How To Replace an Actuator Valve
- First make sure there is no power going to the control box.
- The actuator is held in place by four screws and one plastic screw on the top of the handle. ...
- Remove the top plastic screw. The plastic handle it was over can now be pulled straight up and off.
- Next you want to remove the 4 visible screws that hold the actuator in place. The actuator can now be pulled straight up and off.
- If this actuator is connected to an automated control system, it will be connected to the circuit board.
- Remove the 4 visible screws and remove the panel cover (s).
- A majority of systems will have the connection line marked on the board “Actuator.”
- Remove the old connection and place the old actuator and wires to the side.
- Next, Using the old connection line, install the new actuator connection to the control board.
- Before you place the new actuator onto the valve, you need to confirm that both the valves are faced in the same position.
- Next place the plastic handle onto the old valve fitting. ...
- Now remove the plastic handle and install the new actuator onto the valve.
- Next install the 4 screws on the top of the actuator to secure it in place.
- Place the handle onto the new actuator and screw the plastic screw into place.
- If you need to manually shut off an actuator, set this toggle switch to the middle position. ...
What is a pool actuator and how does it work?
Pool valve actuators provide an automated command by push-button that goes to one of the diverter valves or more in the pool’s water flow system. You will find it on your pool’s diverter valve and it will be wired in the pool’s control box. How Does a Pool Actuator Work? Diverter valves can be installed for a manual operation or automated one.
How much does it cost to fix a Pentair pool actuator?
Fix your Pentair Pool Valve Actuator for under $1. (Compool CVA-24 bad limit switch). - YouTube Fix your Pentair Pool Valve Actuator for under $1. (Compool CVA-24 bad limit switch). If playback doesn't begin shortly, try restarting your device.
How do you sync pool Valve actuators?
To sync the pool valve actuator, the automated actuators on pool valves one and two must rotate in the same direction when changing from pool to spa mode. If one turns in the opposite direction from the other one, the actuators need to be adjusted to sync them.
How do I install the actuator on the valve?
1 Ensure the actuator and valve are positioned the same. 2 Install the mounting hardware on the valve but leave the bolts loose for now. Mount the actuator to the valve and... More ...
How do you install a valve actuator?
INSTALLATIONManually open valve.Remove valve mechanical stops. ... Check again that the valve and actuator are in the same position.Install mounting hardware on valve, do not tighten bolts securely at this time, mount actuator to valve, and once actuator screws have been started securely tighten all nuts and bolts.More items...•
How do you remove valve actuator?
0:576:17Remove and Reinstall a Valtek VL Actuator on a MK1 Control ValveYouTubeStart of suggested clipEnd of suggested clipLoosen the stem clamp bolt. The stem clamp bolt and nut do not need to be removed only loosenedMoreLoosen the stem clamp bolt. The stem clamp bolt and nut do not need to be removed only loosened remove the packing bolting. Note during this staff the actuator yoke will move away from the bonnet.
What is a pool valve actuator?
Valve actuators are motorized/mechanical devices used to open and close pool pump valves. Valve actuators are available for 2-way and 3-way diverter valves to easily and automatically control poo/spa combinations and water features.
Are pool Valve Actuators universal?
There are different versions of actuators from all of the major swimming pool parts manufactures including Jandy, Pentair, Hayward, and Intermatic and all of these are universally compatible with each other.
How do you change a Pentair valve actuator?
0:093:42How To Replace A Valve Actuator - Chlorine King Pool Service - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is the one we're gonna replace it the first thing I'll do is remove the handle. Here. KeepMoreThis is the one we're gonna replace it the first thing I'll do is remove the handle. Here. Keep track of the orientation. So off is facing towards me right now towards the spa returns.
How do you dismantle an actuator?
2:394:25Air Operated Valve Disassemble - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can remove the actuator stem through the bottom of the yoke.MoreYou can remove the actuator stem through the bottom of the yoke.
How long do pool Valve Actuators last?
Pool Automation is technology-based, and even though it should last you 10 years or more, you need to weigh the advantages of new simpler and more advanced automation products against the repair costs of your old automation.
How do you control a pool actuator?
