- Unscrew the fastenings that connect the two halves of the blower housing with the screwdriver; both the shroud cover and the blower fan cover will be removed to expose ...
- Cut the damaged starter cord with the utility knife and remove it from the pulley. ...
- Cut a new cord that is the same length as the old cord with the utility knife. ...
- Feed the new cord through the starter guide to the pulley with your fingers, placing it exactly where the old cord had been.
- Reattach the housing and refasten the screws with the screwdriver.
- Detach the handle and starter bushing from the old cord with the screwdriver. The starter bushing is the small cylindrical piece in the center of the housing.
- Tie a simple knot in the cord to hold it onto the handle. ...
How to replace the pull cord on a Homelite leaf blower?
Instructions for the Homelite Leaf Blower Pull Cord Replacement 1. Unscrew the fastenings that connect the two halves of the blower housing with the screwdriver; both the shroud cover... 2. Cut the damaged starter cord with the utility knife and remove it from the pulley. Pay attention to the ...
How do you fix a Homelite pull start cord?
Drain any fuel from the trimmer fuel tank before attempting to repair the Homelite pull start cord to prevent fuel spills. Unscrew the throttle cable bracket retaining screw from the pull start cord housing with a T-25 Torx head screwdriver to remove the throttle cable from the trimmer.
Can you repair a broken pull rope on a Homelite Trimmer?
The pull start rope on your Homelite trimmer can fray or wear out with use and eventually break. Instead of repairing the old, damaged pull rope, the best option is to replace it with a new pull rope, which can be accomplished by disassembling the trimmer body to access the old rope.
Should I replace my leaf blower’s starting cord?
As your leaf blower ages, the starting cord may become damaged. Fraying or snapping of the cord is common; however, there is no need to replace the entire starting recoil. Replacing just the rope can get you back to work. This procedure can be done in a short amount of time with only a few tools and does not require extensive skill.
How do you change a blower string?
2:366:24How to Replace a Broken Blower / Trimmer String Pull Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you wrap the end around where the screw will tighten against it. And then wrap a loop around theMoreAnd you wrap the end around where the screw will tighten against it. And then wrap a loop around the shaft. There we go pull it tight and then you can put the screw back in the screw has teeth.
How do you fix a pull start that won't retract?
0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.
Who makes Homelite Leaf Blowers?
However, Homelite manufactures other power tools as well, including leaf blowers. The company is nowadays a subsidiary of Techtronic, under which it has shifted its portfolio to include almost exclusively lawn equipment. Homelite products are reported to be manufactured mainly in China.
How do you replace the pull cord on a Homelite chainsaw?
0:0012:00Replace Pull Rope Homelite XL12 - YouTubeYouTubeStart of suggested clipEnd of suggested clipDriver the top screw is the short one all three all of the other three are the same size.MoreDriver the top screw is the short one all three all of the other three are the same size.
How do you fix a pull cord?
0:352:51How-To: Fix a Broken Recoil Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe've applied a double knot on the other end of the rope. We've done the same thing we drew the ropeMoreWe've applied a double knot on the other end of the rope. We've done the same thing we drew the rope through the handle. And apply - double knot at the end.
Why does my pull cord get stuck?
Problems With the Recoil Mechanism Sometimes the pull cord crosses over itself when rewinding, and when this happens, it can get stuck. You may be able to free it by pulling it gently to coax it out to its full length, then letting it rewind slowly.
When did Homelite go out of business?
Nov. 16, 2001Deere & Company announced on Nov. 16, 2001 that it has sold its Homelite consumer products business.
Are Homelite and Ryobi the same?
From what I understand from Home Depot, Ryobi and Homelite are made by the same company. Husqvarna makes a lot of trimmers that are rebranded (Craftsman's and I think Black and Decker are two of them).
How much does a Homelite leaf blower cost?
