How do you replace a towel rack?
- Remove the old or broken towel bar from your wall.
- Use a cordless drill and make the existing holes in the wall larger so you can put in toggle bolts.
- Put the toggle bolts on the towel bar mounting hardware by sliding the screw into the mounting hole and threading the spring loaded piece onto the other side.
How to fix a broken towel rack?
How do you replace a towel rack? Remove the old or broken towel bar from your wall. Use a cordless drill and make the existing holes in the wall larger so you can put in toggle bolts. Put the toggle bolts on the towel bar mounting hardware by …
How to make a towel rack out of PVC pipe?
Dec 02, 2012 · Subscribe and visit our weekly podcast for more tips https://itunes.apple.com/us/podcast/fix-it-home-improvement/id880903087?mt=2I share some tips on towel b...
How to reattach a broken ceramic towel rack?
Nov 12, 2014 · Remove the Old Towel Bar Now that you’ve got your supplies, it’s time to go to work by removing the old towel bar. I easily pulled my bar out on its own since it was too short to begin with but if yours isn’t, you can remove it by sawing through the middle of it. 3. Cut Your New Replacement Bar to Size
How to take a towel rack off the wall?
Nov 20, 2013 · This is how to remove a towel rack from drywall. This same procedure should work for similar items that are mounted to drywall. It's important to sand and ...
1. Measure For & Buy Your Replacement Supplies
Figuring out the supplies that I needed was the hardest part – once I had them, this was a 10 minute fix. You’ll need two things – a replacement bar and spring-loaded end caps. For the replacement bar, measure to see whether you need a 3/4″ or 5/8″ bar and also measure the length that you’ll need and buy a replacement bar that is as long or longer.
2. Remove the Old Towel Bar
Now that you’ve got your supplies, it’s time to go to work by removing the old towel bar. I easily pulled my bar out on its own since it was too short to begin with but if yours isn’t, you can remove it by sawing through the middle of it.
3. Cut Your New Replacement Bar to Size
When cutting your replacement towel bar to size, it’s important that you not cut it either too long or too short. Here’s what I did – I put a spring-loaded end cap into one end of my chrome bar and then put that end into one of the fixed wall brackets.
4. Put the Spring-Loaded End Caps on the Bar Ends & Install It!
After cutting my replacement bar to the correct size, I put the spring-loaded end caps onto both ends of the bar and installed it between the two fixed brackets.
How to smooth out a caulk joint?
Let the caulk stiffen for an hour or so and then add caulk around the perimeter. Use a wet finger or rag to smooth the caulk joint. Let it sit overnight before you pull the tape, then caulk any edges hidden by the tape. Remember to put the rod in before setting the second fixture.
How to protect a tile fixture from scratches?
If the putty knife doesn’t hit anything hard, move on to the next step. Tape off the tile around the fixture to protect it from scratches. Then fit your oscillating tool with a flexible scraper blade and slide it under the fixture as shown.
Can you use old bar as template?
Note: Don’t use the old bar as a template (it didn’t have spring tensioners). Next, cut the bar to length ( photo 1 ): Mark the cut length on the new bar; cut the bar by hand with a hacksaw to prevent chipping; clean up the inside and outside edges with a utility knife before inserting the spring tensioners.
What is the standard size of towel bar?
Most towel bars come in three lengths – 18″, 24″, and 30″. An 18″ towel bar is great for small spaces and fits a single standard bath towel folded in half while a 24″ towel bar fits a single oversized bath towel folded in half. One may also ask, what is the standard size of a towel bar?
How high should a towel bar be above the floor?
Consequently, where should a towel bar be placed? Standard towel bars should be 42 to 48 inches above the floor.
Remove The Old Towel Bar Or Soap Dish
Tape The Fixtures in Place
- In the past, ceramic fixtures such as towel bar holders and soap dishes were cemented right to the wall and the tile was fitted around them. Now most are designed to be glued to the face of the tile with 100 percent silicone caulk. The only tricky part is holding them in place until the silicone sets up. First thoroughly clean the tile with denatured alcohol. Lay a bead of caulk on the back o…
Required Tools For This Project
- Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration. 1. Caulk gun 2. Level 3. Rags 4. Utility knife
Required Materials For This Project
- Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list. 1. Caulk remover 2. Masking tape 3. Silicone caulk 4. Single-edge razor blade