How to Replace Your Maytag Washer’s Water Inlet Valve Assembly
- 1. Unplug the washer and turn off the water supplies. First, unplug the washer. ...
- 2. Disassemble the machine to access the water inlet valve assembly under the console. First, you will need to flip the top panel of the washer over. ...
- 3. Remove the water inlet valve assembly. ...
- 4. Replace the water inlet valve. ...
- 5. Install the new wire harness. ...
- 6. Reassemble the machine. ...
How do you replace a water inlet valve on a refrigerator?
Remove the mounting screws holding the old water inlet valve in place. There should be two of them holding the metal bracket to the fridge frame. Pull the valve out of the refrigerator and disconnect each wire harness. These connectors should be color coded, but if they aren’t, make note of which goes where.
How do you fix a water leak in a whirlpool refrigerator?
Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver. Place a container under the valve to catch any water that may spill from the water valve and its fill tube. Remove the water valve's fill tubing. Loosen the flare nut on the brass fitting that is found on the inlet side of the water valve.
How do you remove water from the back of a refrigerator?
Disconnect the water supply line Pull the refrigerator away from the wall far enough so you can access the water line connection and work on the back of the refrigerator. Place a towel under the water valve assembly to catch water. Loosen the nut on the supply water line until the water line is free.
How to replace the water inlet valve on a Maytag washer?
How to Replace Your Maytag Washer’s Water Inlet Valve Assembly. 1. Unplug the washer and turn off the water supplies. First, unplug the washer. This should be the first thing you do before starting any appliance ... 2. Disassemble the machine to access the water inlet valve assembly under the ...
How do you remove the Maytag inlet valve?
2:596:12How To: Whirlpool/KitchenAid/Maytag Water Inlet Valve WP8540751YouTubeStart of suggested clipEnd of suggested clipAll you have to do is lift up on these little locking tabs and pull them out.MoreAll you have to do is lift up on these little locking tabs and pull them out.
Where is the water valve located on a Maytag refrigerator?
0:266:22Whirlpool/KitchenAid/Maytag Refrigerator Water Inlet Valve ...YouTubeStart of suggested clipEnd of suggested clipWe need to remove the access panel. I'm gonna use the core inch nut driver and going to take out theMoreWe need to remove the access panel. I'm gonna use the core inch nut driver and going to take out the screws that holds the panel.
How do I test my Maytag refrigerator water inlet valve?
1:012:46Refrigerator Not Making Ice? Inlet Valve Test, TroubleshootingYouTubeStart of suggested clipEnd of suggested clipUse a probe to touch one terminal of the coil you're testing and the second probe to touch the otherMoreUse a probe to touch one terminal of the coil you're testing and the second probe to touch the other terminal if the meter reading shows a result between 500. And 1500 ohms of resistance.
How do you know if your water inlet valve is broken?
Signs pointing to a faulty inlet valve include:Leaks that fill the dishwasher when it's off.Inadequate water for a cycle. ... A bad inlet valve can lead to leaks from the dishwasher onto the kitchen floor. ... Most inlet valve malfunctions stem from a defective seal or solenoid failure.
What does dual water inlet valve do?
Dual valve which means this valve is responsible for delivering water to the ice maker and also the water through the door. If one is not working then most likely replacing this valve will solve the issue. Make sure your ice maker line in the back that goes into the freezer is not frozen up.
How do I turn off the water to my Maytag refrigerator?
1:182:13How to locate and turn off the water supply to your refrigerator - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo usually that's that's um meaning that the water is flowing through there so to turn it off youMoreSo usually that's that's um meaning that the water is flowing through there so to turn it off you just have to twist it perpendicular to the direction of the line.
Can a water inlet valve get clogged?
Check for clogs in the filter screens in the water inlet valve, which can block water flow. This is a common reason water inlet valves fail and it is the easiest problem to remedy. Use a flashlight to look inside each of the two hose fitting ports on the water inlet valve—there should be a screen inside the port.
How do you replace the water inlet valve on a refrigerator?
0:161:23How to Replace a Refrigerator Water Inlet Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace a towel under the water valve assembly to catch water loosen. The compression nut and pull theMorePlace a towel under the water valve assembly to catch water loosen. The compression nut and pull the water line free remove the screws from the rear compartment cover and pull the cover off remove.
What tells the ice maker to fill with water?
Once the ice maker has been connected to a power and water source (aka the plumbing line connected to the back of your refrigerator), the ice maker cycle should begin automatically. At the beginning of the cycle, an electrical signal is sent to a water valve to fill the ice mold with water.
How do you test the water inlet valve on a refrigerator?
