Replacing it usually involves the following procedures:
- Removing the screws that hold the sheet metal access panel in place.
- Removing the access panel.
- Locating the tailgate handle holding screws..
- Backing the screws out of the cavity.
- Removing the tailgate latch rod clips on each tailgate handle’s side.
- Releasing the tailgate handle assembly from the tailgate.
- Putting the new handle into the access hole found on the tailgate’s backside.
Full Answer
How to fix a broken truck tailgate handle?
How to Replace a Tailgate Handle on a 1998-2011 Ford Ranger Pickup Truck
- Remove Tailgate Liner and Access Panel Covering the Handle. Remove eight T27 Torx bolts from the inside of the tailgate to remove the liner. ...
- Remove the Two 10mm Nuts Holding the Tailgate Handle in Place and Then Pull Handle Out. ...
- Before Installing New Handle, Spray Penetrating Oil Onto the Mechanism and Latches on Either Side and Apply White Grease. ...
How do you replace tailgate lift rods?
You will need to remove the latch with the gate open and pull the rod out with the latch, then you can change the rod and insert the rod as you install the latch. Customer: This is a pickup truck. The rod is located inside the tailgate.
How to align tailgate?
- Open and close the tailgate to check for flushness (b).
- Open the tailgate and loosen both strikers about 1/3 to 1/2 of a turn, enough for striker movement without losing the nut.
- Close the tailgate. ...
How do I remove the tailgate?
- Open the tailgate to the angle where you can release the brackets on the support cables from the lugs on both sides.
- To release the support cable bracket simply lift it up and slide it off.
- Tilt the tailgate to a thirty degree (30°) angle and pull up on the right side to unhook the right side.
How to remove a tailgate handle?
How to remove a T27 Torx?
About this website
How do you open a tailgate with a broken handle?
0:441:25How to open a broken tailgate - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then yeah the next step is get a screwdriver. And all you have to do is push down on this rightMoreAnd then yeah the next step is get a screwdriver. And all you have to do is push down on this right here. And there you go you can drop the tailgate lift the tailgate and load your dogs.
How do you remove a Ford tailgate handle?
2:086:25Ford F 150 Tailgate Handle Removal 2015-2017 - How to - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then pull out on the bottom and actually pull up it's going to release it from there and thenMoreAnd then pull out on the bottom and actually pull up it's going to release it from there and then you're going to have one. And two electrical harnesses to remove.
How much does it cost to fix a tailgate latch?
The average cost for tailgate lock cylinder replacement is between $99 and $110. Labor costs are estimated between $40 and $50 while parts are priced at $59. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
How do you remove the tailgate handle on a 2005 Chevy Silverado?
0:092:42How to Replace Tailgate Handle 1999-2006 Chevy Silverado - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have the top broken free just go ahead and lift this straight up and draw it away go aheadMoreOnce you have the top broken free just go ahead and lift this straight up and draw it away go ahead and come in between here with a nice flathead screwdriver. Pull that clip down grab.
What are the parts of a tailgate?
Tailgate PartsLiftgate/Tailgate Lock.Lift Support.Tailgate.Tailgate Cable.Tailgate Handle.Tailgate Hinge Kit.Tailgate Latch.Tailgate Lift Support.
How do you take off a tailgate?
0:001:57Easy Trick To Removing a Tailgate - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm going to come over and remove. The two cables one on each side now i have a little bumper. OnMoreI'm going to come over and remove. The two cables one on each side now i have a little bumper. On here because i have a tailgate assist. So you may or may not have that i put that on after.
How do you change a tailgate handle on a 2004 Chevy Silverado?
How to Replace Tailgate Handle and Bezel 2000-06 Chevy SilveradoInsert a small screwdriver into the handle bezel.Pry the bezel out and remove it.Push the lock rod tabs out.Lower the tail gate.Remove the Phillips head screws from the tailgate bezel.Remove the 13mm bolts from the tailgate handle.Remove the tailgate trim.More items...•
How do you change a tailgate handle on a Toyota Tundra?
No parts specified.Step 1 Tailgate Handle. ... Pull off the panel and then pull cables inward, causing tailgate to release and go down. ... Remove rubber pieces from cable and pull cable from insert. ... Use your 5/16th-in. ... Push in black clip to let handle fall out. ... Put new tailgate handle back in.More items...•
How long does it take to install a tailgate?
One (1) helper to assist with the installation. 4 or 5 chains at least 10 ft long (10 to 20 ft preferred)...Approximate Installation Time:Articulated Tailgate:35 - 50 man hours +/-Outriggerless Tailgate:45 - 60 man hours +/-Ultra-High Tailgate:45 - 60 man hours +/-2 more rows
How do you change a tailgate latch on a 2006 Chevy Silverado?
1:085:13How to Replace Tailgate Latch 1999-2006 Chevy SilveradoYouTubeStart of suggested clipEnd of suggested clipSomething that's gonna take a little bit of the slack off of this. Now I'm gonna grab on to this.MoreSomething that's gonna take a little bit of the slack off of this. Now I'm gonna grab on to this. Pull. It away lift. Up leave this hanging. Now we're going to remove our mounting bolts for the latch.
How do you fix a tailgate that won't close?
