The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time. To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
Full Answer
How do I Fix my Frigidaire front load washer error code?
Frigidaire front load washer error codes, that will give you a chance to solve any issue with your front-loading model. Make sure that the water supply faucets behind the washer are fully open. Check the fill lines for freezing in the winter. Check the drain system for a siphon problem.
What do Frigidaire affinity washer error codes mean?
Frigidaire Affinity washer error codes, that are common for Affinity models; Frigidaire front load washer error codes, that will give you a chance to solve any issue with your front-loading model.
How do I fix the error code on my Whirlpool washer?
This error code is for washers with a digital display only. Unplug the washer. Check the resistance through the temperature sensor circuit. It should be around 50,000 ohms at room temperature. If the sensor is defective, replace the water inlet valve assembly. If the resistance in that circuit's sound, replace the control board.
What does error code E11 mean on a Frigidaire washing machine?
If you are getting the Frigidaire washing machine error code E11, it indicates that the washer is spending too much time trying to fill. Here are the things that could cause this issue…
How do you reset the code on a Frigidaire washing machine?
How to Reset the Settings on a Frigidaire Front WasherVerify that your Frigidaire front washer is plugged into a working electrical outlet and turned on; otherwise, you won't be able to reset it. ... Press and hold the "Spin Speed" and "Soil Level" buttons together for a few seconds.More items...
How do you put a Frigidaire washer in diagnostic mode?
0:525:56Frigidaire, Electrolux Washer - Using Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo press the soak. Extra rinse and power at the same time. Wait for it to start blinking. Now pressMoreSo press the soak. Extra rinse and power at the same time. Wait for it to start blinking. Now press the soil button you only have so long to press it you hear the door lock.
Why does my washer keep saying error?
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
What does E1 mean on a Frigidaire washing machine?
How it fails: The E1 error code on your Frigidaire washer means that the appliance is taking far too long to fill with the water it needs to start a new wash cycle. One common reason behind this is that the water tap supplying the washer isn't open all the way.
Where is the error code on a Frigidaire washer?
the failure code will appear in the display as an E followed by two numbers, a number and a letter or two letters....How to retrieve the error codes in a Frigidaire Affinity front...Wake the washer by pressing any button.Wait 5 seconds.Press and HOLD the Start/Pause and Cancel buttons simultaneously.
How do I fix E2 error on my Frigidaire washing machine?
How To Clear The E2 Code On Your Frigidaire Washer? The E2 error code on your Frigidaire washer will clear once you've restored the washer's ability to drain water quickly. You can then perform a washer reset to clear the E2 and any other error code that's currently active.
How do I reset my washing machine?
1:023:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
How do I clear E1 F9 code?
How to Fix Whirlpool Washer E1/F9 Error CodesTry a Reset. Sometimes an error code is caused by a control board glitch, where resetting the washer is all it takes to resolve the error code. ... Check your Detergent. ... Check the Drain Hose. ... Clean the Filter. ... Check the Drain Pump. ... Check the Wiring.
How do I fix E1 error on my washing machine?
Possible SolutionsCheck that the water faucets are not closed.Check that the water pressure in the house is over 20 kPa.Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.Check that the drain hose is not below 27½" (700 mm) from the floor.
How do I fix error code E1 F3?
F3 E1 Error Code Power unit down by turning off the circuit breaker or unplugging for one (1) minute. Power unit up by reconnecting power. Restart a new cycle. Monitor the washer for one (1) minute to ensure the error code does not display again.
What does E1 and F9 mean on a washer?
May 4, 2022. A Whirlpool washer error code E1/F9 occurs when the washer's control board detects that the washer cannot drain. Therefore, to resolve the E1/F9 error code, the washer components responsible for draining will need to be checked and possibly replaced.
What does E1 F3 mean on a washer?
The F3 E1 alert indicates the washer can't detect the water level. There may be an issue with the appliance control unit or associated wiring. Shut off water valves to the washer, and call for service.
How do I troubleshoot my Frigidaire Affinity washer?
How to Troubleshoot a Frigidaire Affinity WasherStop the washing machine if rattling or clanking sounds occur. ... Plug the power cord in and check household fuses or breakers. ... Add more clothing to small loads. ... Check the water pressure at a nearby faucet.
Why is my Frigidaire washer not draining?
If the washer won't drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
Why is my Frigidaire washer not working?
Ensure the power cord fits tightly in the wall outlet and you are getting power to your washer. If no power, check to ensure a house fuse isn't blown or the circuit breaker tripped. Your Frigidaire Laundry Center should be on its own circuit breaker and not shared with other outlets or appliances.
How do you put an Electrolux washer in diagnostic mode?
0:004:01Electrolux Washing Machine Diagnostics Menu Time ManagerYouTubeStart of suggested clipEnd of suggested clipTo enter the diagnostics mode turn on the machine and make sure the first cycle light is selectedMoreTo enter the diagnostics mode turn on the machine and make sure the first cycle light is selected press and hold start button and the button above the start button for a few seconds until the lights
What The E21 Code Means On A Frigidaire Washer
When your Frigidaire washing machine displays the E21 error code, that means the appliance is not draining water fast enough.
Possible Causes And Solutions
The most likely reasons for slow draining in your Frigidaire washer is a clogged drain hose, a faulty drain pump, or a failed main control board. Let’s look at each of these components, how they become problematic, and what you can do to fix them.
How To Clear The E21 Code On Your Frigidaire Washer
Clearing the E21 error code requires you to resolve the root cause of the issue. You can do so by following the troubleshooting steps detailed above.
How To Test Your Frigidaire Washer After Fixing It
Once you’ve fixed your Frigidaire washer, you can test it by running a complete wash program from start to finish. Since the E21 error code is related to the washer’s draining function, you’ll want to pay attention towards the end of the program to ensure the washer drains without any problems.