0:182:23How To Test Your Fridge's Water Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut this process might be similar and all makes and models just connect your fill line from yourMoreBut this process might be similar and all makes and models just connect your fill line from your water valve. Remove any wire harness or harnesses from your water valve push down on the tabs.
How much does a water inlet valve cost?
How Much Does a Water Inlet Valve Cost? Dishwasher water inlet valves are inexpensive parts, usually costing only about $15 to $35. Some water inlet valves will cost more because they are specific to a particular brand.
How do you test a water inlet valve?
1:422:50Washer Not Filling? Water Inlet Valve Testing, Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo help determine this shut off the water supply. Disconnect the hot and cold water supply linesMoreTo help determine this shut off the water supply. Disconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or a washtub.
Why isn't my ice maker filling with water?
Check the refrigerator's filter. When there is no filter, or it is clogged, the ice maker does not get water. Make sure that the filter is in place, and if it has not been changed in more than six months, replace it with a new one.
How do you test an ice maker solenoid valve?
Attach the two multimeter probes to each solenoid contact. Read the multimeter's display. A properly working solenoid will reflect a 200 to 500 ohm reading. Replace the solenoid if it produces no reading or has a large displayed value.
Why is my ice maker not working but water does?
If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi.
How do you test a whirlpool ice maker water valve?
0:392:23How To Test Your Fridge's Water Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe two metal probes together will zero out to test your Bell touch one probe to each terminalMoreThe two metal probes together will zero out to test your Bell touch one probe to each terminal depending on the part your valve canary between 200 and 500 ohms.
Finding The Right Valve For Your Refrigerator
To find the right part, you’ll need your appliance’s model number. Your refrigerator’s model number will be in the manual for sure, but if you don’t have that on hand, you can search by model number in the search box above or on AppliancePartsPros.com
How To Replace A Refrigerator Water Inlet Valve
The steps laid out in this article and the companion video were completed on a Whirlpool refrigerator. Even if you have another brand or model of refrigerator, though, this guide should still help! If something in our guide doesn’t line up with your refrigerator, refer to your appliance manual for specific instructions.
Wrapping Up
With the right tools and a little bit of time, you can fix a damaged water inlet valve all by yourself, saving you some money and the stress of shopping for a new appliance or tracking down a professional technician. We hope this how-to has helped you out, and if you need a bit more guidance on this particular task, check out our tutorial video.
How to remove water valve from cabinet?
You should now be able to locate the water valve. Using your quarter-inch screwdriver, you will want to remove the machine screws that are holding the water valve to the cabinet. Once these screws have been removed, you should be able to pull the valve outside of the cavity, allowing access.
Where is the water inlet valve located?
This valve is usually located at the back of the fridge near the bottom. It supplies water to the dispenser and water the icemaker. The electronic part of the valve can ...
How long do you have to unplug a fridge to reset?
You either installed it wrong or you may just need to unplug the fridge for a full minute for the replacement to be reset.
How to remove the cardboard cover from a refrigerator?
Remove the cardboard cover on the back of the fridge. Locate the screws in the upper right hand corner of the refrigerator and use a nut-driver to remove them.
How to change the back of a refrigerator?
1. Pull the refrigerator forward so that you can get behind it with ease to change the part. Before messing with the back, be sure to unplug the refrigerator and turn off the water supply. 2. Remove the cardboard cover on the back of the fridge.
How to make sure tubing snaps into place?
Reinsert the tubing that you polished up earlier. Lightly push it in to make sure that the new tubing snaps into place. When inserting the tubing, just make sure that it's firmly in place and doesn't move around when you poke at it, and that it is snug.
Do you have to replace the water inlet valve?
Nowhere, you have to replace the entire water inlet valve, they're integrated into it.
How to check water valve in refrigerator?
To check the refrigerator water valve, unplug the power cord and shut off the water supply to the refrigerator. Most foods will be okay if left in the refrigerator as long as the doors are closed; power will be off for only about 30 minutes when checking the valve. Wear work gloves to protect your hands. Access the water valve, usually found ...
How to check for electrical failure in refrigerator?
To check for an electrical failure, access the refrigerator water valve usually found at the bottom rear of the refrigerator cabinet. Use either a digital or an analog multimeter to check continuity–good electrical current–of the valve solenoid coils.
Where to place buckets on water line?
Place a bucket under the end of the water supply line.
Why is my ice maker not reaching the ice cube tray?
Water not reaching the ice cube tray could indicate a problem with the water inlet valve, but not always. The water line from the water valve to the ice maker can freeze, not letting water into the ice maker.
How to turn off water supply on refrigerator?
