To remove the impeller you will twist the impeller off in a counter clockwise motion. However, the impeller cannot be freed from the motor shaft without first securing the motor shaft. Move to the other end of the motor shaft in the back of the motor assembly. Take off the two screws that hold the back cover onto the assembly.
How to remove a pool pump impeller?
Then, look in the back of the motor housing for the nut that is in the back of the impeller. It is what is holding the impeller to the motor. You will need to use pliers to hold the nut in place while you use a screwdriver to loosen and remove the screw from the front of the impeller. Then, you will be able to remove the pool pump impeller.
How do you open the impeller on a Kenmore washing machine?
Although you can access the front of the impeller by removing the pump basket assembly, you cannot reach the nut on the other end of the screw that holds the impeller in place. In order to access the nut, you must enter through the back of the pump motor housing.
What causes a pool pump impeller to crack?
Sometimes debris will get into the pump and will crack the impeller. In other cases the threads that hold the impeller to the motor shaft become worn causing the impeller to wobble and rub against the diffuser. This guide explains how to replace a bad pool pump impeller. If playback doesn't begin shortly, try restarting your device.
How do you remove the impeller on a power steering pump?
Hold the nut in place with the pliers and unscrew the impeller. Depending on how long the impeller has been in place, it may take a bit of pressure to remove the screw while holding the nut in place. Once you remove the screw, you can remove the impeller.
.png?format=jpg&scale=both&mode=pad&anchor=middlecenter&width=300&height=250)
How do you remove a stubborn impeller?
0:486:42How To Remove Stubborn Impellers - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would use something called a strap wrench. Yeah you can take a strap wrench. And you can tryMoreYou would use something called a strap wrench. Yeah you can take a strap wrench. And you can try that with your Peller you could wrap that around like that on the tip of your teller.
How do you take apart a century pool motor?
4:3413:35How to Replace a Pool Pump Motor -The Ultimate Video Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's four hex nuts that hold the motor onto the housing. You have to come out sometimes they're aMoreThere's four hex nuts that hold the motor onto the housing. You have to come out sometimes they're a little difficult you'll see me taking this out in the next part of the video.
How do you remove a water pump impeller?
1:355:12How To Change your Water Pump Impeller - PowerBoat TV - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo remove the pump housing first remove the four bolts in a cross pattern to avoid warping theMoreTo remove the pump housing first remove the four bolts in a cross pattern to avoid warping the housing. Then carefully slide the rubber seal up and off the shaft.
Can you change an impeller in a pool pump?
One of the most common problems with impellers is debris in the pump, and depending on what kind of debris it is, it can crack or break the impeller. In this case, when the rest of the pump is good, you just want to replace that part.
How do I take apart my pool pump motor?
4:1111:08How to pull apart a Swimming pool Pump. What's Inside? I ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo good to have that out of the way. This is the baffle plate. And that needs to come out that'sMoreSo good to have that out of the way. This is the baffle plate. And that needs to come out that's just a press fit we just need to flex that until that comes out and yeah is the impeller. So this parts
How do you separate a pool pump from the motor?
0:148:41How to: Replace a Pool Pump Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo take off the bonding wire simply unscrew the lug and pull the wires. The first step to remove theMoreTo take off the bonding wire simply unscrew the lug and pull the wires. The first step to remove the motor from the housing is to unscrew the lid.
How do you remove the impeller from a shaft?
0:2711:11Removing a seized impeller from a Reeflo pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you cannot get it off then what you're going to want to do is you're going to actually want toMoreAnd you cannot get it off then what you're going to want to do is you're going to actually want to cut the impeller off the impellers are about $30.
How do you change the impeller?
0:335:03How to: Replace a burnt-out impeller - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the impeller pump itself is above the waterline. I don't have a danger of flooding. If. I didMoreSo the impeller pump itself is above the waterline. I don't have a danger of flooding. If. I did have a danger I'd have to take the pipe off the bottom of the pump. And plug it with a wooden bug. If.
How do you open a pump impeller?
0:212:08SMP Centrifugal Pump Open Impeller Wrench - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can now remove the impeller wrench using the knurled section of the socket. You can loosen theMoreYou can now remove the impeller wrench using the knurled section of the socket. You can loosen the impeller safely until you can remove it from the pump shaft.
How do I know if my pool pump impeller is bad?
What are the symptoms of a clogged impeller? If your pool pump impeller is clogged, it's probably making some unpleasant noises (a low, grinding sound). If you look at your filter pressure, it's likely only half of what it normally reads and the water in your pump is moving slowly or making a swirling motion.
How do you find the impeller on a pool pump?
