To replace the timer in your washer first confirm that the timer knob is pushed in then rotate the knob counter-clockwise to remove. Pull the indicator dial and washer off. Next, remove the screws securing the top panel. Now lift the panel up and push forward to remove.
Full Answer
How do you remove the timer on a whirlpool washing machine?
If your timer knob has a skirt or dial surrounding it, push the timer knob in and unthread the knob by turning it counterclockwise. On some washers, there’s a plastic cap in the middle of the knob. You’ll need to pop the cap off to get to the fastener that holds the knob on.
How do I replace the timer knob on my Kenmore washer?
There are a few variables in removing the knob in order to replace it. If your timer knob has a skirt or dial surrounding it, push the timer knob in and unthread the knob by turning it counterclockwise. On some washers, there’s a plastic cap in the middle of the knob.
How do I troubleshoot a Kenmore washer that won't turn on?
Unplug the washer, use your model’s wiring schematic to find the terminals in the timer that control the timer motor, and use your multi-meter to check them. Then check the timer motor itself for electrical continuity.
How do I troubleshoot a timer that is not working?
Safety first should be your guiding motto. To troubleshoot a timer, you will perform continuity tests using a digital multimeter. Unplug the machine's power cord from the wall outlet before opening up the machine’s control panel.
What is a washing machine timer?
The washing machine timer can be considered the brain that controls the washing machine's systems. Although timers are ruggedly constructed, they contain a variety of tiny parts, like springs and movable contacts, that can develop problems that keep the machine from operating properly. The movable contacts can become burned ...
How to troubleshoot a timer?
Safety first should be your guiding motto. To troubleshoot a timer, you will perform continuity tests using a digital multimeter. Unplug the machine's power cord from the wall outlet before opening up the machine’s control panel. The timer’s failure to advance could be caused by a defective timer motor, the motor’s control contacts stuck in the open position or defective drive gears. Unplug the timer’s wiring harness, then, with the timer set to any position other than off, check for continuity through the motor contacts. Continuity will be indicated by a “0.000” on the meter’s display. A pictorial diagram on the back of the machine will tell you which numbers on the timer socket corresponds to which set of contacts in the timer. Likewise, a functional timer motor will display a resistance reading greater than 0.000, but less than 5 ohms. Open contacts or a defective motor winding will be indicated by an “O.L.” on the meter’s display.
Can a defective timer work?
A defective timer will only work in some cycles and not others. One or more of the timer’s contacts that control that cycle are stuck in the open position. To make sure that the problem actually is a defective timer and not a broken wire in the wiring harness, check for continuity through those contacts using your meter.
How to check if washer lid is tripped?
A pin or lever attached to the lid will activate the switch when the lid is closed. Unplug the washer and see if the switch is tripped by a lever or actuator when the lid shuts. Remove the wires from the switch and use your multi-meter to check for electrical ...
How does a timer motor work?
The timer motor, which advances the timer , receives its signal to start up from the water level switch. That signal comes when the tub has filled enough to trip the water level switch. So if your washer is filling with water but the timer is not advancing, it would be logical to make sure the water level switch is sending the electric signal to ...
What happens if the top lid of a washer is open?
When a washer’s top lid is open, the motor circuit will not operate. This safety feature is crucial to preventing serious injuries, and you ought not to bypass it. If your lid switch is broken, the timer won’t operate either, and repair is in order. Start by finding the lid switch, which is normally located beneath the main top.
Why is my washer not moving on?
So if the problem is that your washer is not moving on at the end of wash time or rinse time, check if the pump is actually removing the water.
Where is the cap on a washer?
On some washers, there’s a plastic cap in the middle of the knob. You’ll need to pop the cap off to get to the fastener that holds the knob on. And there are some washer models that have a retaining shaft behind the timer itself that you’ll need to release to remove the knob. If there’s a retaining clip made of metal on the shaft of the timer, ...
Why does my washing machine stall?
So a stall at the wash or rinse cycle could be a result of a broken water inlet valve or an obstruction in the hoses that bring the water in. Unplug the washer, disconnect the inlet hoses, and check that they are clear and unkinked, and that their filtering screens aren’t gummed up. Then use a multi-meter to verify that the solenoids to open the valve don’t have open circuits. If your washer passes these tests then the next step is to call in a service technician to measure the voltage coming into the solenoids when the cycle of the washer is on fill. Perhaps there is no voltage coming into the valve, which means the electrical process is being halted somewhere else in the machine, like the water level switch, the timer, the lid switch, or the cycle selector switch.
1. Washer Is Still Trying To Drain
Your washing machine will not leave the spin cycle unless all the water has drained out first. If you notice water in your washer’s tub during spin cycles, it means that the washer isn’t draining. Read this article to learn how to fix drainage issues in your Frigidaire washing machine.
2. Defective Control Board
If your washing machine’s control board is damaged, your may not progress beyond the spin cycle. Read this article to learn how to replace a damaged control board in your Frigidaire washing machine.
3. Faulty Timer
Another thing that could cause your Frigidaire washing machine to get stuck on a spin cycle is a damaged timer. Here’s how to replace the timer in your washing machine…