You may want to place scraps of carpet, of some other soft material below the fridge to prevent damage to the floor. Turn of the water valve's water supply by closing the shut-off valve in the waterline leading to the water valve. Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver.
How to remove water from refrigerator?
Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver. Place a container under the valve to catch any water that may spill from the water valve and its fill tube. Remove the water valve's fill tubing. Loosen the flare nut on the brass fitting that is found on the inlet side of the water valve.
How many wires are in a water valve?
There are two wires connecting to the terminals of your water inlet valve. If yours is a double solenoid water valve, it will have four wires. Be sure to label each wire so that you know where to reconnect them later. Firmly grasp the metal connector of the wires in order to remove the wires.
What to do if water valve is not working on ice maker?
Replace the water valve that feeds water to the ice maker and water dispenser if it no longer controls the flow of water.
What happens if the water inlet valve fails?
If the water inlet valve fails, it won't open to allow water flow, or it lets water flow constantly even when the refrigerator is unplugged. If the water inlet valve is defective, replace it with a manufacturer-approved fridge part.
How to keep refrigerator from deteriorating?
Safely store any food that could deteriorate while the refrigerator is shut off. Then unplug the refrigerator or shut off the circuit breaker for the refrigerator. Close the water supply cut-off valve for the ice maker.
How to tighten compression nut on water valve?
Wrap a small amount of pipe thread tape around the water supply line fitting on the back of the water valve. Fit the water line into the water valve assembly and tighten the compression nut firmly.
Why is my refrigerator not adjusting the temperature?
If the temperature in your refrigerator doesn't match the temperature you set, the problem could be the temperature control board— a service technician can give you a definite diagnosis. If the board is at fault, follow these steps to replace it yourself.
How to remove the service panel on a refrigerator?
Use a Phillips screwdriver to remove the screws that secure the lower service panel on the back of the refrigerator. Remove the panel.
How to catch water from a water valve?
Place a towel under the water valve assembly to catch water. Loosen the nut on the supply water line until the water line is free. Tip: If needed, refer to the owner's manual for additional guidance with disconnecting the water line. PHOTO: Disconnect the water supply line.
How to turn off water supply on refrigerator?
You may want to place scraps of carpet, of some other soft material below the fridge to prevent damage to the floor. Turn of the water valve's water supply by closing the shut-off valve in the waterline leading to the water valve. Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver.
How to remove water from refrigerator?
Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver. Place a container under the valve to catch any water that may spill from the water valve and its fill tube. Remove the water valve's fill tubing. Loosen the flare nut on the brass fitting that is found on the inlet side of the water valve.
How to test continuity of water inlet valve?
Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve.
How many wires are in a water valve?
There are two wires connecting to the terminals of your water inlet valve. If yours is a double solenoid water valve, it will have four wires. Be sure to label each wire so that you know where to reconnect them later. Firmly grasp the metal connector of the wires in order to remove the wires.
What is the water inlet valve assembly on a Maytag washer?
The water inlet valve assembly controls and distributes water to different dispensers in your Maytag washer. But if the body cracks, water can leak throughout the machine. Over time, the solenoids can also fail and won’t distribute water correctly. You can replace this part yourself. Order replacement part #W10364988 for most Maytag washer models and follow these steps to install it.
How to lock a washer on a washer?
First, remove the belt and then carefully swing it down until it rests on top of the machine. Make sure the corner holes near the lid line up with the bolts on top of the washer. Once it’s down and in place. press it firmly down until you hear the locks engage.
How to connect a thermistor to a wire box?
Start with the blue thermistor wires. Insert the wires into each of the mounting tabs along the length of the wire box. Use a flathead screwdriver to carefully open the tabs and push the wires into place. Lace the end of it under the other wire harness and add a new zip tie to attach the one the rmistor wire to the other bunch of wires. Then plug in the thermistor wires.
How to get wire out of gray wiring box?
You may need to use a flathead screwdriver to pry the wire out of each tab without damaging either the wires or the plastic tabs. The wiring goes all the way to the right side of the gray wiring box. Once you’ve reached the right side, detach the two wide wire harnesses that slot into the right side of the box by depressing the mounting tabs on each one .
How to remove a hose head from a hose?
Each hose is clamped in place. Use pliers to compress and loosen the clamp. Then slide the clamp away from the hose head and remove each hose head from the ports.
How to secure a washer console?
Line up the five mounting tabs at the interior edge of the console with the body of the washer. Then flip the console over and click the three back tabs with the screws into place. Tighten the screws to secure the console.
Does water intel have solenoids?
Your part may have come with a new wire harness with the water intel assembly has a newer type of solenoids. Whether you’re using a new wiring harness or reusing the old one, the steps are the same:
