How do you take apart a Kohler single handle faucet?
- Turn off the water to the faucet.
- Remove the plug button from the handle (Fig. …
- Loosen the screw underneath the plug button to remove the handle (Fig. …
- Unscrew the bonnet counterclockwise to expose the valve and the mounting nut; the bonnet should remove easily by hand (Fig.
Full Answer
How do you repair a Kohler faucet?
- Hold the handle with one hand. Using your other hand, turn the skirt, the decorative flared piece below the handle, counterclockwise.
- Remove any remaining components to expose the valve. Set all parts aside for re-use.
- The valve can now be replaced or other repairs made.
- Reassemble handle parts in reverse order.
How do you remove the cartridge from a Kohler faucet?
- TURN OFF WATER. Turning off the water at the shut off valves under the sink.
- PRY OFF HANDLE. Pry off the handle cap using a small flat screwdriver.
- REMOVE HANDLE FROM ASSEMBLY.
- REMOVE THE RETAINING NUT.
- REMOVE THE RETAINING CLIP.
- REMOVE THE O-RING.
- REPLACE THE CARTRIDGE.
- REINSTALL THE O-RING.
How to uninstall a kitchen faucet?
- 2 Turn Off the Water. Whether you’re updating or replacing a leaky faucet, always turn off the water first. ...
- 4 Remove Mounting Nuts Or Screws. After you’ve disconnected the water supply lines, it’s time to separate the faucet from the sink, countertop or wall.
- 5 Remove the Faucet. ...
- 6 More Tips on Removing a Kitchen Faucet. ...
How to change out kitchen faucet?
How to Replace a Kitchen Faucet
- Pick up key parts at the hardware store before you start. ...
- Gain access and remove the old faucet. ...
- Now install the new faucet. ...
- Required Tools for this how to replace a kitchen faucet Project. ...
- Required Materials for this how to replace a kitchen faucet Project. ...
How do you replace a Kohler bathroom faucet valve?
0:271:47Replace Two Handle Ultra Glide Valves - Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe valve body and untwist the handle. Once the valve body is out of the faucet remove the handleMoreThe valve body and untwist the handle. Once the valve body is out of the faucet remove the handle from the existing. Body attach the hardware to the valve body including the hose.
How do you remove a Kohler single handle bathroom faucet?
Single-Handle Bathroom Sink Faucets - Handle RemovalUsing a bladed screwdriver, gently pry off the plug button under the handle, taking care to protect all finished surfaces.Using a 1/8" hex wrench, loosen the setscrew securing the handle to the valve stem.Lift off the handle.Unthread the bonnet to expose the valve.
How do I know what model Kohler faucet I have?
The model number is printed on a tag that is attached to the cold water supply line of the faucet. The supply line is located below the sink, countertop, bath rim, or behind the bowl of a bidet. The model number, or part number, is typically preceded by "P/N."
How do you remove an old Kohler faucet?
How To Remove Kohler Kitchen Faucet?Turn off the water valve for the cold and hot water.Disconnect the water lines from the cold and hot water valves.Loosen the mounting screws.Unscrew the mounting nuts under the sink.Pull out the faucet from the sink. Apply a slight pressure if the faucet is sealed by caulk.
How do you replace a single handle bathroom faucet?
1:404:03Bathroom Faucet Installation (1 Handle 1 Hole | Pop-Up ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf necessary unscrew the lines from the bottom of the faucet. Next unscrew the mounting nuts. ThenMoreIf necessary unscrew the lines from the bottom of the faucet. Next unscrew the mounting nuts. Then unclip the lift rod from the mechanical pop up and unscrew the extension rod.
How do you remove a Kohler faucet handle?
Once the water is off, drain excess water from the supply lines by turning on the faucet. Then, to remove the handle, simply twist the decorative skirt around the base of the handle counterclockwise using your hand. Hold the handle itself firmly in your other hand while you rotate the skirt.
Do KOHLER bathroom faucets have a lifetime warranty?
Kohler faucets, both kitchen and bathroom fixtures, come with a limited lifetime warranty that protects their components. The company ensures that all faucets manufactured after January 1, 1997, will be leak and drip-free during everyday residential use.
Does KOHLER replace parts for free?
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from date of installation. Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co.
Where is KOHLER model number?