How to Fix a Tailgate That Won't LatchTest the Latches. Press the latch with a Phillips screwdriver and see if it latches. ... Test the Handle. Remove the outer trim piece from the tailgate handle with a trim tool. ... Test the Latch Pin. See if the striker pin or latch pin needs to be adjusted.
How do you unjam a tailgate on a truck?
2:194:01How To Open A Stuck Tailgate - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i'm just going to bang it toward hammering towards the left side of the truck toward the middleMoreAnd i'm just going to bang it toward hammering towards the left side of the truck toward the middle and that will pull it open pull the pull rod which will release the latch. On.
How do you open a Ford tailgate?
0:170:37Open your tailgate from inside your 2022 Ford F150 - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo across the steering wheel over to the left hand side. And you'll see this button right here withMoreGo across the steering wheel over to the left hand side. And you'll see this button right here with the same two times one two and the tailgate drops down.
How do you adjust a Ford tailgate?
0:010:23How to adjust the tailgate height on any Lincoln or Ford - YouTubeYouTubeStart of suggested clipEnd of suggested clipSet it to your desired height. And then all you do is hold this button. In it takes about three orMoreSet it to your desired height. And then all you do is hold this button. In it takes about three or four seconds. You're gonna hear an audible chime inside the cabin.
How to Replace Tailgate Handle 98-11 Ford Ranger - YouTube
Buy Now!New Tailgate Handle from 1AAuto.com http://1aau.to/ib/1ABTH000421A Auto shows you how to repair, install, fix, change or replace a broken or snapped ...
DIY How to Replace a Broken Tailgate Handle on a Ford Ranger Pickup ...
Ford Ranger Replacement Tailgate Handle on Amazon - https://amzn.to/2J3MCrYFind a replacement tailgate handle for your truck on Amazon - http://amzn.to/2snX...
SOLVED: How to open tailgate on ford ranger if the handle - Fixya
Look under the handle inside of the tailgate and you should find two metal rods that go out to each latch. Squeeze them both towards the center ... you should see an access panel that can be removed so you can undo the broken handle and replace it. Hope this helps, let me know Read full answer. Dec 09, 2009 • 1996 Ford F150 ...
Ford ranger: I can't get my ford ranger tailgate to open. - JustAnswer
The tailgate won't latch in place. 1998 Ranger, One of the rods had popped out of the little clamp near the middle, I got all of that put back in and the handle move those now, but now it won't latch …
SOLVED: I have a 1997 Ford Ranger. I can not lower the Ta - Fixya
How to replace Tailgate handle on 2006 Ford ranger? 1997 Jeep Grand Cherokee; Open Questions: 0 answers. how do I change a wheel baring in a ranger 4 wheel drive 1997 how do I change a wheel baring on a 1997 ranger front. Read full answer. Be the first to answer Sep 10, 2014 • 1997 Ford Ranger SuperCab.
How to remove a tailgate handle?
With a socket and ratchet remove the two 10mm nuts from the tailgate handle. Pull the handle down and out of the vehicle . This is how you remove the tailgate handle. These handles often break because the inside mechanism gets stuck or frozen.
How to remove a T27 Torx?
Step 1: Remove Tailgate Liner and Access Panel Covering the Handle. Remove eight T27 Torx bolts from the inside of the tailgate to remove the liner. Take the liner up and off of the tailgate. Remove the access panel covering the handle mechanism. The panel should come right off because the bolts were also holding it on.
How to fix a broken tailgate handle?
The actual broken tailgate handle repair is easy, just three bolts and a couple of plastic clips that hold the rods that operate the latches hold the handle in place. We unbolted the handle and popped the clips off. This allows us to replace the handle, but what about the latches? If you don’t take care of the latches now, the new handle will just break again down the road.
How many bolts are there in a tailgate latch?
There are two bolts holding the latches in place on each side. Only remove one at a time, as the tailgate cable has to be removed as well.
What oil to use to lubricate a latch?
With the latch out, we used some Slip Plate Black Ice graphite penetrating oil to lubricate the latch. The penetrating oil helps pull the graphite into the inner workings of the latch so that when the oil eventually dries up, the latch will have a protective coating of graphite for smooth operation.
When reinstalling latches, do you have to make sure the rod goes above the recess?
When the latches are reinstalled, you have to make sure the rod goes above the recess for the handle, otherwise you will have to pull it out and reinstall it.
Can a truck's tailgate handle break?
This can happen on any truck, but it doesn’t have to. The tailgate handles is not the issue here, it is actually the latches themselves. There are two latches, one on either side of the tailgate. Over time, these latches get coated with dirt and rust. When the lubrication is gone and the latch sticks, the increased effort required to open the tail gate stresses the cast iron arms on the handle. Put too much stress on these arms, and they break, leaving you with a busted tailgate.
How to remove a tailgate handle?
With a socket and ratchet remove the two 10mm nuts from the tailgate handle. Pull the handle down and out of the vehicle . This is how you remove the tailgate handle. These handles often break because the inside mechanism gets stuck or frozen.
How to remove a T27 Torx?
Step 1: Remove Tailgate Liner and Access Panel Covering the Handle. Remove eight T27 Torx bolts from the inside of the tailgate to remove the liner. Take the liner up and off of the tailgate. Remove the access panel covering the handle mechanism. The panel should come right off because the bolts were also holding it on.
