- Disconnect the spark plug wire. Disconnect the spark plug wire from the spark plug. PHOTO: Disconnect the spark plug.
- Release the cables from the handle. Pivot the cable clip up and release it from the mower handle. Release the zone control cable from the bail control bar.
- Remove the drive cover. Remove the fuel tank cap. Place a plastic sandwich bag over the fuel tank opening and reinstall the fuel tank cap to prevent gasoline from ...
- Remove the drive cable. Remove the drive cable end from the anchor post. Depress the release tabs and pull the drive cable sheath out of the transmission lever.
- Connect the new drive cable to the transmission. Attach the drive cable end to the anchor post. Push the drive cable sheath into the transmission lever.
- Reinstall the drive cover. Put the drive cover in position on the mower and re-engage the height adjuster lever. Reinstall the drive cover’s top-mounting screws.
- Install the new drive cable on the mower handle. Route the drive cable around the right side of the engine and connect the zone control cable to the drive ...
- Reconnect the spark plug wire. Connect the spark plug wire to the spark plug. Warning: Undertaking repairs or maintenance to appliances or power equipment can be hazardous.
How do you fix a Honda lawn mower belt that is loose?
The most common issue with these Honda lawnmowers is the drive cable stretching. The drive cable has an adjustment that makes this a straightforward fix. An adjustment screw is attached to the drive cable that can be adjusted to pick up the slack of the stretched, inner braided cable. This can also help pick up the slack from a worn-out belt.
How do you replace the drive cable on a John Deere mower?
Route the drive cable around the right side of the engine and connect the zone control cable to the drive cable clip. Reconnect the zone control cable to the bail control bar. Connect the drive cable to the drive control lever. Snap the drive cable clip back into the mower handle. Install new cable ties to hold the cables against the mower handle.
How do you fix a Honda lawn mower that won't start?
The first problem to check for is the drive cable. The most common issue with these Honda lawnmowers is the drive cable stretching. The drive cable has an adjustment that makes this a straightforward fix. An adjustment screw is attached to the drive cable that can be adjusted to pick up the slack of the stretched, inner braided cable.
How do I replace the spark plug on my riding lawn mower?
Disconnect the spark plug wire from the spark plug. PHOTO: Disconnect the spark plug. 02. Pivot the cable clip up and release it from the mower handle. Release the zone control cable from the bail control bar. Release the drive cable from the drive control lever. Depress the release tabs and pull the zone control cable out of the drive cable clip.
How do you change a drive cable on a lawn mower?
1:052:43Replacing the Drive Cable on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition remove the top drive cover mounting screws. Release the height adjuster lever and pull theMorePosition remove the top drive cover mounting screws. Release the height adjuster lever and pull the drive cover off remove the drive cable end from the anchor post depress. The release tabs.
How do you change the drive cable on a Honda hrx217?
0:3415:42Honda HRX217 TDA shift cable replacement part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's only three zip ties that will separate them then we'll get her up on the bench. We'll getMoreThere's only three zip ties that will separate them then we'll get her up on the bench. We'll get the shifter disconnected and then I'll show you how to take that the deck apart.
How do you adjust the clutch cable on a Honda lawn mower?
1:393:25How to Adjust Honda Mower Smart Drive Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo get a feel for resistance. Don't push the smartdrive. And pull backwards the wheels should notMoreTo get a feel for resistance. Don't push the smartdrive. And pull backwards the wheels should not lock up mark. The adjuster tighten the adjuster one revolution. Don't engage the smartdrive.
How do you replace a lawn Boy self propelled cable?
1:5811:48Drive Cable on Lawn Boy Replaced and...... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn the keeper if your wire goes through. And sit down and snap it in place just that easy and thenMoreIn the keeper if your wire goes through. And sit down and snap it in place just that easy and then you'll want to thread. I need to spread that apart a little bit when your screwdriver.
How do you adjust the throttle cable on a Honda lawn mower?
How to Adjust Throttle Cables on a Honda Lawn MowerSlide the throttle lever into the "choke" position.Grasp the throttle cable and pull it toward the lawn mower handle until it is tight. Tighten the screw and release the throttle cable.Attach the spark plug wire back to the spark plug.
