- 1. Support the front of the bike. Remove the front wheel, brake caliper and fender. Unbolt the headlamp shell from the locating ears. ...
- 2. Lift the fork leg enough to expose the top of the spring. ...
- 3. Loosen the pinch bolt on the lower steering yoke. ...
- 4. The top of the fork tube is a taper fit to the upper yoke. ...
What is a fork on a motorcycle?
The “fork” is the suspension at the front of a motorcycle. In nearly every motorcycle available today, the front wheel is held on by an axle that’s connected to the fork. It’s called a fork because it has two prongs that go around each side of the wheel.
How do you change fork oil on a motorcycle?
Every motorcycle varies in how it’s put together. But generally, the process for changing the fork oil and seals is like this: Loosen the brake calipers, top of the forks, and the clip-ons (if you have them)
How do you change the forks on a Honda Accord?
Steps Remove the front wheel. Remove the fork cap and/or plug. Measure the height of the forks. Remove the forks. Do a preliminary clean. Unscrew the damping rod bolt. Do a final clean. Install the damping rod. Pour new oil. Re-install the forks. Replace the components.
How do you clean the inside of a fork?
With the bottom bolt removed, spray some more degreaser inside the fork and pump them up and down. Let the degreaser sit and then cleanse with water. Leave the forks to dry. Give the springs, spacers and damping rod a spray with degreaser followed by a rinse of water too.
What is a fork on a motorcycle?
The “fork” is the suspension at the front of a motorcycle. In nearly every motorcycle available today, the front wheel is held on by an axle that’s connected to the fork. It’s called a fork because it has two prongs that go around each side of the wheel. Where the forks of a motorcycle are.
How do you change the fork oil and fork seals?
Every motorcycle varies in how it’s put together. But generally, the process for changing the fork oil and seals is like this:
What does motorcycle fork oil do?
The job of motorcycle fork oil is to make the motorcycle stop bouncing around after the spring compresses then rebounds.
What is the best fork oil to use?
Check your manual for your fork oil. It varies between motorcycles. You have to know a) what fork oil to use and b) how much to use.
What causes fork seals to fail?
This is something I discovered when changing my own fork oil and seals. The primary reason fork seals can fail is pitted forks.
What do you need to change fork oil?
Before starting your fork oil change, there are some tools and consumables you should get.
What is the difference between a motorcycle fork and an upside down fork?
The main difference between conventional motorcycle forks and upside-down forks is in “unsprung mass”. The unsprung mass is the word used to describe the weight of everything under the suspension spring — i.e. the wheels, brakes, tyres, and the bottom half of the suspension fork.
How do you adjust the front forks on a motorcycle?
Set sag on front forks To measure this, put the bike in a chock or have a mate hold it steady. Use a cable-tie, compress the forks, let them settle and push the cable tie up to the outer dust seal. Get off, and take the weight off the front so the forks are fully extended. The sag is the distance it’s travelled.
How do you straighten a fork stanchion?
Put a dial indicator on the tube close to the ram, put a block under the ram and come down with the press until fork bends opposite the same amount as the bend. Let it off and see where you are. If it didn’t move, double the movement on the next round. If it did move, repeat until you get it straight as you need.
How do you raise the front of a motorcycle?
Raising front suspension is achieved by pulling out the fork legs from upper triple clamps. This results in increase in castor angle, higher trail ratio, slight increase in wheel base, higher seat height & higher center of gravity.
How do you speed up the rebound on a fork?
Starting with the forks, turn the rebound adjuster clockwise all the way to the stiffest (aka slowest) position, being careful not to over-tighten the adjuster. The adjuster should only sit lightly in the seat when fully stiff, so turn it slowly, stopping as soon as you reach the end of adjustment.
How can I make my dirt bike taller?
Can You Raise The Seat Height On A Dirt Bike? Installing a taller seat or seat foam is an easy and very effective way to raise the seat and overall height of your bike. Your legs will thank you in the long run because they are less cramped.
How to adjust dirt bike suspension?
One way to adjust your dirt bike suspension is to raise or lower your fork in the triple clamp.
How to tell if a fork tube is bent?
To see if the tube is bent, you can remove the front wheel, then turn the tube in the clamps and watch for the bottom end of the fork to move around. Or, since you’ve gone that far, take the fork all the way off, put the axle end in a vise, and turn the stanchion.
How to clean a fork?
Do a preliminary clean. Pouring out the fork oil will still leave plenty of oil left inside. Get a degreaser and spray liberally inside the fork. Make sure you pump the forks up and down to get the degreaser to mix through both the inner and outer fork. Leave the degreaser in for a few minutes and then clean them out with water.
How to remove damping rod from fork?
You can skip this step if you want but you won’t get as much of the old fork oil out if you do. The location of the bolt is generally awkward so you might need to get creative to get enough leverage to loosen it. Another problem can be that the damping rod itself rotates while you’re trying to unscrew the bolt. If you find that this is the case, compress the fork and using the spring you just removed, put it back in.
How to stop a damping rod from rotating?
Put some threadlock on the bolt that holds the damping rod in place and screw it in. Just like when removing the damping rod, compress the fork and with the spring, hold the damping rod in place to prevent it from rotating . ...
How to measure forks for a bike?
Measure the height of the forks. The exact position that your forks sit in your triple tree determines the front end geometry of your bike so it’s important to that you measure this. Otherwise your bike’s handling could be vastly different upon re-installation. Using a ruler, measure how far up the fork extends above the triple tree (if at all). You’ll usually find there’s a mark on the top of the triple tree – measure from here as the height the fork is above the triple tree will vary depending on where you take the measurement.
How to get damping rods to work?
If this doesn’t work, a piece of dowel (or other appropriately shaped and long enough object) pushed into the top of the da mping rod can also work.
How to get air out of a fork?
Ensure the fork is standing vertically on a level surface. Pour in the amount of oil recommended by the manufacturer. Before putting it all in, pump the forks up and down to circulate the oil throughout and remove any air trapped.
How to fix a bike that has a front axle bolt?
1. Remove the front wheel. Follow your bike’ s instructions on how to do this. As a general rule, you’ll need to either chock the front wheel or at least have the front brake engaged to when breaking the front axle bolt loose. Once that’s loose, you’ll need to jack the front up. There are two ways to do that.
