Replacing the Light Bulb
- 1 Remove the cover and lens from the light fixture. The method will vary based on the age of your pool. ...
- 2 Purchase a replacement bulb identical to the bulb in the light. ...
- 3 Unscrew the old bulb and screw the new one into place with a towel. ...
- 4 Turn the power on for 2-3 seconds to test the light and see if it works. ...
How much does it cost to replace pool light fixture?
How much does it cost to replace an inground pool light? On average, it costs $625 to replace pool lights. Pool light repair costs can be as low as $65 to $150 a piece. Depending on the type and function of the bulbs, it costs up to $100 to replace them.
How do you change the light in a swimming pool?
What Are The Steps Involved?
- Safety First! Turn Off the Power. ...
- Remove the Top Screw from the Light. Usually, there is only one screw holding the light fixture to the wall of your pool. ...
- Pry the Light Fixture Out. When the screw is out, put it in a pocket or baggy to make sure you don’t lose it. ...
- Test the Wiring. More safety precautions! ...
- Take the Fixture Apart. ...
- Remove the Old Light Bulb. ...
How to replace light fixture in pool?
Steps on Removing Pool Light Fixture
- Step#1 Turn Off the Power. Shut down the pool’s circuit breaker box. ...
- Step#2 Remove the Screw at the Top of the Fixture. The screw-lock is the one that holds the light fixture to the pool wall. ...
- Step#3 Pry the Light Fixture. With the use of a flat-head screwdriver, force the light fixture out. ...
- Step#4 Pull the Lighting Fixture into the Pool Decking. ...
How to replace a swimming pool or spa light?
Part 3 Part 3 of 3: Reinstalling the Pool Light Fixture
- Replace the lens and reassemble the fixture. Place the gasket and the lens back in place covering the bulb.
- Replace all screws and lock in all tabs to close the light fixture. You’ll simply reverse the disassembling process to re-assemble the pool light fixture.
- Place the fixture back into light niche and screw in the top screw. ...
How to remove a pool light?
How to test if pool light works?
Why is my light bulb dimming?
What to do if light fixture is leaking?
What is the screw that holds a pool light?
How long to bleach LED lights?
How to make sure pool is not getting any power?
See 4 more
About this website
How to Change Pool Light - YouTube
Tropical Pool Supply - 954 597 7480
How to Change a Pool Light Bulb: 11 Idiot Proof Steps
Uh-oh! Your pool light burnt out. Guess you’ll just have to swim on down to replace it… If only knowing how to change a pool light were that easy, right?
How to Replace Underwater Pool Lights | DoItYourself.com
Having a pool on your property is an asset that comes with many repair responsibilities from damaged pumps to nonworking underwater pool lights.Underwater pool lights can last for years but will, at some point, need to be replaced.
How to Change a Pool Light - Leslie's
How many swimmers does it take to change a pool light? It might sound like the beginning of a bad punchline. However, if you’ve ever found yourself with a burned-out bulb in the pool, it might be something you’ve pondered.
How to remove a pool light?
Roll up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock. If the light is low on the side of your pool, or if your arm is too short to reach, you’ll have to get into the pool to unscrew the screw-lock and remove the fixture.
How to test if pool light works?
Turn the power on for 2-3 seconds to test the light and see if it works. Go back to the circuit breaker or pool electrical box and flip the switch back to “on.”. See if the light turns on. If it does, immediately turn the switch back to “off.”.
Why is my light bulb dimming?
This could be caused by various issues. Open up the fixture and make sure there isn't any water inside behind the lens. Dry the lens if it is wet. The dimming bulb may also need to be replaced.
What to do if light fixture is leaking?
If you’re worried that the light fixture may be leaking, you can also purchase a new rubber gasket to seal the fixture and prevent water from getting in .
What is the screw that holds a pool light?
Roll up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock.
How long to bleach LED lights?
If the globe surrounding your LED is sealed, and there are no tabs or screws holding the piece together, place the light in a 2% bleach concentrate for 24 hours.
How to make sure pool is not getting any power?
Check to make sure power is off by trying to turn on the pool lights. You don’t want to risk possible electrocution, so flip the pool lights on and off to make sure the pool isn’t receiving any electrical power. If you only have one pool light, try switching the pool pump on and off.
How much does a pool light bulb cost?
