Effortlessly use your hose at any length with the specially designed 'stop-anywhere' locking mechanism. To tidy your hose away, simply give it a gentle tug and the automatic rewind feature will retract your hose and neatly coil it inside the unit using the integrated self-layering mechanism, saving you precious time and energy. Built Tough
Full Answer
How do you remove the hub from a retractable hose reel?
Use the screwdriver to unscrew the hub plate, but do not remove the plate from the hose reel. With the hub unscrewed, place your socket wrench on the center hub nut and hold firmly. Note the factory preset and turn the hub nut the number of times recommended for your retractable hose reel.
Can you use a hose reel on a retractable hose?
This hose has been specifically designed for use in a retractable hose reel unit and must be soft and pliable so that it retracts easily. Although this hose is not designed for kink-resistance specifically, using a hose reel greatly reduces the likelihood of kinks.
How do I remove the Kinks from my hose reel?
You may wish to use a hose reel cover to prevent this problem again. Extend the hose and turn tap on full to remove any kinks. The hose should not retain a memory and kinks should fill out. Ensure the hose reel is mounted high enough, if too low the hose can rub on the aperture and cause kinks.
How do I adjust the tension on my hose reel?
In order to adjust your particular model of hose reel system, you will need to consult the owner’s manual. It should tell you how many turns are needed for proper tensioning of your retractable hose reel.
How do you retract Hoselink?
Retracting the hose To unlock the hose, give the hose a small tug to start retraction. If you pull the hose too far, it will lock again rather than start to retract. To shorten the hose, start retraction then once at the desired point, stop and walk back out a little to lock it at the new length.
How do I get my retractable hose to retract?
Step-by-StepBefore retracting the hose turn off the tap.Tug the hose to retract.Slowly walk the hose back.Pull the lever on the hose gun to release water pressure.
How do you rewind a Hoselink?
0:533:43Hoselink Auto Rewind Hose Reel "REVIEW" - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt comes out that easy. And once you pull it out it just simply locks in place. Then when you'reMoreIt comes out that easy. And once you pull it out it just simply locks in place. Then when you're done you just give it a slow pull and it automatically rewinds the hose into the housing.
Why does my Hozelock not retract?
Why does the Auto Reel not retract all the time? We recommend pulling out all the hose. Clean any excess debris from the outside of the hose such as sand and dirt with a damp cloth. Now, let the hose retract slowly by walking back to the reel holding the end stop.
How do you retension a retractable hose reel?
To increase spring tension: Adding wraps of hose will increase spring tension. This can be accomplished by pulling out approximately 10 feet of hose, hand feed hose back up through roller bracket assembly* until loop is large enough to slip over spool. Add two or three wraps until desired tension is achieved.
How does a retractable hose reel work?
Spring driven hose reels have a spring mechanism that retracts the hose automatically. As the hose is unwound, the tension on the spring builds and is stored. When the job is done and the tension is released, the hose retracts to the reel.
How do you fix a Hoselink hose?
1:202:56How to Fix Leaking Hoselink Hose Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipUnscrew the yellow nut and using a small screwdriver release the white split ring from inside theMoreUnscrew the yellow nut and using a small screwdriver release the white split ring from inside the connector. Place the connector. And the hose into a cup of hot water for a few seconds.
Can you replace the hose in a retractable hose reel?
You can now fix any small hose using the Retractable Reel Hose Repair Kit. This kit will enable you to cut out and repair the damaged hose section, so you can continue to use your hose reel.
How do you open a Hoselink reel?
Use a flat screwdriver to remove the side cover located on the same side as the leader hose. This is not rust as stainless steel screws are used throughout. It is from a bug that has made a home in the screw hole. Clean out holes with hot soaping water.
What is the spring for in a Hozelock reel?
The spring is to be inserted into the end of the hose that goes inside the reel. This is to prevent the hose from kinking when in use.
Why does the hose keep popping?
This is caused by high pressure within the system forcing the hose off. Often the clips that hold the hoses in place are not strong enough to withstand this pressure. If the hoses pop off you will know immediately as it will affect performance considerably.
How do you open a Hoselink reel?
Use a flat screwdriver to remove the side cover located on the same side as the leader hose. This is not rust as stainless steel screws are used throughout. It is from a bug that has made a home in the screw hole. Clean out holes with hot soaping water.
How does hide a hose work?
The Hide-A-Hose Retractable Hose System harnesses the suction from the Power Unit (usually installed in the garage) to retract the hose back into the PVC tubing hidden within the walls, attic, and floor joists, of your home. The hose is retracted directly into the tubing without being coiled or compressed.
How do you fix a Hoselink hose?
1:202:56How to Fix Leaking Hoselink Hose Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipUnscrew the yellow nut and using a small screwdriver release the white split ring from inside theMoreUnscrew the yellow nut and using a small screwdriver release the white split ring from inside the connector. Place the connector. And the hose into a cup of hot water for a few seconds.