Step by Step How to Remove Impeller From Water Pump
- 1. Turn Off the Power to the Pump. The first step is to turn off the power to the pump. ...
- 2. Drain the Pump. ...
- 3. Remove the Pump Cover. ...
- 4. Locate the Impeller. ...
- 5. Remove the Impeller. ...
- 6. Use an Impeller Removal Tool. ...
- 7. Use a Screwdriver. ...
- 8. Clean the Pump Housing.
How do you get a stuck impeller out of a hot tub?
0:285:36Removing a Stuck Impeller on a Hot Tub Pump How To Spa GuyYouTubeStart of suggested clipEnd of suggested clipBut what you do is take a flat screwdriver. It's got a flat screwdriver fitting in there turn. It upMoreBut what you do is take a flat screwdriver. It's got a flat screwdriver fitting in there turn. It up so you can see it. And you hold the flat screwdriver side. And grab the impeller.
How do you remove a pump impeller?
2:024:23Inyopools.com - How to replace a pool pump impeller - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the impeller counterclockwise to loosen it up. Keep on screwing the impeller until you actuallyMoreTurn the impeller counterclockwise to loosen it up. Keep on screwing the impeller until you actually get the impeller off the shaft.
How do you remove an impeller shaft?
1:075:07How to Change the Impeller and Shaft Seal on the WLS - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a flathead screwdriver pop. Off the center rubber cap revealing a small crevice wide enough toMoreUsing a flathead screwdriver pop. Off the center rubber cap revealing a small crevice wide enough to be held still with the flat-head screwdriver to prevent it from turning lock.
How do you remove a stubborn impeller?
0:486:42How To Remove Stubborn Impellers - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would use something called a strap wrench. Yeah you can take a strap wrench. And you can tryMoreYou would use something called a strap wrench. Yeah you can take a strap wrench. And you can try that with your Peller you could wrap that around like that on the tip of your teller.
How do you change a water pump impeller?
1:355:12How To Change your Water Pump Impeller - PowerBoat TV - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo remove the pump housing first remove the four bolts in a cross pattern to avoid warping theMoreTo remove the pump housing first remove the four bolts in a cross pattern to avoid warping the housing. Then carefully slide the rubber seal up and off the shaft.
How do you open a pump impeller?
0:082:08SMP Centrifugal Pump Open Impeller Wrench - YouTubeYouTubeStart of suggested clipEnd of suggested clipSelect the correct size input shaft socket from your kit next to each socket there is a proper sizeMoreSelect the correct size input shaft socket from your kit next to each socket there is a proper size key to match the pump. Size place the key on the drive end of the shaft.
What is impeller puller?
Impeller pullers are also known as impeller removal tools or impeller extractors. Replacing an impeller is easy. By removing the end cover screws, it is possible to remove the impeller by using an impeller puller or impeller removal tool even in confined spaces.
How do you free a stuck pool pump impeller?
You can use a bent coat hanger or just your fingers to reach into the impeller. Insert the wire (or fingers) into the opening leading into the impeller until it stops. Use a swirling motion to dislodge debris. Pull out anything you find and clean your hook now and again.
How do I know if my impeller is clogged?
If your pool pump impeller is clogged, it's probably making some unpleasant noises (a low, grinding sound). If you look at your filter pressure, it's likely only half of what it normally reads and the water in your pump is moving slowly or making a swirling motion.
What most commonly damages pump impellers the most?
The top 3 most common causes for impeller failures are due to cavitation, erosion and corrosion.Cavitation. Cavitation is a great danger for any centrifugal pump is cavitation. ... Erosion. ... Corrosion.
Are pump impellers reverse thread?
The reverse thread of the impeller tightens the impeller as the motor turns. If this is the case, first, remove the impeller screw by turning clockwise. If you're having problems removing the screw, inspect for corrosion or calcium buildup. A heavily corroded impeller screw can make it difficult to remove.
How can we remove impeller from centrifugal pump?
0:412:24SMP Centrifugal Pump Impeller Wrench (Closed) - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply either a one inch combination wrench or crescent wrench to the squared head of the impeller.MoreApply either a one inch combination wrench or crescent wrench to the squared head of the impeller.
How to install an impeller?
Installing an impeller involves holding the pump shaft from the motor end with a flat screwdriver or tool while hand-threading on the impeller to the shaft. If the old impeller will not unthread, techs may use large Channel locks or pliers to get the old impeller off of the pump motor shaft by rotating it counter-clockwise.
Can you replace an impeller in a waterway?
Impellers can be replaced in select AquaFlo, Waterway, Balboa, Hayward, Pentair, Vico, Jacuzzi, Watkins, Laing,Acura and other pump wet end models. Once the old impeller has been removed, the tech will inspect the motor shaft for straightness and also to remove any built up rust or debris.
Can you replace an impeller shaft seal kit?
It is highly recommended to change out the shaft seal kit when replacing the impeller. Pump impeller blades can be sharp, so this type of work is best performed by spa technicians or skilled DIY individuals. In any case, pump work should not be performed on the spa pump if power is connected to the pump. Always disconnect power and turn off spa before performing this type of electrical work.
Which way do you turn an impeller?
Typically impellers are installed counter-clockwise - same way the shaft spins. To remove impeller, turn it clockwise.
Can you replace a wet end?
Sometimes it is better to replace the complete wet end, but the individual parts such as seal kit, impeller and orings are usually readily available for most current models and brands.