1:202:53Pool Valve Actuator Manual Mode & Manual Override part 1 of 2YouTubeStart of suggested clipEnd of suggested clipIf your jandi actuator valve fails you can do is connection loosen the nut a little bit and pressMoreIf your jandi actuator valve fails you can do is connection loosen the nut a little bit and press down really hard. And then he activates the motor you can actually turn the handle.
What does a Hayward valve actuator do?
Hayward valve actuator rotates 2-port or 3-port valves automatically. It can be used with the Aqua Logic system to automate pool/spa operations, cleaner operations, water features, or a variety of other uses. The unique cam setting feature ensures a quick and easy installation with the precise control of water flow.
How do I change my Jandy actuator?
0:3910:08How To Replace A Jandy Automatic Actuator Valve Properly! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis there's four main screws to remove it from the housing valve you need this one here this oneMoreThis there's four main screws to remove it from the housing valve you need this one here this one here this one here and this one here go to release those four screws.
How does a valve actuator work?
Torque is the rotational force an actuator generates to close a rotational valve. Electric actuators can generate this force by transmitting it to the output shaft and then the valve stem. When pressure is applied to the valve stem, the valve's orifice opens or closes.
What does a Jandy actuator do?
Jandy Valve Actuators are designed to meet the needs of today's more advanced, automatic pool equipment. These fully adjustable actuators offer versatile pool/spa automation with easy setups. All actuators work with the Jandy AquaLink® RS Control Systems and are available in 24 volt units.
How do you remove a central heating actuator?
1:1811:04How to replace a central heating 3 port divertor valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the button and then you just pull it and it just comes off okay you can see the button thereMorePress the button and then you just pull it and it just comes off okay you can see the button there just be she moves that plastic clip.
How do you remove a pneumatic valve?
7:509:17Air Operated Valve Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipClick on the yoke lock nut to unscrew and remove. Now that everything is loose firmly lift the yokeMoreClick on the yoke lock nut to unscrew and remove. Now that everything is loose firmly lift the yoke assembly straight up and then away from the valve stem.
How do I remove Belimo actuator from valve?
0:506:22How to Remove the Actuator from the Belimo ZoneTight Zone ValveYouTubeStart of suggested clipEnd of suggested clipAnother one I pull straight up and away. If this is already installed in a piping system it's muchMoreAnother one I pull straight up and away. If this is already installed in a piping system it's much easier in this example here I'm just holding it out in the open I'm. Gonna put it back together.
How do you change the Siemens actuator?
2:004:43Siemens Actuator Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext insert the anti-rotation bracket into the slot at the bottom of the actuator. This bracket canMoreNext insert the anti-rotation bracket into the slot at the bottom of the actuator. This bracket can be oriented at different angles or bent to stand off in an application.
What is a goldline valve actuator?
The Goldline valve actuator is simple to operate by design. This actuator is engineered to support both two and three-way valves that are installed easily using just a screwdriver. Extremely adjustable cams act to give this actuator flexibility that many others do not possess on the market.
What is Intermatic 24V valve actuator?
Quality is foremost in the Intermatic’s 24-volt valve actuators. These actuators provide quality control of 2 and 3-way diverter valves for any pool/spa combinator or water feature. Adjust the water flow for a particular application with the adjustable cam that rotates the diverter valves to multiple degrees.
How to sync pool valve actuator?
To sync the pool valve actuator, the automated actuators on pool valves one and two must rotate in the same direction when changing from pool to spa mode. If one turns in the opposite direction from the other one, the actuators need to be adjusted to sync them.
What type of actuator is used to operate valves?
These actuators are one of the most reliable and common kinds of valve actuators. Electric actuators can operate some of the largest valves and are powered by a three-phase electric motor that uses a mixture of gears and level spurs.
What is the difference between hydraulic and pneumatic actuators?
With hydraulic actuators the actuators move the cylinder by pressurized air while hydraulic actuators use pressurized air. A pneumatic actuator isn’t a practical choice for large equipment that needs substantial bore cylinders due to compressed air intake.
Why are manual actuators different from automatic actuators?