How does Honda Smart Drive work?
Smart Drive uses an ergonomically shaped paddle lever designed to be used by either hand. Simply place your hands on the convenient, adjustable control and rotate it to match your mowing conditions. Smart Drive is designed to be used with your palms or thumbs, whichever is comfortable.
How do you fix a Honda lawn mower drive?
0:061:02How to fix Honda lawnmower self propel - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is the adjuster to tighten up or loosen the belt as you're tightening or loosening your handle.MoreThis is the adjuster to tighten up or loosen the belt as you're tightening or loosening your handle. That's basically the clutch for the way the transmission works in this lawnmower.
How do you adjust the speed on a Honda self propelled lawn mower?
Push the drive-clutch lever forward to the handlebar to begin propelling the mower. Move the drive-clutch lever forward slowly to adjust the speed of the mower, making it move faster or slower. Move the throttle lever away from the “choke” position to the “fast” position once the engine warms and you are ready to mow.
How do you fix the self propel on a lawn mower?
0:102:12Top Reasons Lawn Mower Not Self-Propelling - YouTubeYouTubeStart of suggested clipEnd of suggested clipA broken or mystic control cable will prevent the mower from self propelling as well if the cable isMoreA broken or mystic control cable will prevent the mower from self propelling as well if the cable is intact. But doesn't move freely. You can try adding a small amount of lubrication.
How do I fix my lawnmower cable?
0:108:25Repair A Broken Lawnmower Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay so I have a lawn mower handle. On my vise and as you can see this is the cable I'll be fixingMoreOkay so I have a lawn mower handle. On my vise and as you can see this is the cable I'll be fixing this one's working.
How do you change a self propel cable on a Toro lawn mower?
1:093:09Toro Lawn Mower Traction Control Cable Replacement #119-2379YouTubeStart of suggested clipEnd of suggested clipUnhook the spring and remove the old cable install the new traction control cable by first slidingMoreUnhook the spring and remove the old cable install the new traction control cable by first sliding it through the cable guide hook the new spring onto the deck.
How to remove drive cable from transmission?
Depress the release tabs and pull the drive cable sheath out of the transmission lever.
Why won't my lawn mower drive forward?
A drive cable problem is just one reason the wheels of a lawn mower won't drive forward. To learn how to diagnose a lawn mower drive problem, see Lawn Mower Won't Move Troubleshooting Video: Motion Drive Failure.
How to connect transmission cable to mower?
Before attempting to fit the new cable, be sure it’s correct. Check it using the old cable. Fit the transmission cable end through the mower body hole and push the winged outer connector into its anchor. Use your long nose pliers. Now connect the braided cable end into the transmission arm.
How to remove cable from a boat?
With the tab released and the inner unhooked, remove the old cable by pulling it from (upper deck side) the hole.
How to unhook a bail lever?
Unhook Bail Lever – For bail lever-type drive control, squeeze either side of the drive bail lever to unhook (most types).
How to fasten drive cable to handlebar?
Cable Fasteners – Some mowers like Honda may fasten the drive cable to the handlebar by means of a threaded cable end. Using two wrenches, hold one nut and loosen the other, now back off the nuts to release the cable outer end, and unhook the braided cable end from the bail lever, if not already disconnected.
What is an adjuster on a mower?
Most mower drive cables will incorporate an adjuster. The adjuster simply shortens or lengthens the cable as required. Two types are common, the in cable connector adjuster and the cable end adjuster, although slightly different the same principle applies.
How to release a winged cable?
To release the winged type, use pliers to press on the wings and pull the outer cable free .
How much should a cable deflect when checking slack?
Checking Cable Slack – With the cable in place and at rest, the braided cable at the bail lever should deflect by no more than a ¼ inch.
Why is my Honda lawnmower not pulling?
The most common problems and fixes for a Honda self-propelled lawnmower not pulling is the belt being worn out, the drive pulley is worn or broken, or the pins in the gears being worn out. Identifying and replacing these parts is the best way to fix it. Troubleshooting a problem doesn’t have to be hard. Start with the most common issues.
