switch?
1:141:56Dryer Won't Start? Two Terminal Switch Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou begin make sure the switch you're testing has been removed or isolated from the appliance use aMoreYou begin make sure the switch you're testing has been removed or isolated from the appliance use a probe to touch one of the switches terminals and the second probe to touch the other terminal.
Can a dryer run without a door switch?
It is a safety switch designed to prevent the drum from turning while the door is open. If the switch were removed and the circuit closed by connecting the wires the drum will turn and the dryer will work.
Why will my Maytag dryer not start?
If your dryer won't turn on but seems to be properly connected to a power supply, check to make sure your home isn't experiencing any power outages, blown fuses or tripped circuit breakers. Before attempting a dryer cycle, make sure all fuses are intact and tight.
Can you reverse the door on a Maytag dryer?
Most Maytag dryers come with the option to reverse the door swing direction, making the appliance easier to access in a wider range of locations. You might want to make the door open in the opposite direction if it strikes cabinets or other nearby appliances in its current position.
What happens if dryer door switch is broken?
Faulty Switch As a safety feature, the dryer will not work with an open door. When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
How do you test a dryer door switch?
0:201:33Dryer Not Starting - How to Test the Door Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would want to first check the the door switch let me show you how all right so on the doorMoreYou would want to first check the the door switch let me show you how all right so on the door switch we have three connections and the first connection is going to be the common. Then we have a
When I push the start button on my dryer nothing happens?
If the dryer still doesn't start, there are several possible reasons, from a door switch that's not recognizing that the door is closed to a failure in the main electronic control board. A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting.
How do you remove a dryer door switch?
0:261:30How to Replace a Whirlpool Electric Dryer Door Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a slot screwdriver to release the locking tab on the wire harness plug for the door switchMoreUse a slot screwdriver to release the locking tab on the wire harness plug for the door switch remove the mounting screws from the existing door switch. Pull the door switch out of the dryer.
Why is my dryer turning on when I close the door?
Push Start Button Relay Stuck. Another issue which may cause dryer to keep running is when push start button is stuck. It always sends the power to the dryer motor right after you close the door, causing dryer works non stop.
Why does my dryer keep running when I open the door?
If an electric or gas-heated clothes dryer continues to run after the door is open, the door safety switch is stuck in the closed position. To replace the switch, Part Select says to release the catches holding the dryer top down by slipping a knife between the top and front panel or removing a single screw.
How do you replace a lid switch on a Maytag washer?
0:533:43Maytag Washer Repair - How to Replace the Lid Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe'll just lift up slightly on the back of that control panel unhook the feet on the front. Then we'MoreWe'll just lift up slightly on the back of that control panel unhook the feet on the front. Then we're just gonna let that hanging down over the back of washer.
How do I fix the latch on my Maytag dishwasher?
0:182:05Maytag Dishwasher Door Latch Replacement #99002254 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore you begin be sure you turn off the power supply to your dishwasher. Your first step is toMoreBefore you begin be sure you turn off the power supply to your dishwasher. Your first step is to remove the screws to release the inner door panel. Next squeeze the tabs to release the control shield.
Troubleshooting a Dryer Door Switch | Home Guides | SF Gate
Troubleshooting a Dryer Door Switch. Often, the time you find out that a dryer won't start is when you have a large, soaking wet pile of clothes that needs drying. If the contact switch in the ...
How to replace a dryer's door switch | Dryer Repair - PartSelect
Locate and replace the simple on/off dryer door switch with step by step instructions. Learn how to safely remove the wiring and old door switch mechanism and pop the new one in with this easy guide from Partselect.com
How to test a dryer's door switch | Dryer Repair - PartSelect
Safely test your dryer's door switch for functionality. Locating and testing your simple on/off dryer door mechanism with an ohmmeter is a simple task; made easier with these step by step instructions from Partselect.com.
Step 1
Unplug the Maytag clothes dryer from the power source. Remove the two screws on the front panel. You will find them approximately 4 inches from the bottom, under the beveled edge.
Step 2
Pull the bottom of the front panel toward you until the clips on the top of the panel release.
Step 3
Carefully disengage the wires from the door switch and set the door aside.
Step 1
Unplug the Maytag clothes dryer from the power source. Remove the four screws. You will find one in the hinge on the upper right, one in the hinge on the lower right and one opposite each hinge.
Step 2
Lift the door slightly and pull back. The door and the hinges will disengage. Put the door aside.
Step 3
The front panel of the Maytag clothes dryer is shaped like a goal post. Grasp the skinny, upper sides and wiggle them back and forth to unclip the panel. Pull the skinny ends of the front panel toward you, lifting it off the bottom clips. Set the front panel aside.
Where is the door switch on a dryer?
Locate your dryer's door switch. It will be located around the door opening in the front panel. You may be able to pop the switch out of place, or remove it by removing only a single screw. If you are unable to remove your dryer's door switch this way, you will have to remove the front panel of your dryer. See our section How to open up your dryer ...
What is a door switch?
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. Dryer door switches are a little over an inch long. Many are white in color and all have metal prongs, called terminals, extending out from the body of the switch.
How many terminals does a door switch have?
Some door switches have only two metal prongs extending from the body, while others have three. Those with three terminals will have a common (COM) terminal, a normally closed (N.C.) terminal, and a normally open (N.O.) terminal. Those switches with only two terminals will have either a common terminal and a normally open terminal, or a common terminal and a normally closed terminal.
How to test if dryer door switch is faulty?
If the door switch fails, the dryer won't start when the door is closed. To quickly test the door switch, open the dryer door and press the door switch lever. If the dryer drum light stays on, the door switch is faulty. Replace the door switch with the manufacturer-approved dryer part.
What to do if dryer is gas?
If it's a gas dryer, turn on the gas supply to the dryer. Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions.