A pool light bulb retails for about $30-40. A new pool light gasket for the fixture is about $25. Labor for the repair would be $100-150. Profit on a successful job would be about $120. The cost of a new fixture is about $200 (wholesale). So for every five bulb replacements I would make $600 and then have to eat $200 plus my call-back labor on the light fixture that leaked. So, that’s six times I’ve visited a pool and I’ve netted $400 in addition/ minus the extra warranty labor. All told that’s about $50 profit per job which just isn’t enough income to make light bulb replacement worth while : (.
How much does a halogen light fixture cost?
After mark-up and labor a traditional halogen white light fixture is about $500 (LED lights are MUCH more expensive). There’s a big difference between $500 and $150! It’s not fair to the customer to have to pay $500 for a burnt-out bulb yet it’s bad business to constantly be warrantying lights with new fixtures.
Can a pool light bulb be replaced?
Its a tough situation but because pool light fixtures leak so often most pool service companies wont perform pool light bulb replacement.
How to prevent electric shock on pool light?
To avoid possible electric shock, turn off the power to the pool light at the circuit breaker. Also at this time try to determine what voltage level your pool light is operating on - 120V or 12V. If your light uses 12V, you will find a transformer usually mounted on the house wall between the circuit breakers and your light fixture. If you control your light remotely, check that your remote system handles low power (<40W) LED lights. Some only support higher power (40 - 500W) incandescent lights.
Where to place gasket and lens on a light?
Place the gasket & lens on top of the light housing.
How to clean old gaskets on eyeglasses?
Clean any old gasket residue from the surface on the lense using a damp rag.
How to know what light bulb to use for pool?
Here, wattage and voltage are especially important. To work out which light bulb model you need, you can pull out your pool user manual to find out the exact type of bulb the fixture requires. Make sure that the new one you buy matches the size, brand, and serial number.
What to do if you don't see the switch in your pool?
If you don’t see the right switch in the main electrical box, have a look around your pool equipment to find the right box. Once you’ve checked that the power is off and no electricity is running to the pool… check it six more times. Getting electrocuted is not part of the process.
How to remove old gasket from pool lens?
Take care when disassembling these pieces and make sure not to drop anything in the pool. Grab a damp rag to remove any old gasket residue from the surface of the lens.
How to check if pool breaker is turned off?
Grab your voltage tester (multimeter) before touching the wires with your hands and test to make sure there’s no electricity running through there. If you’re multimeter registers anything, that means something hasn’t been turned off. Double-check your that your pool breaker is turned off before going on to the next step.
How to loosen a cord on a light fixture?
If the cord doesn’t unravel easily, grab the cord closer to the wall and try giving it a few gentle tugs to loosen it. (Note how the excess cord is stored so you can replace it the same way when you’re reinstalling the light later on.)
How to turn off the power to a pool?
The first (and most important step) is to turn off all power to your pool. Most commonly you’ll have a switch in your home’s circuit breaker box labeled “pool”. Switch this to the off position and then try to turn on the pool lights to make sure there is no power.
How long does it take for a pool light to burn out?
Just a quick peek to make sure the new bulb works and then turn the electricity right back off. If you leave the light on for more than 5 seconds , there’s a chance the bulb will burn out. Normally in the pool, these halogen bulbs have the water to cool them off. So without the water, they get extremely hot.
How to remove a pool light?
Roll up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock. If the light is low on the side of your pool, or if your arm is too short to reach, you’ll have to get into the pool to unscrew the screw-lock and remove the fixture.
How to test if pool light works?
Turn the power on for 2-3 seconds to test the light and see if it works. Go back to the circuit breaker or pool electrical box and flip the switch back to “on.”. See if the light turns on. If it does, immediately turn the switch back to “off.”.
Why is my light bulb dimming?
This could be caused by various issues. Open up the fixture and make sure there isn't any water inside behind the lens. Dry the lens if it is wet. The dimming bulb may also need to be replaced.
What to do if light fixture is leaking?
If you’re worried that the light fixture may be leaking, you can also purchase a new rubber gasket to seal the fixture and prevent water from getting in .
What is the screw that holds a pool light?
Roll up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock.
How long to bleach LED lights?
If the globe surrounding your LED is sealed, and there are no tabs or screws holding the piece together, place the light in a 2% bleach concentrate for 24 hours.
How to make sure pool is not getting any power?
Check to make sure power is off by trying to turn on the pool lights. You don’t want to risk possible electrocution, so flip the pool lights on and off to make sure the pool isn’t receiving any electrical power. If you only have one pool light, try switching the pool pump on and off.