Compare with similar itemsThis item Homelite UT09526 150 mph 400 CFM 2-Cycle Handheld Gas BlowerCraftsman B215 25cc 2-Cycle Engine Handheld Gas Powered Leaf Blower - Gasoline Blower with Nozzle Extension for Lawn Care, Liberty RedPrice$11292$13999Sold ByTheCountryButlerAmazon.com3 more rows
How do you put a string on a chainsaw?
1:473:58How to Replace a Starter Rope on a Stihl Chainsaw....The Easy Way by ...YouTubeStart of suggested clipEnd of suggested clipSlide it through same as before we're going to tie it small knot at the top now that our rope isMoreSlide it through same as before we're going to tie it small knot at the top now that our rope is installed at both ends we're going to slide it through all the way the inside of the cover.
How do you change a pull string on a Poulan chainsaw?
4:225:42Poulan Chainsaw Repair - How to Replace the Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipTie an other simple overhand knot in the end of the rope I want to keep that tag end as short as IMoreTie an other simple overhand knot in the end of the rope I want to keep that tag end as short as I can pull that knot up into the opening on the handle.
How do you change a starter on a chainsaw?
1:235:47How to Repair the Starter on a Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we can go ahead and reassemble the starter I'll start by replacing the starter pulley on to theMoreNow we can go ahead and reassemble the starter I'll start by replacing the starter pulley on to the starter spring and make sure that the pulley engaged against the spring.
What is a pull cord on a homelite leaf blower?
By Sarah Mason. Non-electric Homelite leaf blowers use a starter cord, also called a pull cord, to start the engine. This cord can become worn and break over time due to repeated use. If your Homelite leaf blower's starter cord breaks, you can replace it yourself to save time and money.
How to keep cord from fraying?
You can use utility tape instead of a lighter to prevent the cut ends of the cord from fraying. You may use scissors instead of a utility knife to cut the cord. If using a lighter to prevent the cord from fraying, do not allow it to catch on fire. If it ignites, blow it out quickly.
How to remove rope from pulley?
Remove the old rope from the pulley — be observant of the direction you unwind the remaining cord for re-installation. The rope has a knot on the inside of the pulley, simply pull rope out by pulling on the knot. Remove the rope from the starting handle. Separate the starting handle into two pieces , using the screwdriver. Cut the knot off of the rope and pull the excess out.
How to reattach a rope handle?
Reattach starting handle by feeding the rope through the eye and tying a knot, cutting off any excess. Reassemble handle.
Do you need to replace the starting cord on a leaf blower?
As your leaf blower ages, the starting cord may become damaged. Fraying or snapping of the cord is common; however, there is no need to replace the entire starting recoil.
How long do Homelite string trimmers last?
Homelite string trimmers are reliable and sturdy, lasting for years if cared for properly. The starter cord on these trimmers can get frayed or broken over time and will need to be replaced. This is a minor repair that can be accomplished with a few tools and a little knowledge of the trimmer. On some models though, it may require you to remove ...
How to remove a clutch from a car?
Step 1. Pop off the rubber spark plug boot from the spark plug. Use the socket wrench to take out the spark plug. Insert the piston stop tool into the spark plug hole. This blocks the piston from moving, which will allow you to remove the clutch.
How to unscrew a car engine?
Use the screwdriver to unscrew the engine from the handle. Remove all of the screws and set them aside in a safe place. Take off the engine's front cover and remove these screws as well.
How to get a recoil spring out of a pulley?
Hold the pulley with one hand and pull out the cord at least two full rotations. Wind it back on the pulley and repeat this until the recoil spring has full tension.
How to secure pulley retainer plate to housing?
Position the pulley retainer plate flush against the housing. Tighten the three pulley retainer plate retaining screws with a T-25 Torx screwdriver to secure the pulley retainer plate to the housing.
Where is the throttle cable located on a carburetor?
The carburetor throttle linkage is located on the front of the carburetor between the rope housing and air filter box. Slide the throttle cable from between the housing and air filter box.
How to tie a rope knot?
Pull the rope out from the handle; tie a knot tightly on the mark. Pull the knot tightly with pliers and cut the excess rope just above the knot. Pull the rope through the bottom of the handle until the knot rests in the handle top hole.