How to Replace a Dryer Belt
- Preparation. Unplug your dryer from the power. ...
- Remove the Old Belt. Once you’ve turned the power off and pulled your dryer out from the wall, the next step is to remove the top panel of the dryer.
- Install the New Belt. Now that you’ve removed the old belt, you can install the new one. ...
- Put the Dryer Back Together. ...
- Reconnect the Dryer. ...
Full Answer
How to replace a belt on an electric Hotpoint dryer?
How to Replace a Belt on an Electric Hotpoint Dryer
- Unplug the dryer and pull it out from the wall. Take out the upside-down screws in front that hold down the top.
- Take out the screws that hold the front of the dryer in place, which will be on the upper inside of the box, on either side, facing toward ...
- Slip the belt off the dryer drum from the front. ...
How to put a belt on a dryer drum?
Install the new belt by positioning it on the drum. Most dryers require the groove side of the belt to be facing inward. Loop the belt on the idler pulley and the drive pulley in a zigzag formation. You can rotate the drum to help align the belt. With the new belt in place, reassemble the dryer by aligning the drum on the front bulkhead, if ...
How do I change the belt on my Maytag dryer?
- Unplug the washing machine and turn off both the hot and cold water supply lines.
- Tilt the machine so it's lying on its front panel.
- Remove the shield from the bottom of the appliance.
- Remove the belt.
- Insert the new belt.
- Put the shield back into position.
- Lift the machine upright.
How to replace my Hotpoint dryer belt?
- Safety first! Unplug the machine from the wall-socket and make sure the machine is cool.
- Remove the top cover of the machine by undoing the 2 screws at the back of the top panel.
- You should now be able to see if the belt is broken or not.
Can I replace a dryer belt myself?
Replacing a dryer belt is an easy DIY task. It can be tricky to loop the belt around the pulley system when the drum is in, but practice makes this easier. Most people will already possess the tools required for the replacement. The whole job should only take 20-60 minutes.
How do you replace a dryer drive belt?
InstructionsShut off the power. Unplug the dryer. ... Raise the top panel. Pull the lint screen out of the housing in the top panel of the dryer. ... Remove the front panel. ... Remove the drive belt. ... Install the new drive belt. ... Reinstall the front panel. ... Reassemble the top panel. ... Restore power to the dryer.
How much does it cost to replace a drive belt on a dryer?
Cost to Replace a Dryer Belt Replacing a dryer belt ranges from $150 to $250. Dryer belts break under too much stress, so you should avoid overloading the dryer.
Where is the drive belt on a dryer?
How Does a Dryer Drum Belt Work? The dryer belt goes around the outside of the drum and is looped onto a drive pulley attached to the dryer motor shaft which drives the belt, and around an idler pulley which applies tension to the belt.
How do you know if a dryer belt is bad?
0:101:18Washer & Dryer Repair : How to Tell if a Dryer Is Broken - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst off if your drum doesn't turn. It's likely that your belt is either broken or off so you'reMoreFirst off if your drum doesn't turn. It's likely that your belt is either broken or off so you're gonna want to get into that and remove the drum.
How do I know if my dryer belt is slipping?
If you notice these 4 problems you're in luck because a dryer belt is an easy fix.Dryer Won't Start. Of course, there are many possible reasons your dryer might not respond when you push the start button. ... Dryer Stops Before Clothes Are Dry. ... Belt Noises. ... Drum Won't Turn.
Is it worth fixing a dryer belt?
Dryer runs and heats up but the drum doesn't turn If you're not mechanically inclined, it can be a clumsy repair. But like the heating element, belts can last 10-20 years, so it's worth doing even if you have to pay someone to do the repair.
Can I use a dryer with a broken belt?
A Bad Belt Has To Be Replaced The old belt is taken off, and a replacement belt is put back on. Changing a dryer belt is a common repair that doesn't cost too much since a belt is inexpensive. However, the belt is an essential part, and your dryer won't work without it.
How long should a dryer belt last?
Dryer belts usually last the dryer's lifetime. This is typically 8 to 14 years. Frequent use and heavy loads increase the rate of wear, reducing the dryer's lifespan. Sometimes, belts need replacement even if they aren't broken and are just loose.
What does it mean when your dryer doesn't spin anymore?
One of the most common reasons your dryer won't spin is because the drive belt is broken. To find out if this is the problem, open the dryer door, reach in, and attempt to turn the big circular tumbler—the drum—by hand. If it turns too easily, the belt has probably snapped and needs to be replaced.
What causes a dryer belt to break?
Dryer belts will break time after time if they are improperly installed, the wrong size for the dryer, or if the dryer is often overloaded. A broken pulley system, damaged drum felt seal, blocked blower wheel, or seized drum rollers would also cause the belt to keep breaking repeatedly.
Why did my dryer stop spinning?
A broken drive belt is the most common reason a dryer won't spin. To fix this issue, turn the drum by hand. A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken.
Are all dryer belts the same length?
Not all dryer belts are the same size. Dryer belts differ in diameter and length according to size, make, and model of the dryer in which they are installed.
Why is my dryer drum not spinning?
