Straighten a large, heavy-duty paper clip. Insert the paper clip into the damaged tombstone next to one of the two tombstone wires. The paper clip opens the tension spring connector inside the tombstone and allows you to pull out the wire. Repeat this for the remaining wire attached to the tombstone.
How do you replace a broken tombstone wire?
Insert the paper clip into the damaged tombstone next to one of the two tombstone wires. The paper clip opens the tension spring connector inside the tombstone and allows you to pull out the wire. Repeat this for the remaining wire attached to the tombstone. Insert the paper clip into the wire hole on the replacement tombstone.
How do you replace a fluorescent light on a tombstone?
The paper clip opens the tension spring connector inside the tombstone and allows you to pull out the wire. Repeat this for the remaining wire attached to the tombstone. Insert the paper clip into the wire hole on the replacement tombstone. Push the fluorescent fixture wire into the tombstone next to the paper clip.
How do you fix a broken tombstone on a tree?
Look at how the damaged tombstone attaches to the end of the fixture. Some tombstones attach to the fixture with a screw, while others snap into notches cut into the metal on the fixture. Remove the screw or pull the damaged tombstone from the end of the fixture.
How do you clean a marble headstone with ammonia?
If the headstone you are cleaning is made from marble or limestone, add one tablespoon of ammonia to the non-ionic soap water mixture. Use only a soft bristled brush such as an automotive detailing brush or a soft toothbrush. When scrubbing the tombstone, always move in an orbit motion randomly all over the stone.
How do you remove wire from a lampholder?
Almost all lamp holders have holes that are key shaped, or oval-ish. You take the paperclip, and straighten out a bend or two so you have a nice, straight piece of metal to work with. Now push the paperclip into the smaller part of the hold (indicated by the arrow above) deep enough that the wire is released.
How do you remove ballast wires?
Remove the Cover Plate Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.
How do you remove wires from a push in connector?
0:252:40IDEAL In-Sure Push-In Wire Connectors HOW TO REMOVE WIREYouTubeStart of suggested clipEnd of suggested clipPull away from the connector and will go back and forth and it will come out again make sure theMorePull away from the connector and will go back and forth and it will come out again make sure the power is off I'm going to attempt to do. This I've got it on the tripod.
How do you remove wires from fluorescent sockets?
Grasp the wire and twist it (rotate) while gently pulling on the wire until it comes out. If not done properly, the wire could break off before it becomes unseated from the connector. Fluorescent lampholders hold fluorescent tubes in place on a light fixture.
How do you change a tombstone on a light fixture?
0:252:36Replacing a Tombstone - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll push these tabs. In. And it will pop down see how it's hanging. Break the teeth out. And weMoreYou'll push these tabs. In. And it will pop down see how it's hanging. Break the teeth out. And we have a bad tombstone right here. You're going to fold wires. Out that tombstone right there.
How do you change a ballast without turning off power?
Remove the wire nut from one of the power wires and carefully strip about 1/2 inch of insulation from the end, making sure not to touch the end. Hold the ballast wire next to this wire with the stripped ends parallel but not touching. Quickly slip on the wire nut and screw onto the ends.
How do you release a wire from a push switch?
0:161:39How To Remove Wiring Pushed Into A Light Switch-DIY Electrical - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you're gonna simply press it into the slot. And press it down into the slot and as you areMoreAnd you're gonna simply press it into the slot. And press it down into the slot and as you are pressing it down into the slot you can simply pull the wiring out.
How do you release a push in wire outlet?
1:112:19How to Release Wires from a Push-In Connection on Electrical Wall OutletsYouTubeStart of suggested clipEnd of suggested clipOkay what we do is we take the small screwdriver and stick it into the rectangular slot that'sMoreOkay what we do is we take the small screwdriver and stick it into the rectangular slot that's directly under the wire. We push that in with our thumb. And pull the wire with the other hand.
How do you strip wires?