The manual actuators vary from automatic actuators because of the external power provided for the automatic valve movement. Manually operating a valve is not an option for many actuators due to the force required to turn the valve or because the application has valves in more remote pipelines.
What is a quarter turn actuator?
Quarter-turn pneumatic and hydraulic actuators are versatile and can be used, even when electricity is not available or when reliability and simplicity are prioritized. These actuators have a vast array of capabilities, including the small actuators that deliver a small number of inch-pounds of torque up to the biggest actuators that are capable of delivering more than a million inch-pounds of torque.
What is an actuator in a pool?
A swimming pool actuator is an automated valve that is either connected to a swimming pool automation system or a solar heater system. These occasionally stop working and need to be replaced. There are different versions of actuators from all of the major swimming pool parts manufactures including Jandy, Pentair, Hayward, and Intermatic and all of these are universally compatible with each other.
What happens if an actuator is connected to a control system?
If this actuator is connected to an automated control system, it will be connected to the circuit board. This will require you to remove the cover panel (s) of the control unit.
What are the different types of pool valves?
The four big ones to be aware of are: Multiport Valves. Diverter Valves.
How many outlets does a 3 way diverter valve have?
The 3-way diverter valve can be open and closed stop water completely, allow water through 1 of the 2 outlets, or allow water through both outlets.
Why are butterfly valves called butterfly valves?
The technical term for these are Butterfly valves because they can flap open and closed. No, there’s not a lepidopterarium (it’s a real word) or butterfly sanctuary, in the valve. Think of it as a big flap. When it’s closed, the flap completely blocks the pipe and stops all the water flow.
What is flocculant used for?
When using a flocculant, of course. Flocculants are used to clear cloudy pool water and need to be moved around your pool without being filtered out. If all of those functions weren’t enough, multiport valves actually have a winter setting too!
Why do you need a check valve in a pool?
Check valves, also known as non-return or one-way valves are installed in plumbing to prevent the backflow of water, usually due to gravity. Also, if the pump is turned off, there’s nothing to keep the water from flowing the wrong way. This could lead to some nasty situations ending up in your pool.
How does a solar pool heater work?
Solar pool heaters work by warming the pool water in the toasty rays of the sun, usually positioned on your roof for optimum coverage. When your pump is turned off, though, all of that water is just going to go splashing back down thanks to the laws of physics.
What is automatic chlorine?
These devices chlorinate your pool as the last stop the water makes as it moves through your filtration and circulation system, pumping super-concentrated chlorine into the water at the last second to sanitize your pool.
What is a spider gasket?
The spider gasket is the main diverter seal within your multiport valve. Spider gaskets divert water and keep it moving in the correct direction. It also keeps the flow moving on time as well.
Why does water come out of the waste port?
Another reason water might come through the waste port is a faulty valve spring. Occasionally, the valve spring may break or weaken. When this happens, the spider gasket won’t sit or seal properly and cause leaking out of the wrong port.
What does it mean when a multiport valve leaks?
However, if water rises from within the valve and overflows to the lid, you have a common multiport leak. Under the handle, on the stem of the diverter are gaskets. These gaskets prevent water from flowing through. A multiport valve that leaks around the handle means your gaskets are deteriorating or they are out of alignment.
How to keep pool clean?
A sure way to help keep your swimming pool clean is to actively maintain and repair your multiport valve before it gets to the point of no return. The multiport valve on your pool filter is essential. In fact, it acts sort of like the steering wheel on your car. The multiport valve controls the direction you want the pool water to flow in.
Why does my pool heater leak water?
One cause is when the pool heater shoots hot water back to the valve. The heat shrinks the PVC connector. As a result, water seeps through the gaps. However, over tightening the adaptor on the valve is probably the most common reason why leaks spring up near the pipes.
Can a multiport valve leak water?
Multiport Valve Leaks Out of the Waste Port. For the record, water is not supposed to come out of the waste port. So, if you’re not backwashing your filter and you see water leaking out of this line, it’s definitely not a good sign.
Where is the cover o-ring on a valve?
If everything pans out, your best bet is the cover o-ring. You can find the cover o-ring in the seam between the valve cover and main housing. To access this gasket, remove the 6 to 8 screws on the valve cover.