A broken drive belt is the most common reason a dryer won't spin. To fix this issue, turn the drum by hand. A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken.
Why is my dryer making a squeaking noise?
The dryer bearings and motor need to be replaced. A faulty motor is usually identified by squeaking or grinding sounds, not by a burning smell. If the squeaking sound is coming from the back of the dryer, a faulty motor or bad bearings may be the problem.
What causes squeaky dryer when running?
A screeching dryer can be caused by several things including a loose idler, a defective, old, or damaged dryer belt, an old motor, and worn or missing glide bearings.
How to reinstall drum belt?
Wrap the new belt around the drum when you are ready to reinstall it. Observe the drum, you should see a mark where the old belt fit the drum, and make sure the new belt is set at the same location. Slide the drum back into the machine, and support the front of the drum to hold it in position.
How to stop dryer from burning?
The easiest way to do this is to simply unplug it from the receptacle. This will prevent accidental electrical shocks and burns. Move your dryer to an area where it will be easy to access the rear of the machine if possible. This means disconnecting the vent duct and unplugging the electrical power if not already done.
Why is my dryer drum still in place?
If it is still in place on the drum, you may have a problem with the electric motor which turns the drum or the electrical switches that control the dryer's functions instead of a belt problem. Unplug the electrical wires at the front of the dryer that connect to the door safety switch.
Why does my dryer fail?
One of the most common causes for a clothes dryer to fail is a broken drive belt on the dryer drum. This is an easy do it yourself repair, which uses very few tools, and can save a lot of money. Here are the steps for accomplishing this task.
What size washer screws do dryers use?
Most dryers body screws are either 1⁄4 inch (0.6 cm) or 5⁄16 inch (0.8 cm) machine screws, so a nut driver of the right size will make this job easier, but even a pair of common pliers will do in a pinch. ...
Where to check for lint filter on dryer?
Check the outside of the machine near the top for any exposed fasteners. Most dryers built in the last 20 years have hinge-like clips on the rear, and snaplock fasteners under the top to make removing the top easier. Check at the lint filter access door for additional fasteners, usually counter-sunk phillips type machine screws.
How to secure drums?
Push the front completely in, lifting it over the latches and allowing it to drop onto them to secure the bottom in position. Push the top in, making sure the seals fit inside the drum snugly, without damaging them. These seals are usually felt, or some other soft material, and are held in place with an adhesive. ...
How to attach a belt to a motor?
To attach the new belt, begin by placing the belt, with the groove side down and lined up with the markings around the drum. Then loop the belt under the idler pulley (that has a moving wheel) and attach it back to the motor . The idler pulley should apply tension to the belt. You may need an extra hand for this step since ...
Where to put putty knife in dryer?
Next, take the putty knife and place it in the opening between the top of the dryer and the front of the dryer. Pop up the top of the dryer and repeat on the other side.
What should the idler pulley do?
The idler pulley should apply tension to the belt. You may need an extra hand for this step since the dryer drum can sag down and make it difficult to reach the motor. ...
How to disconnect lid switch wires?
You may need to disconnect the lid switch wires if they are not long enough to allow this. Release the belt from around the drum. To do this , the belt will be looped under the idler pulley and then attached to the motor. Reach under the drum and unhook the belt from around the motor.
How to pop felt out of drum?
Make sure the rear felt on the back end of the drum isn't folded under. If it has, use a screwdriver to pop the felt out while spinning the drum with your hand.
Where to put plastic guides on dryer drum?
Add the front plastic guides to the front of the dryer drum .
Can springs be removed from a door?
The springs can be removed from the door to allow the front to be moved completely away.
Where are the screws on a dryer?
Open the dryer door and find the two screws located just below the lint filter. You can then unthread the screws and remove them.
How to remove bulkhead from dryer?
Find the bulkhead (check your manual if necessary), and then unthread the screws that hold it in place. The bulkhead should then be able to be removed from the dryer unit.
How to reattach a support piece?
Reattach the support piece by aligning it into the right slots, and then rethread the screws back into place.
Why does my dryer not work anymore?
The drum belt in your dryer is the main component in your dryer that makes it turn around during a cycle. Sometimes it can break or become defective through normal wear and tear or if you overload your dryer too often. When this happens, it will need to be replaced, or your dryer won’t work anymore. These are general instructions and steps can vary by model and brand.
Can you unclip a top wire harness?
You can now unclip the top wire harness from the harness restraints and move it out of the way (you don’t have to fully remove it).
Can you plug a dryer back into the power?
Now that the dryer is back together, you can plug the dryer back into the power and put it back against the wall.
Step One: Disconnect the Dryer
The first step is to disconnect your dryer from the power source. You can then pull your dryer out from its cabinet (if applicable) so that you will be able to work on it.
Step Three: Install the New Belt
Now that you’ve removed the old belt, it is time to install the new belt. To do this:
Step Four: Put the Dryer Back Together
Once the new drum belt is attached correctly, you will need to put the dryer back together again so you can test it out. To put the dryer back together you need to:
Step Five: Reconnect the Dryer
The final step is to reconnect your dryer back up to its power source and test that the dryer is now working correctly. If your dryer passes the test, then it is fully fixed up and ready to go.
