how do you replace drum brakes on a trailer

How do you replace drum brakes on a trailer?

• Begin by breaking loose all the lug nuts while the trailer is on the ground.
• Remove the dust cap from the axle hub to access the retaining nut.
• Remove the retaining nut from the axle spindle, and then the brake drum from the spindle.
• Remove the inner wheel bearing and wheel bearing seal (red arrows).

Full Answer

How do I remove the drum from my front brakes?

Grab the brake drum by the edges and pull it off. It may help to wiggle it a bit as you pull. It may be necessary to back off the brake adjuster to remove the drum. This is done through the brake adjustment hole in the drum or on the backing plate using a brake adjuster tool to turn the adjuster to loosen the brakes enough to remove the drum.

How do you adjust the rear brakes on a Ford Ranger?

Slide the new or resurfaced drum over the wheel studs. Install lock screws in drum if equipped. Adjust the brakes through the drum or through the backing plate till a slight drag on the brake drum is felt. Reinstall the tire. Check brake adjustment and readjust as needed to have a slight drag on the drum.

Can I adjust my own drum brakes?

These are only general steps based on an American car. Thanks! Don't do your own brakes if you aren't qualified. If you had to read how to remove a wheel, you're not qualified. Thanks! Some drum brake systems don't have a self-adjusting mechanism. Manually adjusted systems usually have a square adjuster at the back of the assembly.

How do you put new brakes on a Toyota Corolla?

Attach the shoes to the wheel cylinder pins. Reattach the parking brake lever. Install the return springs. Using a brake adjustment sizing tool, adjust the brakes to fit the brake drum. Check your new brakes with the photo you took earlier.

How do you remove the drum brakes on a trailer axle?

2:027:52How to remove a trailer brake drum - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy hand you can literally just hand tighten them threads are a little weird right. There the wholeMoreBy hand you can literally just hand tighten them threads are a little weird right. There the whole actual drum is going to come off. So you've got a washer right here. So pull this off.

Can I replace drum brakes myself?

While drum brakes do have a completely different layout and mode of operation than disc brakes do, they are usually no more difficult to service, and often require only a basic set of hand tools and a drum brake adjustment tool to get the job done.

When should I replace my trailer drums?

when should I replace them ? Expert Reply: As long as your existing hub drums are in good condition (no grooves worn in the armature surface that the brake magnet rides on or the surface that the pads grab). For a lot of trailer hub/drums there is a minimum thickness for that to be turned listed on them though.

How do you remove and replace drum brakes?

5:0122:00The ULTIMATE Guide on How to Replace Drum Brakes - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd we're going to hit both sides of the drum. You want to use a good amount of force. And make sureMoreAnd we're going to hit both sides of the drum. You want to use a good amount of force. And make sure you don't hit those studs by mistake. I can feel coming loose. Give it a little wiggle.

What tools do you need to change drum brakes?

You'll need a drum brake retainer spring tool and a pair of drum brake spring pliers. These can often be purchased as a set. You'll also need simple tools like a hammer, pliers, and other assorted hand tools to get everything apart.

How do you remove rear drum brakes?

1:516:48How to Remove a STUCK Drum Brake - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd don't be afraid to hit this hard so now as you're trying to take this off you're trying to doMoreAnd don't be afraid to hit this hard so now as you're trying to take this off you're trying to do like a wiggle back and forth motion as you're pulling. So I'm pulling and wiggling it back and forth.

How do you know if your drum brakes are bad on a trailer?

Unusual brake pedal feel One of the first symptoms of bad or failing drum brakes is unusual brake pedal feel. If the brake drums are worn excessively they can cause vibrations that may be felt in the pedal. Worn drums may also cause shuddering or pulsating that will become noticeable once you step on the pedal.

How do you check drum brakes on a trailer?

0:414:47RV How To - Checking the trailer brakes - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo let me pull this cap off the first thing you want to do is is pull the cap off the dust. Cap.MoreSo let me pull this cap off the first thing you want to do is is pull the cap off the dust. Cap. Then we want to pull the cotter pin out. Sometimes you get a little bit stubborn.

How do I know if I need new trailer brakes?

After a trip, or, once per year is wise. Even if the brakes have had little use, load and weight may cause uneven wear on your braking system. Some obvious signs that your brakes are in need of replacement include noise, pulling, pulsing and pedal depression during braking.

How do you separate drum brakes from hubs?

0:122:11HOW TO Separate the Hub from the Drum - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen you're pressing on it. And then you stand it in the. Press. Sometimes these come out reallyMoreWhen you're pressing on it. And then you stand it in the. Press. Sometimes these come out really hard too they'll really jack up the press and then a little release on the press.

How hard is it to change drum brakes to disc?

All you need is a disc brake conversion kit. Installing one of these kits is a straightforward process that involves removing the old drums, attaching a set of brackets to your wheel hub or axle flange, and then installing the rotors and calipers and hooking everything up.

How do you check drum brakes without removing wheels?

0:333:27How to check brake pads without removing wheel DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil you have a clear picture of your brake caliper caliper bracket and the actual brake pad. AndMoreUntil you have a clear picture of your brake caliper caliper bracket and the actual brake pad. And as you say the brake pad outer brake pad is sunken down pretty good on this particular vehicle.

How to get rid of brake dust?

1. Put on an asbestos respirator. The work you're about to do involves finely-ground brake dust or asbestos dust, and breathing it can be extremely hazardous to your health. Get a mask that's designed for the job of filtering asbestos, not a simple paper one you might use in a shop.

How to keep brakes from getting dusty?

Place the whole brake mechanism in a container and spray it with brake cleaner. Doing this in a container will help keep the dust from becoming airborne. Remember: the dust from most brakes is asbestos, and you don't want to breathe it in. Wear a mask. ...

How to adjust a new shoe?

Place the self adjuster on the new shoes and spread the tops apart to tighten the spring. Put the shoes back in place and slip the retaining pins through the right holes. Install the shoe retainer springs. Attach the shoes to the wheel cylinder pins. Reattach the parking brake lever. Install the return springs.

How to remove a tire from a car?

Remove the hubcap and loosen the lug nuts. Block the front wheels with wheel chocks. Jack up the car and support it with jack stands. Never work on a car supported by a jack alone. Blocks of wood or bricks or even cinder blocks aren't suitable substitutes. Finish removing the nuts and remove the tire. ...

Is it hard to replace drum brakes?

Replacing drum brakes isn't difficult but it requires special tools and a little caution. In return, you save on hefty auto mechanics bills. This article will describe the general process, but you will still want to consult the manual for your car's particular make and model.