0:563:41How To Strip Wires Without Wire Strippers-Using Pliers InsteadYouTubeStart of suggested clipEnd of suggested clipBut squeeze them just a bit until you feel a little bit of pressure and rotate. The wire. SoMoreBut squeeze them just a bit until you feel a little bit of pressure and rotate. The wire. So continue rotating the wire. And use those blades to simply cut the skin or the outside portion.
How do you change an electrical ballast?
2:047:26How to Replace a Fluorescent Light Ballast - YouTubeYouTubeStart of suggested clipEnd of suggested clipPiece out in the middle. And there's just some little clamps here but we just have to squeeze. AndMorePiece out in the middle. And there's just some little clamps here but we just have to squeeze. And pull in a little bit. And now we have the ballast exposed. This is what we're gonna replace.
What happens if you wire a ballast wrong?
If a ballast fails, it can cause a short, burn out tubes or even cause a fire, so it must be replaced. Lights that don't turn on, fluorescent tubes blackened near their ends, and brown, burnt tube electrodes are all indicators that a ballast is bad.
How many wires does a ballast have?
The replacement ballast provides 5 wires: black, white, blue, blue (equivalent) and red. Incoming electrical power at the fixture connects to the line BLACK and WHITE wires shown on the diagram.
Is it hard to change a ballast?
You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
How to fix a tombstone with a wire?
Insert the paper clip into the damaged tombstone next to one of the two tombstone wires. The paper clip opens the tension spring connector inside the tombstone and allows you to pull out the wire. Repeat this for the remaining wire attached to the tombstone.
How to replace a tombstone with fluorescent wire?
Insert the paper clip into the wire hole on the replacement tombstone. Push the fluorescent fixture wire into the tombstone next to the paper clip. When you remove the paper clip, it allows the tension spring connector to clamp onto the fixture wire. Repeat this for the remaining fluorescent fixture wire.
What happens when a fluorescent fixture is damaged?
When a tombstone becomes damaged, it can no longer provide the proper electrical connection to light the tube. In some cases, one damaged tombstone could cause the entire fixture to fail. Replace the tombstone in ...
Can a tombstone cause a fluorescent light fixture to fail?
In some cases, one damaged tombstone could cause the entire fixture to fail. Replace the tombstone in the fluorescent light fixture so your fluorescent tubes glow once again.
How to get dirt off a gravestone?
Using a pump sprayer, which can be bought at garden centers and home improvement stores nationwide, eliminates the transfer of dirty water. Spray the gravestone with water, soaking it completely. Always use water first to try to remove as much of the dirt and grim that is on the headstone.
How to clean a gravestone without transferring water?
Using a pump sprayer allows you to rinse off the gravestone without transferring any dirty water to it. When you use a bucket to clean with, swish the scrub brush in the water when cleaning. This only transfers the dirty water back to the headstone. Using a pump sprayer, which can be bought at garden centers and home improvement stores nationwide, ...
How to clean a headstone with ammonia?
If the headstone you are cleaning is made from marble or limestone, add one tablespoon of ammonia to the non-ionic soap water mixture. Use only a soft bristled brush such as an automotive detailing brush or a soft toothbrush.
How often should you clean a tombstone?
Once you have scrubbed the headstone, rinse thoroughly. Avoid cleaning limestone, marble or sandstone more than once every 18 months.
How to clean moss off a headstone?
Removing the moss may cause more harm than good. Water and soap. When cleaning a headstone always use clean water . Rain water is less damaging then tap water, since it does not contain as many chemicals. If possible, collect rain water in a container weeks before cleaning the headstones.
Can you clean a headstone?
If the headstone is in disrepair, do not attempt to clean it. Cleaning a damaged headstone can make it worse. If the headstone is brittle or flaking, look into getting it repaired. If the headstone has moss or fungi growing on it do not attempt to remove it. Removing the moss may cause more harm than good.