The model number is located inside the tank, either molded into the china or stamped with blue or black ink. The model number consists of four or five digits and may include a K prefix. In some cases, the model number is preceded by 97 or F.
How do I remove the cartridge from my Kohler bathroom faucet?
1:384:19Kohler Bathroom Faucet Cartridge Replacement _Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff the water turned off and the socket wrench in place then you want to loosen up the cartridge byMoreOff the water turned off and the socket wrench in place then you want to loosen up the cartridge by turning counter clockwise. If you meet resistance.
How do you tighten a loose Kohler bathroom faucet?
1:213:46SBW#8 - A Loose Bathroom Faucet Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you need to this will turn free still and then set it back back down exactly the way youMoreAnd then you need to this will turn free still and then set it back back down exactly the way you want it once the on to the the Grimm's hand on groom wheel. And then once it's down.
How do I stop my faucet from dripping?
0:072:54How To Fix A Dripping or Leaky Double Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe aerator if it won't unscrew soak a towel and white vinegar and wrap it around the aerator toMoreThe aerator if it won't unscrew soak a towel and white vinegar and wrap it around the aerator to help loosen mineral deposits. After an hour gently twist off the aerator.
How do you remove a Kohler faucet handle without screws?
You can use an allen wrench (also called an allen key) to remove it. Once you've done that, you can typically just lift the faucet handle off. However, if it has a cartridge inside, you may need to unscrew a top piece as well to be able to remove the cartridge.
How do I remove a single handle faucet?
0:302:45How to remove & replace single-handle pullout kitchen faucetYouTubeStart of suggested clipEnd of suggested clipNew. Hoses. Next loosen the faucet retaining nut. It's this nut right here i just couldn't recordMoreNew. Hoses. Next loosen the faucet retaining nut. It's this nut right here i just couldn't record and loosen it at the same. Time. After that you will be able to remove the bracket.
How do you take apart a single handle faucet?
0:182:44Repairing a Leaky Single Handle Ball-Type Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis may require using an Allen wrench to loosen the handle. There may be a button that covers theMoreThis may require using an Allen wrench to loosen the handle. There may be a button that covers the screw that needs to be removed first and then you can loosen the screw and remove the lever handle.
How do you remove a Kohler Forte handle?
0:292:07KOHLER Forte Pull-Out Kitchen Sink Faucet O-Ring and ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a hex wrench loosen. But do not remove the set screw holding the handle in place lift theMoreUsing a hex wrench loosen. But do not remove the set screw holding the handle in place lift the handle off the faucet. Body turn the bonnet counterclockwise to remove it from the faucet.
How to find Kohler model number?from elookahead.com
First, find the model number (P/N number) of your fixture, which is located on a tag attached to the faucet’s cold water supply line. Because Kohler parts have a lifetime warranty, they will be replaced for free by contacting Kohler’s Customer Care Center at 1-800-456-4537 or by visiting this Internet address. You should receive the parts by mail within a week to ten days. Here’s a list of parts you’ll need:
Where is the plug button on a faucet?from elookahead.com
The plug button is a small oval button in the back of the faucet handle. With the handle in the up position, pull the button out. If it isn’t easily removed, place the tip of a small screwdriver underneath the faucet handle skirt, which is directly behind the plug button, and push out. Remove the button with a thin prying device (or your fingernail).
How to remove control valve cartridge?from elookahead.com
To get to the control valve cartridge, use the 1 1/16” open end wrench (or crescent wrench) to remove the large hex nut cover at the top of the faucet body. Hold the faucet body with your hand to keep it from turning while “wrenching off” the top cover. If the faucet body slips in your hand, place a washcloth around the body and use a channel lock to keep it from spinning as you remove the top cover.
How to repair a broken door?from elookahead.com
Collect the tools and supplies you’ll need before beginning your repair project. This will make the process much easier, less frustrating, and you’ll complete the repair a lot faster. Here’s what you’ll need: 1 1/8″ Allen Wrench 2 3/8″ Box or Open End Wrench 3 1 1/16″ Open Wrench (or adjustable wrench that will open to this size 4 Channel Lock 5 Hammer 6 Wide Blade Screw Driver (non-metallic if you have one) 7 Small Screw Driver (or knife-edged device) 8 Needle-Nose Pliers 9 Paper Towels 10 Old Wash Cloth or other heavy cloth 11 Mild Cleaning Product 12 Something to Cover Sink Drain (s) 13 Portable Light
Why is my sink sprayer leaking?from elookahead.com
If there are still leaks under your sink when you turn on the faucet, the end of the plastic connector (see below photo) may have deteriorated, causing the spray handle/hose assembly to develop a leak . A simple test to confirm that this is the problem, is to pull out the sprayer, turn on the faucet, and watch for leaks around the base of the sprayer. If there are leaks, then you will need to repair the sprayer/hose assembly, as shown below.
Where is the diverter on a faucet?from elookahead.com
The Diverter is a small circular assembly located in the back of the faucet. If you are unable to pull it out with your fingers, remove it with needle-nose pliers. Push the new Diverter, fins pointing out, into place with your fingers.
Can you use a faucet while a replacement part is in transit?from elookahead.com
So that you can continue to use your faucet while the replacement part is in transit, pull out the sprayer and leave it in the sink. By doing this, any leaks from the sprayer will go down the drain instead of leaking onto the floor under your sink.
How to find Kohler model number?from elookahead.com
First, find the model number (P/N number) of your fixture, which is located on a tag attached to the faucet’s cold water supply line. Because Kohler parts have a lifetime warranty, they will be replaced for free by contacting Kohler’s Customer Care Center at 1-800-456-4537 or by visiting this Internet address. You should receive the parts by mail within a week to ten days. Here’s a list of parts you’ll need:
Where is the plug button on a faucet?from elookahead.com
The plug button is a small oval button in the back of the faucet handle. With the handle in the up position, pull the button out. If it isn’t easily removed, place the tip of a small screwdriver underneath the faucet handle skirt, which is directly behind the plug button, and push out. Remove the button with a thin prying device (or your fingernail).
How to remove control valve cartridge?from elookahead.com
To get to the control valve cartridge, use the 1 1/16” open end wrench (or crescent wrench) to remove the large hex nut cover at the top of the faucet body. Hold the faucet body with your hand to keep it from turning while “wrenching off” the top cover. If the faucet body slips in your hand, place a washcloth around the body and use a channel lock to keep it from spinning as you remove the top cover.
How to repair a broken door?from elookahead.com
Collect the tools and supplies you’ll need before beginning your repair project. This will make the process much easier, less frustrating, and you’ll complete the repair a lot faster. Here’s what you’ll need: 1 1/8″ Allen Wrench 2 3/8″ Box or Open End Wrench 3 1 1/16″ Open Wrench (or adjustable wrench that will open to this size 4 Channel Lock 5 Hammer 6 Wide Blade Screw Driver (non-metallic if you have one) 7 Small Screw Driver (or knife-edged device) 8 Needle-Nose Pliers 9 Paper Towels 10 Old Wash Cloth or other heavy cloth 11 Mild Cleaning Product 12 Something to Cover Sink Drain (s) 13 Portable Light
Why is my sink sprayer leaking?from elookahead.com
If there are still leaks under your sink when you turn on the faucet, the end of the plastic connector (see below photo) may have deteriorated, causing the spray handle/hose assembly to develop a leak . A simple test to confirm that this is the problem, is to pull out the sprayer, turn on the faucet, and watch for leaks around the base of the sprayer. If there are leaks, then you will need to repair the sprayer/hose assembly, as shown below.
Where is the diverter on a faucet?from elookahead.com
The Diverter is a small circular assembly located in the back of the faucet. If you are unable to pull it out with your fingers, remove it with needle-nose pliers. Push the new Diverter, fins pointing out, into place with your fingers.
Can you use a faucet while a replacement part is in transit?from elookahead.com
So that you can continue to use your faucet while the replacement part is in transit, pull out the sprayer and leave it in the sink. By doing this, any leaks from the sprayer will go down the drain instead of leaking onto the floor under your sink.
How to disconnect hot water line from faucet?
Turn the hot water supply line connected to the underside of the faucet counterclockwise with an adjustable wrench to remove it. Repeat to disconnect the cold supply line. Clean up any water with a towel.
Can you remove a Kohler faucet?
Kohler Faucet Removal. If you need to replace a broken faucet or wish to install a more modern faucet, you must first remove your old one. The procedure for removing a Kohler faucet is the same as any other brand of faucet, and only a few tools are required.