Why is my self propelled Honda mower not pulling?
If your self propelled Honda mower is not pulling, the issue typically lies within the drive cable or a loose belt. However, there are a wide variety of problems that can cause this particular issue. By working on going through each one, you will eventually find and solve the problem.
What happens if your lawn mower transmission is worn?
If your transmission is worn, your lawnmower will be slow or hard to pull. Since the transmission is a solid-state piece, you will not be able to get parts for it. You must replace the entire transmission/drive axle. Since this could be exceptionally pricey, you might want to look into getting a brand new mower.
What to do if drive pulley is broken?
You will need to inspect the drive pulley to make sure it is not damaged or broken. If the piece is broken, you will need to replace the pulley. To do this, you will need the right tools and a place to work on it. If you do not have the tools, you can rent them or have a local small engine repairman fix it for you.
How much does it cost to fix a lawn mower?
In addition, the professional will then charge you labor fees. You can expect to pay anywhere between $30 and $50 for labor fees for someone to fix your mower. This is not to be mistaken for the storage fee or shop fee.
What happens if your drive belt is too loose?
These belts are pretty durable and last a good while. However, if yours does become too loose or worn, it will start to slip. The power will not make it to the engine, and your machine will be slow or unable to pull.
Is it hard to troubleshoot a self propelled lawn mower?
A self-propelled lawnmower may sound like a slightly complicated piece of equipment, but surprisingly, troubleshooting is not that difficult. There are only a few problems that could be causing issues. Fixing these issues is not a heavily involved process and can be done in no time.
Why is my mower throttle cable stuck?
Another common problem encountered is the dryness of the casing or cover enclosing the throttle cable. This could result in the cable becoming stuck or moving with difficulty.
What happens when throttle cable is stretched?
One of such damages is the stretching of the cable. Over time, the cable can become stretched, and this would lead to delayed throttle response .
What Is a Throttle Cable?
A throttle cable, also known as an accelerator cable, is a metal cable that links the gas pedal with the throttle plate. This cable’s function is to facilitate the throttle’s opening when the pedal is pressed or a lever is pushed.
Why won't my lawn mower run faster?
Regardless of the problem you are having with your lawn mower’s throttle cable or the cause of the problem, if the cable breaks , the lawn mower engine can’t run faster. As such, you would need to fix the cable if you can or change it completely.
How to make a wire ring?
Step 1: You would need to procure a 7-inch, #16-wire size aluminum cable and bend it in half. It should be easy to turn since it is made of aluminum. Following the bending, flatten the cable with a pair of pliers. You could further flatten it by using a wire flattening device.
How to make a Z bend?
This should be done carefully as the wire can be cut along with the covering. Once the wire is exposed, use a Z-bender or pliers to create the Z-bend.
Does a lawn mower have a throttle cable?
However, we are not considering the throttle cable of a car today. The lawn mower’s throttle cable also helps to control the speed of the mower and, consequently, the engine speed. It does this in much the same way as the throttle cable of a car, and its effect also controls the speed of the blades during mowing.
Where is the drive cable on a lawn mower?
Locate the drive cable of the mower. You will find it near the lawnmower handle. A lever is attached to the cable and releases the lever from the cable.
How to install a new drive cable?
Take the new cable and install it starting from the anchor post. Follow the reverse process to install the new drive cable.
How long does it take to fix a self propelled lawn mower?
Basically fixing the problem of self-propelled lawnmower cable is not a troublesome task. You approximately need 20-25 minutes to complete the entire task. Let’s see the required tools at first before entering the fixing process.
What happens if you damage a cable on a lawn mower?
But what about a damaged cable of it? with a damaged cable, you won’t be able to control the mower properly. It also leads the mower to run poorly.
Do you have to unplug a lawn mower spark plug?
Unplug the mowers’ spark plug. Every lawnmower has a spark plug and before doing any repair, you must unplug it. It will save you from being electrified at the time of repair.