0:392:19How To: Clean Out A Pool Pump Impeller - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll need to unscrew the pump lid and remove the strainer basket. Next using a pair of pliers.MoreYou'll need to unscrew the pump lid and remove the strainer basket. Next using a pair of pliers. Make a small 1/2 inch to 3/4 inch hook at the end of a metal coat hanger.
Where is the impeller on a pool pump?
A pump impeller sits behind the pump basket in the part of the pool pump called the Volute (aka Impeller Housing). The pump basket is in place to prevent small debris from entering the volute, and possibly clogging the impeller.
How do you disassemble a pump?
These are the steps to follow:Disconnect the electrical wires entering the electric motor cover.Disconnect the circuit pump.Remove the screws (1)Uncouple the pump unit (2) and o-ring (13)Unscrew the caps (3), making sure you secure the impeller using a soft belt, so as not to damage the paddles.More items...•
How do you repair a pool pump?
0:005:42DIY Swimming Pool Pump Repair. Save yourself a fortune! Certikin ...YouTubeStart of suggested clipEnd of suggested clipVery important before that we must make sure that we've disconnected e electrically so that there'sMoreVery important before that we must make sure that we've disconnected e electrically so that there's no chance of getting an electric shock when we're removing the mortar.
How do you fix a cracked pool pump?
For a leak at the male threaded adapter, roll the putty into a thin snake and press it into the fitting before threading the parts back together. Repair cracks in the pump housing by pressing putty into the crack a little at a time, building up several layers. Allow a small amount of putty to overflow the cracked area.
How do you reassemble a pool pump?
2:538:10Pool pump housing disassembly and reassembly - changing the sealYouTubeStart of suggested clipEnd of suggested clipAnd what you do is you put the faceplate up like so and then we align this to ten o'clock and you'llMoreAnd what you do is you put the faceplate up like so and then we align this to ten o'clock and you'll see that the screw lines up the screws. Now.
Where is the impeller located on a pool pump?
The impeller is located right behind the pump basket, so you have to remove the basket to access the impeller. Remove the pump filter assembly by removing a series of bolts located around the circumference of the pool pump using a ratchet set.
How to remove a screw from an impeller?
Hold the nut in place with the pliers and unscrew the impeller. Depending on how long the impeller has been in place, it may take a bit of pressure to remove the screw while holding the nut in place. Once you remove the screw, you can remove the impeller.
What do you need to keep a pool clean?
Things You'll Need. Pliers/ratchet set. Screwdriver. The impeller is the heart of a pool filter. When it comes to maintaining a clean pool, you must have a properly functioning pool filter in addition to the right mix of chemicals. If the pool filter stops working, it is impossible to keep the pool clean. The impeller is the heart of the pool ...
What happens if your pool filter stops working?
If the pool filter stops working, it is impossible to keep the pool clean. The impeller is the heart of the pool filtration system. It creates the suction that draws the water from the pool into the filter. If it becomes defective, you must repair or replace it. Advertisement.
Can you remove the impeller on a pool pump?
Unless you’re comfortable working with motors, you should have a pool professional remove the impeller. Although you can access the front of the impeller by removing the pump basket assembly, you cannot reach the nut on the other end of the screw that holds the impeller in place. In order to access the nut, you must enter through the back ...
What is the purpose of the impeller?
As I mentioned above, an impeller is the heart of a pool pump assembly. What does it do? Well, the component is designed to rotate and create centrifugal force that transfers energy from the motor. The effect created adds kinetic energy to the flowing water allowing it to go for a further distance.
What happens when the impeller goes bad?
Before you decide to remove the pool pump impeller, you need to have a reason for it, with the main reason being it is faulty. But how did you know it’s defective. An impeller goes bad if it gets clogged or it’s worn out.
How long does a pool pump impeller last?
A right quality pump has durable components, including the impeller. However, as a moving part of the water pump, it will need replacement at one time. The lifespan of a good quality impeller is between 8 to 15 years, depending on the pump’s usage.
How Do You Remove Pool Pump Impeller
When it comes to removing the pool pump impeller, you must understand that this is a simple process that needs care. If you want to maintain a clean pool, it’s best to ensure your pool circulation and filtration system works perfectly. If the pool pump stops working, it becomes tough and nearly impossible to keep your pool clean.
How to remove impeller from pump?
The first step in preparing to remove your pump's impeller is to turn off all power to the motor. For maximum safety turn off the power at the circuit breaker to the motor - usually located next to the timer box.
Can you put a shaft seal upside down?
It is possible to place this seal upside down. Note: You may have to also have to remove the metal collar if the new shaft seal also has one. Several people have written in saying that the new seal won't fit because they were trying to place the new collar on top of the old one.
